• 에너지공학
• /
• 제8권2호
• /
• pp.272-278
• /
• 1999

본 연구에서는 지름 30mm, 길이 45mm인 brass와 aluminium 원통 실린더의 접촉면이 ⅰ) 진공 상태에 있을 때 , ⅱ) silicone grease를 충전하였을 때 , ⅲ) silicone grease와 aluminium 분말 (#325) 혼합물을 충전하였을 때의 열접촉저항을 측정하였고, 그 결과를 Fouche 의 해석 모델과 비교하였다. 진공상태에서 비접촉면의 열접촉저항은 표면의 가공 상태에 따라 (2~100)$\times$$10^{-5}$($m^2$$^{\circ}C$/W)의 분포를 나타내었고 접촉 표면을 연마하였을 때에는 거친 표면에 비하여 약 30~50%의 열접촉저항저감을 나타내었다. 그러나, silicone grease를 충전했을 때에는 열접촉저항 값이 약 5~10정도 감소하는 경향을 나타내었다. Fouche 모델을 이용한 해석 결과는 silicone grease로 충전한 접촉면에 대해서 각 10~30%범위에서 아주 잘 일치하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.427-432
• /
• 2005

This study treats the advantage of in situ line source method measuring the heat transfer capacity of a borehole, using mobile equipment, to determine the thermal properties of the entire borehole system such as thermal conductivity, diffusiveity. volumetric heat capacity, and borehole thermal resistance. The results from the response test include not only the thermal properties of the ground and the borehole, but also conditions that are difficult to estimate, e,g. natural convection in the boreholes, asymmetry in the construction, etc. In this study, 1) theoretical in situ methods for assessing working fluid temperature variation in V-type PE tube have been introduced, and 2) TRTE(Thermal Response Test Equipment) has been built based on these kinds of theoretical in situ methods. Basically TRTE consists of a pump, a heater and temperature sensors for measuring the inlet and outlet temperatures of the borehole. In order to make equipment easily transportable it is set up on a small trailer. Since the response test takes above two days to execute, the test was fully automatic in recording measured data using Labview DAS(Data acquisition system) program. The test was demonstrated in the course of intensive research in this field through the one site at Ulsan city in Korea. From this kind of thermal properties test of borehole systems in situ, the design of the borehole system can be optimized regarding the total geological, hydro-geological and technical conditions at the location.

• 한국도로학회논문집
• /
• 제12권3호
• /
• pp.113-119
• /
• 2010

본 연구는 고로슬래그미분말 및 실리카흄과 같은 광물질혼화재를 사용한 시멘트콘크리트 포장의 성능에 대한 역학적, 물리적 평가를 수행하였다. 광물질혼화재 사용 시멘트콘크리트 포장의 휨강도, 압축강도, 통과전하량, 염소이온 확산계수 및 초기표면흡수율을 소정의 재령에서 측정하였으며, 그 결과를 기준 콘크리트 포장의 성능과 비교하였다. 실험결과, 광물질혼화재의 종류에 따라 시멘트 콘크리트 포장의 강도거동은 다르게 나타났으며, 대체적으로 실리카흄을 사용한 콘크리트의 압축강도 발현이 다소 우수하게 나타났다. 뿐만 아니라, 콘크리트의 염소이온 확산계수는 기준 콘크리트에 비하여 매우 작은 경향을 나타냄으로써, 이는 광물질혼화재를 사용한 시멘트콘크리트 포장의 우수한 내염성을 다시 한번 확인 할 수 있었다. 도출된 실험결과를 바탕으로 하여, 향후 고성능 시멘트콘크리트 포장 설계를 위한 재료적 기초 데이터를 제시하고자 한다.

• 조명전기설비학회논문지
• /
• 제23권8호
• /
• pp.26-32
• /
• 2009

접지시스템은 전기설비의 기준 전위점을 확보할 뿐만 아니라 대지에 낮은 저항으로 고장전류나 과도전류를 흐르게 한다. 주파수에 대한 함수로 접지 임피던스는 고장이나 과도전류가 넓은 범위의 주파수 성분을 포함하기 때문에 접지성능을 평가하는데 필요하다. 동봉은 배전계통에서 가장 많이 쓰이는 접지전극이다. 본 논문에서는 동봉의 접지 임피던스를 주파수 60[Hz] 에서 100[kHz] 범위까지 측정하여 등가 접지임피던스 모델을 구하였다. 뇌격서지가 유입되었을 때 EDSA 프로그램으로 과도접지임피던스의 수치와 파형을 시뮬레이션 하였다.

• 열처리공학회지
• /
• 제23권1호
• /
• pp.23-28
• /
• 2010

The cylindrical magnetron sputtering has not been widely used, although this system is useful for only certain types of applications such as fiber coatings. This paper presents electrode configurations which improved the complicacy of the target assembly by using the positive voltage power supply. It is a modified type which has a target constructed with a large cylindrical part, a conical part and a small cylindrical part. When positive voltage was applied to an anode, a stable glow discharge was established and a high deposition rate was obtained. The substrate bias current was monitored to estimate the effect of ion bombardment. As a result, it was found that the substrate current was large. With cylindrical and conical cathode magnetron sputter deposition on the surface of the substrate to prevent re-sputtering, ion impact because it can increase the effectiveness with excellent ductility and adhesion of Ti film deposition can be obtained. We board at the front end of the ground resistance of $5\;k{\Omega}$ attached to the substrate potential can be controlled easily, and Ti film deposition with excellent adhesion can be obtained. Microstructure and morphology of Ti films deposited on pure Cu wires were investigated by scanning electron microscopy in relation to preparation conditions. High level ion bombardment was found to be effective in obtaining a good adhesion for Cu wire coatings.

• 정보과학회 논문지
• /
• 제44권6호
• /
• pp.559-565
• /
• 2017

무인항공기는 사람이 탑승하지 않고 미리 설계된 프로그램에 따라 동작하기 때문에 전자기 간섭 등의 외부 영향에 대해 높은 신뢰성을 요구한다. 하지만 소형 무인항공기는 무게 및 공간의 제약으로 인해 외부 영향에 대해 물리적으로 완벽한 저항성을 가지도록 만들기가 어렵다. 이러한 여건으로 인해 기존에 운용 중인 소형 무인항공기는 외부 영향으로 비행제어 컴퓨터가 재시작 될 경우 비행체가 추락하는 상황이 발생하기도 하였다. 따라서 본 논문에서는 소형 무인항공기 비행안전성 향상을 위한 비행제어컴퓨터 알고리즘을 제안한다. 제안하는 알고리즘은 3개의 단계로 이루어져 있다. 첫 번째 단계는 항법장비를 교정하고 유효성을 검증하는 것이다. 두 번째 단계는 이륙단계에 교정데이터를 저장하는 것이다. 세 번째 단계는 비행제어컴퓨터 재시작 발생 시 현재 비행 상태를 판단하고, 비행 중일 경우에 교정데이터를 복구하는 것이다. 제안하는 알고리즘을 실제 소형 무인기에 적용하여 시험한 결과 비행제어컴퓨터가 재시작 되는 상황에도 안전하게 비행 유지가 가능함을 확인할 수 있었다.

• Geomechanics and Engineering
• /
• 제11권3호
• /
• pp.385-400
• /
• 2016

Bearing capacity of open-ended piles depends largely on inner frictional resistance, which is influenced by the degree of soil plugging. While a fully-plugged open-ended pile produces a bearing capacity similar to a closed-ended pile, fully coring (or unplugged) pile produces a much smaller bearing capacity. In general, open-ended piles are driven under partially-plugged mode. The formation of soil plug may depend on many factors, including wall thickness at the pile tip (or inner pile diameter), sleeve height of the thickened wall at the pile tip and relative density. In this paper, we studied the effects of wall thickness at the pile base and sleeve height of the thickened wall at the pile tip on bearing capacity using laboratory model tests. The tests were conducted on a medium dense sandy ground. The model piles with different tip thicknesses and sleeve heights of thickened wall at the pile tip were tested. The results were also discussed using the incremental filling ratio and plug length ratio, which are generally used to describe the degree of soil plugging. The results showed that the bearing capacity increases with tip thickness. The bearing capacity of piles of smaller sleeve length (e.g., ${\leq}1D$; D is pile outer diameter) was found to be dependent on the sleeve length, while it is independent on the sleeve length of greater than a 1D length. We also found that the soil plug height is dependent on wall thickness at the pile base. The results on the incremental filling ratio revealed that the thinner walled piles produce higher degree of soil plugging at greater penetration depths. The results also revealed that the soil plug height is dependent on sleeve length of up to 2D length and independent beyond a 2D length. The piles of a smaller sleeve length (e.g., ${\leq}1D$) produce higher degree of soil plugging at shallow penetration depths while the piles of a larger sleeve length (e.g., ${\geq}2D$) produce higher degree of soil plugging at greater penetration depths.

• Structural Engineering and Mechanics
• /
• 제39권3호
• /
• pp.427-447
• /
• 2011

The progressive collapse phenomenon is generally regarded as dynamic. Due to the impracticality of nonlinear dynamic computations for practitioners, an interest arises for the development of equivalent static pushover procedures. The present paper proposes a methodology to identify such a procedure for sudden column removals, using energetic evaluations to determine the pushover loads to apply. In a dynamic context, equality between the cumulated external and internal works indicates a vanishing kinetic energy. If such a state is reached, the structure is sometimes assumed able to withstand the column removal. Approximations of these works can be estimated using a static computation, leading to an estimate of the displacements at the zero kinetic energy configuration. In comparison with other available procedures based on such criteria, the present contribution identifies loading patterns to associate with the zero-kinetic energy criterion to avoid a single-degree-of-freedom idealisation. A parametric study over a family of regular steel structures of varying sizes uses non-linear dynamic computations to assess the proposed pushover loading pattern for the cases of central and lateral ground floor column failure. The identified quasi-static loading schemes are shown to allow detecting nearly all dynamically detected plastic hinges, so that the various beams are provided with sufficient resistance during the design process. A proper accuracy is obtained for the plastic rotations of the most plastified hinges almost independently of the design parameters (loads, geometry, robustness), indicating that the methodology could be extended to provide estimates of the required ductility for the beams, columns, and beam-column connections.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.53-58
• /
• 2002

Electrical insulation and mechanical properties of the plasma sprayed oxide ceramic coatings were studied before and after the sealing treatment of the ceramic coatings. Plasma sprayed A1$_2$O$_3$-TiO$_2$ coating as the reference coating was sealed using three commercial sealants based on polymer. Penetration depth of the sealants to the ceramic coating was evaluated directly from the optical microscope using a fluorescent dye. It is estimated that the penetration depth of the sealants to the ceramic coating is from 0.2 to 0.5 mm depending on the sealants used. The preliminary test results with a DC puncture tester imply that the dielectric breakdown voltage mechanism of plasma sprayed ceramic coatings has been determined to be a corona mechanism. Dielectric breakdown voltage of the as-sprayed and as-ground samples have shown a linear trend with regard to the thickness showing an average dielectric strength of 20 kV/mm for the thickness scale studied. It is also shown that grinding the coating before sealing and adding fluorescent dye do not agent the penetration depth of sealants. All of the microhardness, two-body abrasive wear resistance, bond strength, and surface roughness of the ceramic coating after the sealing treatment are improved. The extent of improvement is different from the sealants used. However, three-point bending stress of the ceramic coating after the sealing treatment is decreased. This is attributed to the reduced micro-crack toughening effect since the cracks propagate easily through the lamellar of the coating without crack deflection and/or branching after the sealing treatment.

• 한국컴퓨터정보학회논문지
• /
• 제17권11호
• /
• pp.33-38
• /
• 2012

미도는 문 스펜서가 제시한 이론으로 아름다움의 정도를 수치로 표현하려 한 것이다. 그리고 미국의 학자 버크호프가 문 스펜서의 미는 복잡성 속의 질서성을 가진 것이라는 명제를 분석하였다. 그는 미도의 공식을 발표하여 미도의 정도를 수량적으로 취급하였다. 따라서 기존의 색채 조화론의 부족한 점을 제거하여 보다 과학적이고 정량적인 조화이론을 전개했다. 본 논문에서는 배색의 좋고 나쁨은 질서의 요소와 복잡함의 요소로 나누었다. 미도는 질서의 요소를 복잡함의 요소로 나눈 것이다. 이를 영상의 미도 계산에 활용하여, 감성으로 취급되는 색채조화 및 부조화의 문제를 수치적으로 계산하였다. 그리하여 영상에서 색을 판별하여 미도가 좋은 배색인지 아닌지를 나타내었다.