• Asian Oncology Nursing
• /
• v.11 no.3
• /
• pp.179-185
• /
• 2011

Purpose: This study analyzed recent trends of instrument usage assessing cognitive function of breast cancer patients undergoing chemotherapy. Methods: The researcher collected 64 studies outside the country that were published between January 1996 and August 2010. Results: There was no study on the instrument assessing all domains of cognitive function in breast cancer patients undergoing chemotherapy. Most instruments assessing cognitive function of breast cancer patients have been used for patients with dementia, depression, and/or organic brain damage. Also the objective neuropsychological tests such as the grooved pegboard for the psychomotor area, RCFT copy in visuospatial skill area and the WAIS-III block design have low sensitivity for measuring cognitive function in breast cancer patients, thus they are not good for applying to breast cancer patients. Conclusion: There is a need to develop an instrument which has good sensitivity and specificity for measuring the cognitive function of the breast cancer patients who experienced cognitive impairment after chemotherapy treatment. In addition, the developed instrument needs to be accessible and feasible in any nursing clinical setting for the purpose of accurate assessment and evaluation of the cognitive function among breast cancer patients.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.12
• /
• pp.1646-1654
• /
• 2002

A two-phase closed thermosyphon was one of the most effective devices in the removing heat because of its simple structure, thermal diode characteristics, wide operating temperature range and so on. In this study, a two-phase closed thermosyphon(working fluid PFC(C6F14), container copper(inner grooved surface)) was fabricated with a reservoir which can change the fill charge ratio. The experiments were performed in the range of 50~600W heat flow rate and 10~70% fill charge ratio. The results were compared with some correlations that were presented by Rohsenow and Immura et al. in the evaporator, by Nusselt, Gross and Uehara et al. in the condenser and by Cohen and Bayley, Wallis, Kutateladze and Faghri et al. in heat transfer limitation etc.. The heat transfer coefficient at the evaporator increased with the input power. However the effect of the fill charge ratio was nearly negligible. At the condenser, it showed an opposite trend to the evaporator and with increase of the fill charge ratio, showed some enhancement of heat transfer. The heat transport limitation was occurred by the dry-out limitation for small fill charge ratio(10%) and presented about 100W. For the case of large fill charge ratio(Ψ$\geq$40%), it was occurred by the flooding limitation at about 500W.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.5
• /
• pp.171-176
• /
• 2001

Plasma Display Panel(PDP) is a type of flat panel display utilizing the light emission produced by gas discharge. Barrier Ribs of PDP separating each sub-pixel prevents optical and electrical crosstalks from adjacent sub-pixels. Mold for forming barrier ribs has been newly researched to overcome the disadvantages of conventional manufacturing process such as screen printing, sand-blasting and photosensitive glass methods. Mold for PDP barrier ribs have stripes of micro grooves transferring glass-material wall. In this paper, Stripes of grooves of which width 48${\mu}{\textrm}{m}$ and 270${\mu}{\textrm}{m}$, depth 124${\mu}{\textrm}{m}$, pitch 274${\mu}{\textrm}{m}$ was acquired by machining hard and brittle materials of WC, Silicon, Alumina with dicing saw blade. Maximum roughness of the bottom and sidewall of the grooves was respectively 120nm, 287nm in grooving WC. Maximum tilt angle caused by difference between upper-most width and lower-most width was 2$^{\circ}$. Maximum Radius of bottom curvatures was 7.75${\mu}{\textrm}{m}$. This results satisfies the specification for barrier ribs of 50 inch XGA PDP if the groove form of mold was fully transferred to the barrier ribs. Barrier ribs were formed with Silicone rubber mold, which is transferred from grooved hard materials. Silicone rubber mold has elasticity accommodating the waveness of lower glass plate of PDP.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.4 s.193
• /
• pp.115-122
• /
• 2007

Recently, remarkable progress has been made in both technology and production of optical elements including aspheric lens. Especially, requirements for machining glass materials have been increasing in terms of limitation on using environment, flexibility of material selection and surface accuracy. In the past, precision optical glass lenses were produced through multiple processes such as grinding and polishing, but mass production of aspheric lenses requiring high accuracy and having complex profile was rather difficult. In such a background, the high-precision optical GMP process was developed with an eye to mass production of precision optical glass parts by molding press. This GMP process can produce with precision and good repeatability special form lenses such as camera, video camera, aspheric lens for laser pickup, $f-\theta$ lens for laser printer and prism, and me glass parts including diffraction grating and V-grooved base. GMP process consist a succession of heating, forming, and cooling stage. In this study, as a fundamental study to develop molds for GMP used in fabrication of glass lens, we conducted a glass lens forming simulation. In prior to, to determine flow characteristics and coefficient of friction, a compression test and a compression farming simulation for PBK40, which is a material of glass lens, were conducted. Finally, using flow stress functions and coefficient of friction, a glass lens forming simulation was conducted.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.88-88
• /
• 2011

복합분자펌프는 기존의 터보분자펌프 turbine blade에 spiral grooved를 추가하여 초고진공(10-8 Pa)에서 저진공(330Pa)까지 넓은 압력범위에서 사용할 수 있고 이 펌프를 사용함으로서 완전 oil free한 진공시스템을 만들 수 있는 특징을 가지고 있다. 특히, 회전체를 비접촉으로 지지하는 자기베어링 방식을 적용함으로써, 진동은 극히 작고 베어링수명은 길면서 중저진공에 대한 배기속도가 크고 임의의 방향으로 접속이 가능하여 반도체 및 디스플레이 제조 공정과 같은 첨단산업의 다양한 분야에 쉽게 적용되고 있으며, 그 적용 분야와 시장은 계속 성장하고 있다. 고 진공과 배기 속도의 달성을 위해서, 고속으로 이동하는 격면과 기체분자를 충돌시켜, 기체 분자를 원하는 방향으로 유도하는 작동원리를 가지고 있다. 특히 공기분자의 밀도가 매우 낮은 희박가스 상태에서 고속 회전하는 blade로 공기분자를 쳐 내면서 작동됨으로써 날개의 상하 압력차에 의한 공기력보다도 날개의 고속회전이 매우 중요시 되고 압력으로는 10-1 Pa 이하의 분자영역에서 그 성능을 최고로 발휘 할 수 있다. 이러한 복합 펌프의 주요 장점은 다음과 같다. 1. 10-8 Pa (10-10torr)~10 Pa (1 torr) 까지 넓은 영역에서 배기가 가능하다. 2. 탄화수계의 대하여 높은 압축특성을 가지고 있고, 윤활유를 사용하지 않으므로 얻을 수 있는 진공상태가 고청정하다(oil free). 3. 정밀 5축제어 자기베어링으로 완전히 부상하여 회전함으로서 마모가 없고 진동이 최소화하였을 뿐만 아니라, 또한 운전음도 거의 없다. 4. 설치조건에 제한이 없고 고장이 거의 없다. 본 논문에서는 이러한 복합분자펌프의 개발을 위하여, 상기 연구기관에서 수행된 내용을 소개하고 있으며, 펌프 시스템의 기본 설계 및 자기베어링 시스템의 설계 결과 및 수치해석 결과를 나타내었다.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.16 no.3 s.43
• /
• pp.335-344
• /
• 1992

This study was conducted to investigate the influence of addition of cetyl trimethyl ammo­nium bromide (CTAB), and amine [ethylamine (EA) or ethylene diamine (EDA)] to aqueous sodium hydroxide (NaOH) solution on polyester alkaline hydrolysis, The experimental vari­ables such as CTAB concentration, EA or EDA concentration, NaOH concentration, tempera­ture and time were compared, and the changes in physical and chemical properties of alkaline­hydrolyzed PET fabrics depending on their treated conditions were measured, The results are as follows: 1. By adding CTAB and amine in aqueous NaOH solution, increasing effect on weight loss of PET fabrics was obtained in simultaneous addition of CTAB and EDA, but not in CTAB and EA. 2. By adding CTAB & EDA simultaneously, increasing effect on weight loss was obtained regardless of EDA concentration, time and temperature, and it was more effective at lower NaOH concentration. :l. The increase of void space (or irregularly grooved surface), of softness, of wickability, of dyeability on PET fabric, and the decrease of tensile strength, of molecular weight were observed according to the weight loss on the PET fabrics. These changes were equal to all alkaline-hydrolyzed PET fabrics regardless of addition of CTAB and amine. l. There was little changes on crystallinity, thermal behavior when PET fiber was treated with ,aqueous NaOH solution with CTAB and EDA. These results supported that increasing effect on weight loss take place without inducing of fine structural change of PET fibers.

• The Korean Journal of Cytopathology
• /
• v.2 no.2
• /
• pp.153-159
• /
• 1991

Langerhans' cell histiocytosis (LCH), known for histiocytosis X, is a clinicopathologic entity characterized by proliferation of Langerhans' cells (LCs) throughout the body including the reticuloendothelial system, bone, and skin. LCs is currently considered as a distinct type of histlocytic cells, not primarily phagocytic in nature. Recently, we could make the diagnosis on cytologic specimen in a 3 month-old-boy and a 3 year-old-boy. The cases were diagnosed on scraping smear from the skin and fine needle aspiration cytology from the lymph node, respectively. The characteristic cytologic features of Langerhans' cells were noted in the nuclei, namely eccentric, indented, elongated, and grooved nuclei. The cells also had abundant and acidophilic cytoplasm. The cytologic diagnoses were confirmed on the biopsies from the skin and lymph node, respectively.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.34 no.2
• /
• pp.212-222
• /
• 1998

Heat transfer performance improvement by fin and groovs is studied for condensation of R-11 on integral-fin tubes. Eight tubes with trapczodially shaped integral-fins having fin density from 748 to 1654fpm(fin per meter) and 10, 30 grooves are tested. A plain tube having the same diameter as the finned tubes is also used for comparison. R-11 condensates at saturation state of 32 $^{\circ}C$ on the outside tube surface coded by inside water flow. All of test data are taken at steady state. The heat transfer loop is used for testing singe long tubes and cooling is pumped from a storage tank through filters and folwmeters to the horizontal test section where it is heated by steam condensing on the outside of the tubes. The pressure drop across the test section is measured by menas pressure gauge and manometer. The results obtained in this study is as follows : 1. Based on inside diameter and nominal inside area, overall heat transfer coefficients of finned tube are enhanced up to 1.6 ~ 3.7 times that of a plain tube at a constant Reynolds number. 2. Friction factors are up to 1.6 ~ 2.1 times those of plain tubes. 3. The constant pumping power ratio for the low integral-fin tubes increase directly with the effective area to the nominal area ratio, and with the effective area diameter ratio. 4. A tube having a fin density of 1299fpm and 30 grooves has the best heat transfer performance.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.2
• /
• pp.67-72
• /
• 2007

High Pressure Micro Jet (HPMJ) pad conditioning system was investigated as an alternative to diamond disc conditioning in copper CMP. A series of comparative 50-wafer marathon runs were conducted at constant wafer pressure and sliding velocity using Rohm & Haas IC1000 and Asahi-Kasei EMD Corporation (UNIPAD) concentrically grooved pads under ex-situ diamond conditioning or HPMJ conditioning. SEM images indicated that fibrous surface was restored using UNIPAD pads under both diamond and HPMJ conditioning. With IC1000 pads, asperities on the surface were significantly collapsed. This was believed to be due to differences in pad wear rates for the two conditioning methods. COF and removal rate were stable from wafer to wafer using both diamond and HPMJ conditioning when UNIPAD pads were used. Also, HPMJ conditioning showed higher COF and removal rate when compared to diamond conditioning for UNIPAD. On the other hand, COF and removal rates for IC1000 pads decreased significantly under HPMJ conditioning. Regardless of pad conditioning method adopted and the type of pad used, linear correlation was observed between temperature and COF, and removal rate and COF.

• Restorative Dentistry and Endodontics
• /
• v.17 no.2
• /
• pp.365-382
• /
• 1992

The purpose of this study was to evaluate the adaptation of filling material to the dentinal walls of root canals with and without smear layer. Fifty extracted upper and lower anterior teeth were selected, and the root canals were instrumented with K - files 1mm short of the apical foramen by step - back method. The teeth were randomly divided into two groups of 25 each : in the group I, smear layers were not removed, and in the group II, smear layers were removed by 15% EDTA solution. Again the two groups 25 teeth were randomly divided into unfilled contol group and filling groups(lateral, ultrasonic, ULTRAFIL, McSpadden compaction group). Upon completion of root canal filling, the teeth were grooved on the both the labial and lingual surfaces and then split with mallet and chisel. Each specimens were examined with JSM - 840 Scanning Electron Microscope (JEOL., Japan). The results were as follows : 1. In the contol group, dentinal tubules of group I couldn't be distinguished in the canal wall, but those of group II appeared to be open and patent. 2. In the filling groups of group I, the tubular penetration of the sealer or gutta percha couldn't be seen, but in the filling groups of group II, it could be seen except McSpadden compaction group. 3. In the filling groups, ULTRAFIL group showed the best adaptation of filling material to root canal wall among the group I, and lateral and ultrasonic condensation group showed the best adaptation of filling material among the group II. McSpadden compaction group showed the worst adaptation in group I, II. 4. Generally, the group II showed better adapation of filling material to root canal wall than the group I.