• Journal of Technologic Dentistry
• /
• v.28 no.1
• /
• pp.9-17
• /
• 2006

The purpose of this study was to evaluate the titanium castability with a spin type casting machine(TiCast, Super R, Selec, Osaka. Japan). We tested phosphate bonded investment "Rematitan$^{(R)}$Plus(Dentaurum, Inc., Pforzheim, Germany)"of mesh grid pattern and plate pattern. Four different mold temperatures(room temperature, 200$^{\circ}C$, 400$^{\circ}C$ and 600$^{\circ}C$) were prepared for the present study. In mesh grid pattern with spruing of $\varphi$0.88㎜ dimeter, when the mold temperature increased, high percentage of castability was gained. Mold temperature showed a highly significant(p<0.05) correlation on the castability, In plate pattern, the higher the mold temperature during casting, the greater the adhesive phenomenon between Ti surface and the investment.

• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.73-76
• /
• 2003

This paper proposes a maximum output power control of grid-connected wind power generation system using cage-type induction generators. For generator control, indirect vector control is used, where d-axis current controls the excitation level and q-axis current controls the generator speed. The generated power flows into the utility through the grid-side converter, by which the do link voltage is controlled to be constant and the ac current is controlled in sinusoid and. The generator speed is adjusted according to wind speed for extracting maximum power generation. Experimental results are shown to verify the validity of the proposed scheme.

• Journal of Ocean Engineering and Technology
• /
• v.14 no.1
• /
• pp.52-59
• /
• 2000

Flexural fracture characteristics of newly-developed Grid-type carbon fiber plastics in the deteriorated reinforced concrete structures were investigated by the four-points fracture test to verify the strengthening effects in the beam specimens. Results showed that initial cracks appeared in the boundary layers of fibers embedded in the newly-placed mortar concrete slowly progressed to the direction of supports and showed fracture of fiber plastics and brittle failure of concrete in compression in sequence after the yielding of steel reinforcement. Accordingly the reasonable area of Grid-type carbon-fiber plastics in the strengthening design of deteriorated RC structures should be limited and given based on the ultimate strength design method to avoid the brittle failure of concrete structures.

• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2333-2335
• /
• 1998

Recently, the development of computer achieves a system which is similar to the mechanics of human visual system. The 3D measurement using monocular vision system must be achieved a camera calibration. So far, the camera calibration technique required reference target in a scene. But, these methods are inefficient because they have many calculation procedures and difficulties in analysis. Therefore, this paper proposes a native method that without reference target in a scene. We use the grid type frame with different line widths. This method uses vanishing point concept that possess a rotation parameter of the camera and perspective ration that perfect each line widths into a image. We confirmed accuracy of calibration parameter estimation through experiment on the algorithm with a grid paper with different line widths.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.7
• /
• pp.1372-1377
• /
• 2011

This paper proposes the control method of MPPT(maximum power point tracking) for the wind energy generation system using the duty ratio control of boost type DC-DC converter. For a lower cost and a higher reliability, the wind and the generator velocity sensors are removed. MPPT control is implemented by changing the duty ratio of the boost converter. Chain rule is applied by using each function. The grid side inverter is controlled to regulate unity power factor. The proposed control method was analyzed mathematically and verified by the computer simulation using PSIM.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.359-360
• /
• 2015

10kV IGCT has been recently developed and has the potential to push wind turbine systems to higher power and voltage rating. Converters employing IGCTs need snubber and OVP circuit to limit the rate of rise of current and peak over voltage across IGCT during turn on and off state respectively. The conventional RCD snubber which is used in such power converter dissipates a significant amount of power. In order to reduce the amount of energy lost by conventional RCD snubber, this paper proposes an isolated inductor snubber circuit that not only meets all of the IGCTs characteristics during on and off-state but also significantly saves the power loss. Loss analysis of conventional di/dt snubber and OVP circuit is performed for the 3-level NPC type back-to-back VSC supplied from grid voltage of 6.9kV. In comparison with the conventional snubber, isolated inductor snubber has a fewer number of components and improved efficiency leading to a reliable and efficient wind turbine systems.

• Transactions of Materials Processing
• /
• v.33 no.2
• /
• pp.123-131
• /
• 2024

Plastic, the main material of FFF-type 3D printing, exhibits lower strength compared to metal. research aimed at increasing strength is needed for use in various industrial fields. This study analyzed three X-shape infill patterns(grid, lines, zigzag) with similar internal lattice structure. Moreover, tensile test considering weight and printing time was conducted based on the infill line multiplier and infill overlap percentage. The three X-shape infill patterns(grid, lines, zigzag) showed differences in nozzle paths, material usage and printing time. When infill line multiplier increased, there was a proportional increase in tensile strength/weight and tensile strength/printing time. In terms of infill overlap percentage, the grid pattern at 50% and the zigzag and lines patterns at 75% demonstrated the most efficient performance.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.10
• /
• pp.1738-1743
• /
• 2008

Environmental issue is one of the key factors to industry area using fossil fuels, because it accelerates the global warming. So it is supposed to reduce greenhouse gases around the developed nations of the world at times go. This issue is especially for the power industry. Under this background, MicroGrid system that consists of Distributed Energy Resources (DER) system, such as natural power system (wind, solar) and fuel-cell, co-generation, also known as CHP (Combined heat and power), has been developed greatly during the last 10 years. This paper adopts optimal model using GAMS to develop methods for conducting an integrated assessment of MicroGrid system.

• Proceedings of the Korean Society for Bioinformatics Conference
• /
• 2004.11a
• /
• pp.13-20
• /
• 2004

Grid system has the potential to resolve the current need of bioinformatics for super-computing environment inexpensively. There are already several Grid applications of bioinformatics tools. To solve the real-world bioinformatics problems, however, the various integration of each tool is necessary in addition to the implementation of more basic tools. Workflow based problem solving environment can be the efficient solution for this type of software development. There are still heavy overhead, however, to develop and implement workflow model on current Grid system. He re we propose a model of simple problem solving environment that enables component based workflow design of integrated bioinformatics applications on Grid environment by using Condor functionalities. We realized this model for practical bioinformatics solutions of a genome sequence analysis and a comparative genome analysis. We implemented necessary bioinformatics tools and interfacing tools as the components, and combine them in the workflow model of each solution by using the tools presented in Condor.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.1 s.14
• /
• pp.1-4
• /
• 2006

Recently, Ball Grid Arrays(BGAs) are getting used more frequently for a package type. The connectors on a BGA consist of a large number of small solder balls in a grid shape on its bottom side. However, since balls of BGAs mounted on PCBs are not visible, inspection before mounting them is indispensable. High speed non-contact 3D measurement technologies are necessary far real-time measurement of ball height, the most important inspection item. In this paper, an accurate 3D data acquisition system for BGAs is proposed that can acquire 3D profile at high speed using a 3D smart camera and laser slit ray projection. Some clipping and morphological filtering operations are employed to remove spiky error data, which occur due to reflections from some ball area to camera direction.