• International Journal of Aeronautical and Space Sciences
• /
• 제16권1호
• /
• pp.8-18
• /
• 2015

A numerical simulation for a nonslender BWB UCAV configuration with a rounded leading edge and span of 1.0 m was performed to analyze its aerodynamic characteristics. Numerical results were compared with experimental data obtained at a free stream velocity of 50 m/s and at angles of attack from -4 to $26^{\circ}$. The Reynolds number, based on the mean chord length, is $1.25{\times}106$. 3D multi-block hexahedral grids are used to guarantee good grid quality and to efficiently resolve the boundary layer. Menter's shear stress transport model and two transition models (${\gamma}-Re_{\theta}$ model and ${\gamma}$ model) were used to assess the effect of the laminar/turbulent transition on the flow characteristics. Aerodynamic coefficients, such as drag, lift, and the pitching moment, were compared with experimental data. Drag and lift coefficients of the UCAV were predicted well while the pitching moment coefficient was underpredicted at high angles of attack and influenced strongly by the selected turbulent models. After assessing the pressure distribution, skin friction lines and velocity field around UCAV configuration, it was found that the transition effect should be considered in the prediction of aerodynamic characteristics of vortical flow fields.

• 대한조선학회논문집
• /
• 제55권3호
• /
• pp.265-273
• /
• 2018

Direct numerical and large eddy simulations of transitional flows around studs installed on flat plate and bulbous bow have been performed to investigate an effectiveness of turbulence stimulators on laminar-to-turbulence transition at a very low speed. The flow velocity was determined to be 0.366m/s corresponding to 4 knots of full-scale ship speed when the objective ship was Kriso container ship. The spatial evolution of skin friction coefficient disclosed that a fully development of turbulence was observed behind the second stud installed on flat plate while a rapid transition from laminar to turbulence gave rise to the fully development of turbulence behind the first stud installed on bulbous bow. A comparison of streamwise mean velocity profiles showed that the viscous sublayer and log-layer were in good agreement with previous results although the friction velocity of Smagrosinsky sub-grid scale model was about 10% larger than that of direct numerical simulation. While the turbulence intensities of bulbous bow was similar to those of flat plate in inner region, larger intensities of turbulence were observed in outer region of bulbous bow than those of flat plate.

• Archives of Plastic Surgery
• /
• 제36권3호
• /
• pp.283-288
• /
• 2009

Purpose: Frey's syndrome is a common complication after parotid surgery and characterized by gustatory sweating and flushing in the periauricular area during meals. Although a variety of methods have been proposed to prevent this postoperative problem but they have been unsatisfactory. In this article, therefore, botulinum toxin A was used to treat nine patients with Frey's syndrome and its duration effect after injection was investigated. Methods: Nine patients became the object of study about the effect of botulinum toxins as treatment of Frey's syndrome. Age of patients ranged from 25 to 78 years (mean, 43.7 years). Six of nine patients had both symptoms of gustatory sweating and flushing. And the others had only gustatory sweating symptom. Using Minor starch iodine test, the affected skin area was detected, and it was marked by $1cm^2$ sized grid appearance. After application of EMLA cream on the gustatory sweating area, botulinum toxin A was injected intracutaneously into the affected skin area ($2.5U/cm^2$). Patients were followed up from six to fifteen months (mean, about 12 months) and asked about improvement of their symptoms. Results: The treatement with botulinum toxin A took effective within two days after injection. Six months after injection, gustatory sweating disappeared completely in all patients, and five of six patients who had gustatory flushing improved in their symptom. Last follow-up, no patients complained of recurrent gustatory sweating and flushing except one. One patient, seven months after initial injection, was retreated with botulinum toxin A because of recurrence, and the result was successful. The duration of the effect after botulinum toxin A treatment was ranged from seven to thirteen months. One patient in our series experienced the upper eyelid weakness as adverse effect, but it improved spontaneously. Conclusion: Local injection of botulinum toxin A is an effective, safe and long - lasting method for treatment of Frey's syndrome. Hereafter, however, additional study will be required to evaluate the duration effect of botulinum toxin A according to frequency in use and dosage.

• 한국진공학회지
• /
• 제18권3호
• /
• pp.164-175
• /
• 2009

전산 유체 역학 코드를 사용하여 안테나 내장형 유도 결합 플라즈마 시스템의 가스 유동 특성, 전력 흡수, 전자 온도, 전자 밀도, 화학종의 분포에 대해서 살펴보았다. 복잡한 현실적 3차원 시스템에 대한 안정한 수치해의 도출을 위해서 최적화된 격자생성 전략을 구사하였으며, 이를 이용하여 플라즈마 질화 시스템을 한 예로 전력 흡수, 가스 유동, 전자 온도, 전자 밀도, 화학종의 분포를 분석하였다. 금속 노출형 안테나의 경우 전력 도입부 쪽에 전력 흡수의 불균형이 모델에서 예측되었으며 유전체피복 안테나의 한 예에서 전력 흡수 표피 깊이가 실제 보고된 값인 53 mm와 잘 일치하는 50 mm로 예측되었다. 또한 수소연료 전지 분리판을 위한 고속 질화 공정용 시스템의 모델링에서도 산업용 대량 처리 시스템에 적절한 다중 분리판의 장입 간격을 가스 유동, 활발한 질화종인 질소 원자와 질소 분자 이온의 농도를 근거로 예측하였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2003년도 춘계종합학술대회
• /
• pp.165-170
• /
• 2003

본 논문에서는 임의의 장면에도 얼굴 인식에 영향을 받지 않는 통합된 얼굴 인식 방법을 제안한다. 크기 정규화는 피부 색 분할과 log-poler 매핑 절차의 새로운 조합을 통하여 얻어지고, 주요 얼굴 구성 요소 분석은 자세 변화들을 처리하기 위하여 제안된 멀티 뷰 접근을 통해 이루어진다. 주어진 컬러 입력 이미지로부터 검출기는 얼굴을 원형 경계 안에 둘러싸고 코의 위치를 표시하며 다음 인식을 위해, 원형 경계 내에 배치하는 방사형 격자는 특징 벡터 코 중심에 두었다. 컬러로 분할된 영역의 폭으로서 얼굴의 크기를 평가하고, 추출된 특징 벡터는 평가된 크기에 의하여 정규화된 크기이다. 특징 벡터는 얼굴 인식을 위해 훈련된 신경망 분류자에게 입력된다. 시스템은 서로 다른 복합적인 배경에서 다양한 크기와 자세를 가진 20명의 얼굴 데이터 베이스를 사용하여 실험한 결과 얼굴 인식기의 수행능력은 매우 작은 크기의 얼굴 이미지 외에는 87%에서 92%의 평균 인식율을 얻을 수 있었다.

• 대한방사선치료학회지
• /
• 제1권1호
• /
• pp.63-69
• /
• 1985

High energy electron beams took effect for tumor radio-therapy, however, had a lot of problems in clinical application because of various conversion factors and complication of physical reactions. Therefore, we had experimentally studied the important properties of high energy electron beams from the linear accelerator, LMR-13, installed in Yonsei Cancer Center. The results of experimental studies on the problems in the 8, 10, 12 Mev electron beam therapy were reported as following. 1. On the measurements of the outputs and absorbed does, the ionization type dosimeters that had calibrated by $^{90}Sr$ standard source were suitable as under $3\%$ errors for high energy electrons to measure, but measuring doses in small field sizes and the regions of rapid fall off dose with ionization chambers were difficult. 2. The electron energy were measured precisely with energy spectrometer consisted of magnet analyzer and tele-control detector and the practical electron energy was calculated under $5\%$ errors by maximum range of high energy electron beam in the water. 3. The correcting factors of perturbated dose distributions owing to radiation field, energy and material of the treatment cone were checked and described systematically and variation of dose distributions due to inhomogeneous tissues and sloping skin surfaces were completely compensated. 4. The electron beams, using the scatters; i.e., gold, tin, copper, lead, aluminium foils, were adequately diffused and minimizing the bremsstrahlung X-ray induced by the electron energy, irradiation field size and material of scatterers, respectively. 5. Inproving of the dose distribution from the methods of pendulum, slit, grid and focusing irradiations, the therapeutic capacity with limited electron energy could be extended.

• 한국정보통신학회논문지
• /
• 제7권6호
• /
• pp.1312-1317
• /
• 2003

본 논문에서는 임의의 장면에도 얼굴 인식에 영향을 받지 않는 통합된 얼굴 인식 방법을 제안한다. 크기 정규화는 피부 색 분할과 log-polar 매핑 절차의 새로운 조합을 통하여 얻어지고, 주요 얼굴 구성 요소 분석은 자세 변화들을 처리하기 위하여 제안된 멀티 뷰 접근을 통해 이루어진다. 주어진 컬러 입력 이미지로부터 검출기는 얼굴을 원형 경계 안에 둘러싸고 코의 위치를 표시하며 다음 인식을 위해, 원형 경계 내에 배치하는 방사형 격자는 특징 벡터 코 중심에 두었다. 컬러로 분할된 영역의 폭으로서 얼굴의 크기를 평가하고, 추출된 특정 벡터는 평가된 크기에 의하여 정규화 된 크기이다. 특징 벡터는 얼굴 인식을 위해 훈련된 신경망 분류자에게 입력된다. 시스템은 서로 다른 복합적인 배경에서 다양한 크기와 자세를 가진 20 명의 얼굴 데이터 베이스를 사용하여 실험한 결과 얼굴 인식기의 수행능력은 매우 작은 크기의 얼굴 이미지 외에는 87%에서 92%의 평균 인식율을 얻을 수 있었다.

• Journal of Radiation Protection and Research
• /
• 제3권1호
• /
• pp.6-22
• /
• 1978

High energy electron beams took effect for tumor radio-therapy, however, had a lot of problems in clinical application because of various conversion factors and complication of physical reactions. Therefor, we had experimentally studied the important properties of high energy electron beams from the linear accelerator, LMR-13, installed in Yonsei Cancer Center. The results of experimental studies on the problems in the 8, 10, 12 Mev electron beam therapy were reported as following. 1. On the measurements of the outputs and absorbed doses, the ionization type dosimeters that had calibrated by $^{90}Sr$ standard source were suitable as under 3% errors for high energy electrons to measure, but measuring doses in small field sizes and the regions of rapid fall off dose with ionization chambers were difficult. 2. The electron energy were measured precisely with energy spectrometer consisted of magnet analyzer and tele-control detector and the practical electron energy was calculated under 5% errors by maximum range of high energy electron beam in the water. 3. The correcting factors of perturbated dose distributions owing to radiation field, energy and material of the treatment cone were checked and described systematically and variation of dose distributions due to inhomogeneous tissues and sloping skin surfaces were completely compensated. 4. The electron beams, using the scatterers; ie., gold, tin, copper, lead, aluminium foils, were adequately diffused and minimizing the bremsstrahlung X-ray induced by the electron energy, irradiation field size and material of scatterers, respectively. 5. Inproving of the dose distribution from the methods of pendulum, slit, grid and focusing irradiations, the therapeutic capacity with limited electron energy could be extended.

• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.262-270
• /
• 1987

본 논문에서는 Eulerian 좌표축에서 온도 경계층과 혼합된 비정상 경계층 유 동을 효과적으로 다룰 수 있는 좌표변환 방법과 수치해석 방법을 도입하였다. 이전 의 수치적 방법들은 축차적이며, 뒷정체점 부근의 경계층 두께가 시간과 더불어 지수 적으로 증가하므로, 격자점의 수를 경계층 두께의 증가에 따라 상당히 늘려 주어야 된 다. 그러나 여기에서는, 격자점의 수를 무리하게 늘릴 필요가 없으며 일반적인 비선 형 차분방정식을 정확도를 떨어뜨리지 않고 선형화시킴으로써 비축차적인 수치해들이 허용된다. 이런 선형화 방법은 Beam & Warming에 의해 최초로 압축성 Navier-Stokes 방정식에 사용되었고, Orlandi & Ferziger, Kim & Chang에 의해 경계층 유동에 확장되 었다.또한 뒷정체점 부근에서 경계층 두께의 증가로 인한, 격자점 증가의 필요를 피하기 위하여, 몇 가지 서로 다른 종류의 변환변수들을 시간과 공간에 따라 선별적으 로 사용하여 수치적인 경계층 두께가 거의 일정하도록 만들었다. 이와 같은 변환변 수들은 또한 쌍-포물선형인 현 지배방정식의 초기조건들을 쉽게 구할 수 있도록 허용 해 준다.

• Archives of Reconstructive Microsurgery
• /
• 제14권2호
• /
• pp.95-104
• /
• 2005

The aim of this study was to investigate the major vascular system to supply flap, flap survival rate and complications after flap elevation in order to evaluate possibility of the vascularized face/scalp allotransplantation. Forty New Zealand white rabbits were divided into two groups: control group and experimental group. Individuals of control group had a face/scalp composite unit which was composed of skin, subcutaneous tissue and platysma muscle, supplying by bilateral facial artery, temporal artery and auricular artery and draining by external jugular vein. After a flap was elevated, bilateral facial artery, temporal artery and auricular artery were ligated. On the other hand, those of experimental group had the same composite unit as control group with bilateral facial artery, temporal artery and auricular artery being not ligated. We had measured survival area of flaps of the sixteen individuals survived for four weeks in the control group and fourteen in the experimental group by Grid method. The mean survival durations of the flap were 3.7days in the control group, 20.0days in the experimental group. The significant differences in the mean survival durations and survival rate at the 28days were found between the control and experimental group (p<0.05). Mean values about the survival area's fractions of all were $1.3{\pm}4.%$ in the control group and $63.1{\pm}4.8%$ in the experimental group. Those of experimental group was significantly higher than control group statistically (p<0.05). The composite face/scalp flap which we have elevated, supplied by bilateral facial artery, temporal artery, auricular artery and drained by external jugular vein has flap viability enough to be transplanted after its elevation.