• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.1
• /
• pp.179-184
• /
• 2004

This paper presents an image segmentation algorithm to obtain the 3D body shape data that the grid pattern and the body contour lute in the background image are extracted using the new proposed hybrid method. The body contour line is extracted based on maximum biased anisotropic recognition(MaxBAR) algorithm which recognizes the most strong and robust edges in the image since the normal derivative at the edges is large, while the tangential derivatives can be small. The grid patterns within body contour lines are extracted by grid pattern detection (GPD). The body contour lilies and the grid patterns are combined. The consecutive run test based on heuristic method is used to link the disconnected line and reduce noise line. This proposed segmentation method is more effective than the conventional method which uses a gradient and a laplacian operator, verified with application two conventional method.

• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1664-1672
• /
• 2015

This paper proposes a series arc fault detection algorithm which incorporates peak voltage and harmonic current detectors for single-phase boost power factor correction (PFC) rectifiers. The series arc fault model is also proposed to analyze the phenomenon of the arc fault and detection algorithm. For arc detection, the virtual dq transformation is utilized to detect the peak input voltage. In addition, multiple combinations of low- and high-pass filters are applied to extract the specific harmonic components which show the characteristics of the series arc fault conditions. The proposed model and the arc detection method are experimentally verified through a boost PFC rectifier prototype operating under the grid-tied condition with an artificial arc generator manufactured under the guidelines for the Underwriters Laboratories (UL) 1699 standard.

• Journal of the Korean Solar Energy Society
• /
• v.26 no.1
• /
• pp.91-98
• /
• 2006

Islanding phenomenon of utility-connected photovoltaic power conditioning systems(PV PCS) can cause a variety of problems and must be prevented. If the real and reactive power supplied by PV PCS are closely matched to those of load, islanding detection by passive methods becomes difficult. The active frequency drift(AFD) method, called the frequency bias method, enables islanding detection by forcing the frequency of the voltage in the islanding to drift up or down. In this paper, non-detection zone(NDZ) of AFD is analyzed for the islanding detection method of utility-connected PV PCS by the simulation software tool PSIM.

• The Journal of Korean Association of Computer Education
• /
• v.11 no.3
• /
• pp.81-89
• /
• 2008

The failure occurrence of resources in the grid computing is higher than in a tradition parallel computing. Since the failure of resources affects job execution fatally, fault tolerance service is essential in computational grids. And grid services are often expected to meet some minimum levels of quality of service (QoS) for desirable operation. However Globus toolkit does not provide fault tolerance service that supports fault detection service and management service and satisfies QoS requirement. Thus this paper proposes fault tolerance service to satisfy QoS requirement in computational grids. In order to provide fault tolerance service and satisfy QoS requirements, we expand the definition of failure, such as process failure, processor failure, and network failure. And we propose resource scheduling service, fault detection service and fault management service and show implement and experiment results.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.8 no.6
• /
• pp.534-543
• /
• 2015

This paper proposes an Energy Theft Traceback Protocol(ETTP) based on Logging and Marking that can trace Energy Theft back in Smart Grid Environment. The ETTP consists of the following three phases. First, it classifies Energy Theft Type into Measurement Rejection and Data Fabrication by generating an Energy Theft Tree. Second, it detects an Energy Theft by using the Energy Theft Tree. Finally, it trace an Energy Theft back by using the Logging Table of a Router and the Marking Information of a Packet. The result of its simulation shows that the Detection Ratio of Energy Theft is estimated at 92% and the Success Ratio of Energy Theft Traceback at 93%. Therefore, the ETTP not only reduces such risk factors as Forgery and Tampering about Billing information but also provides safe and reliable Smart Grid environment.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.10
• /
• pp.73-82
• /
• 2015

This paper proposes an ripple reduction algorithm and analyzes the effects of offset and scale errors generated by voltage sensor while measuring grid voltage in grid-tied single-phase inverters. Generally, the grid-connected inverter needs to detect the phase angle information by measuring grid voltage for synchronization, so that the single-phase inverter can be accurately driven based on estimated phase angle information. However, offset and scale errors are inevitably generated owing to the non-linear characteristics of voltage sensor and these errors affect that the phase angle includes 1st harmonic component under using SRF-PLL(Synchronous Reference Frame - Phase Locked Loop) system for detecting grid phase angle. Also, the performance of the overall system is degraded from the distorted phase angle including the specific harmonic component. As a result, in this paper, offset and scale error due to the voltage sensor in single-phase grid connected inverter under SRF-PLL is analyzed in detail and proportional resonant controller is used to reduce the ripples caused by the offset error. Especially, the integrator output of PI(Proportional Integral) controller in SRF-PLL is selected as an input signal of the proportional resonant controller. Simulation and experiment are performed to verify the effectiveness of the proposed algorithm.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.2005-2006
• /
• 2011

Due to the advantages of small sizes, more I/O ports, etc., Ball Grid Array (BGA) has been used in the production of printed circuit board (PCB). However, BGA voids can degrade the performance of the board and cause failure. To automatically detect the voids in X-ray image, a novel blob filter that makes use of the local image gradient magnitude is proposed in this paper. The utilization of the local image gradient magnitude makes the proposed filter invariant to the image brightness, void shape, void position, and component interference. Furthermore, different sizes of box filters are employed to analyze the image in multi-scale, and as a result, the proposed blob filter is robust to void size. Experimental results show that the proposed method can obtain void detection accuracy up to 96.104% while keep low false ratio.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.11
• /
• pp.2645-2652
• /
• 2013

For a variety of vision systems such as car omni-directional surveillance systems and robot vision systems, many cameras have been equipped and used. In order to detect corners of grid pattern in AVM(Around View Monitoring) systems, after the non-linear radial distortion image obtained from wide-angle camera is corrected, corners of grids of the distortion corrected image must be detected. Though there are transformations such as Sub-Pixel and Hough transformation as corner detection methods for AVM systems, it is difficult to achieve automatic detection by Sub-Pixel and accuracy by Hough transformation. Therefore, we showed that the automatic detection proposed in this paper, which detects corners accurately from the distortion corrected image could be applied for AVM systems, by designing and implementing it, and evaluating its performance.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.1
• /
• pp.44-52
• /
• 2014

Leakage is an important factor to be considered for the management of underground water supply pipelines in a smart water grid system, especially if the pipelines are aged and buried under the pavement or various structures of a highly populated city. Because the exact detection of the location of such leaks in pipelines is essential for their efficient operation, a new methodology for leak location detection based on frequency band variation, windowing filters, and probability is proposed in this paper. Because the exact detection of the leak location depends on the precision of estimation of time delay between sensor signals due to leak noise, some window functions that offer weightings at significant frequencies are applied for calculating the improved cross-correlation function. Experimental results obtained by applying this methodology to an actual buried water supply pipeline, ~ 253.9 m long and made of cast iron, revealed that the approach of frequency band variation with those windows and probability offers better performance for leak location detection.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.3
• /
• pp.83-95
• /
• 2022

This paper proposes a system that performs object detection and distance estimation for application to autonomous vehicles. Object detection is performed by a network that adjusts the split grid to the input image ratio using the characteristics of the recently actively used deep learning model YOLOv4, and is trained to a custom dataset. The distance to the detected object is estimated using a bounding box and homography. As a result of the experiment, the proposed method improved in overall detection performance and processing speed close to real-time. Compared to the existing YOLOv4, the total mAP of the proposed method increased by 4.03%. The accuracy of object recognition such as pedestrians, vehicles, construction sites, and PE drums, which frequently occur when driving to the city center, has been improved. The processing speed is approximately 55 FPS. The average of the distance estimation error was 5.25m in the X coordinate and 0.97m in the Y coordinate.