• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.546-546
• /
• 2013

Zinc silicate ($Zn_2SiO_4$) has been identified as a suitable host material for a wide variety of luminescent activators, such as transition metal and rare earth elements. In particular, manganese-activated $Zn_2SiO_4$ exhibits highly efficient photoluminescenceand cathodoluminescence, which allows this material to be used in fluorescent lamps and display applications. In this study, we investigated the green and yellow luminescence from Mn-doped $Zn_2SiO_4$ thin films that were synthesized using radio frequency magnetron sputtering followed by annealing at $600{\sim}1,200^{\circ}C$ The refractive index of the $Zn_2SiO_4$: Mn films showed normal dispersion behavior. It was found that the $Zn_2SiO_4$: Mn films annealed at $800^{\circ}C$ ossessed a mixture of alpha and beta phases. The obtained photoluminescence spectrum consisted of two emission bands centered at 525 nm in the green range and 574 nm in the yellow range. The green luminescence originates from the divalent Mn ions in alpha phase of $Zn_2SiO_4$, while the yellow luminescence comes from the divalent Mn ions in beta phase. The films annealed at and above $900^{\circ}C$ xhibited only the alpha phase. The broad PL excitation band was observed ranging from 220 to 300 nm with a maximum at around 243 nm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.12
• /
• pp.781-786
• /
• 2015

It is necessary for ferrite sheets to be fabricated with high packing density for excellent electrical properties and high strength. In this study, the relationship between the warpage and the packing density of ferrite green sheet, was investigated with amount variation of organic additives. With 0.4 wt% of dispersant, the packing density was about 48% and warpage appeared 0.5~1.3 mm high. With 1.4 wt% of dispersant, the packing density increased up to 57% and warpage appeared 0.8~2.1 mm high. With high packing density, warpage appeared along the edges of specimen, while with low packing density, deformation appeared over whole specimen inhomogeneously. It is thought that inhomogeneous deformation after sintering came from the inhomogeneity in green sheet prepared with badly dispersed slurry. With good homogeneity in green sheet from well-dispersed slurry, isotropic shrinkage is thought to have occurred along the distance from center to edges of specimen during sintering.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.3
• /
• pp.841-846
• /
• 2011

New green host materials, 9-phenyl-3-(4-(1-phenyl-1H-benzo[d] imidazol-2-yl)phenyl)-9H-carbazole (3a) and 9-(naphthyl-2-yl)-3-(4-(1-phenyl-1H-benzo[d]imidazol-2-yl)phenyl)-9H-carbazole (3b), have been designed and synthesized by attaching the electron transporting benzimidazole moiety to the hole transporting carbazole unit. These compounds have similar HOMO, LUMO levels and band-gap characteristics compared with CBP (4,4'-di(N-carbazolyl)biphenyl). The fabricated green phosphorescent OLED with this 3a host shows much better device performances compared to CBP-based one. The current and power efficiency is enhanced at least by 60 percent at a given constant luminance of 1000 cd/$m^2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.32-35
• /
• 2006

For the white UV-LED applications, $Eu^{2+}$-activated calcium aluminium silicate phosphors were synthesized for the first time and the structures and luminescence characteristics of these phosphors were investigated. The phosphors in this study emitted blue. green or blue-green light depending on the starting materials for synthesis. In addition, the structure was also changed when the different starting materials were used. When CaO and $CaCO_3$ was used as a starting material. tetragonal $Ca_2Al_2SiO_7$ was formed and blue-green and pure green light was emitted. respectively. However. in the case of $CaSiO_3$, triclinic $CaAl_2Si2O_8$ was formed and only pure blue emission was detected. The maximum emission intensity was obtained from $CaAl_2Si_2O_8:Eu^{2+}$ phosphors, which intensity was about 1.4 times higher than that of YAG:$Ce^{3+}$ phosphor used for blue LED.

• Prospectives of Industrial Chemistry
• /
• v.17 no.2
• /
• pp.8-20
• /
• 2014

나노세공체는 고표면적, 균일한 다공성, 분자크기의 세공구조, 높은 흡착용량, 이온교환 특성, 높은 촉매활성, 분자크기의 형상선택성 등의 특징을 갖기 때문에 촉매 및 흡착제로 나노소재 분야에서 가장 오랫동안 활용되어 왔던 중요한 물질 가운데 하나로 정유 및 석유화학 산업을 비롯한 화학산업과 환경 산업에 광범위하게 사용되고 있다. 본 고찰에서는 결정성 나노세공체 가운데 가장 중요한 제올라이트와 최근 연구가 활발한 하이브리드 나노세공체의 산업적 응용 및 기술개발 동향과 향후 발전 전망에 대해 간략히 기술하였다.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.06a
• /
• pp.13-17
• /
• 1997

The densification of $Al_2$O$_3$/15v/o ZrO$_2$ (Zirconia Toughened Alumina: ZTA) to the 99% of theoretical density was attempted by controlling the processing parameters affecting the each processing step i.e., milling, spray-drying, forming and pressureless sintering. The ZTA processed under the identical conditions showed a large variation in the green and sintered densities, and the mechanical properties. The deviation of 4-point bending strength was more than 100MPa for the ZTA with ~99% of theoretical density. Moreover, the relative green and sintered densities were deviated greatly from the average value. This low reproducibility could be caused by the variation of spray-dried granule properties. Thus, the effect of yield strength and morphology of spray-dried ZTA granule on the green and sintered densities and the mechanical properties needs to be studied in detail. The objective of this work is to fine out the optimum condition of compaction pressure and compaction method depending on the properties of spray-dried granules.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.6
• /
• pp.1957-1964
• /
• 2011

Various reaction conditions uding temperature, time and type and concentration of templates have been changed in order to facilely synthesize, especially with microwave (MW) heating, SAPO-34 molecular sieves. SAPO-34 molecular sieve can be synthesized rapidly with microwave irradiation from a gel containing tetraethylammonium hydroxide (TEAOH) as a template. However, other several templating molecules lead to SAPO-5 molecular sieve under microwave irradiation even though SAPO-34 is obtained by conventional electric synthesis from the same reactant gels. Moreover, SAPO-34 can be obtained more easily by increasing the TEAOH or silica concentration or by increasing the reaction temperature. SAPO-34 can be obtained within 5 min in a selected condition (high temperature of 210 $^{\circ}C$) with microwave heating, which may lead to a continuous production of the important material. SAPO-34 synthesized by microwave irradiation is homogeneous and small in size and shows acidity and a stable performance in the dehydration of methanol and 2-butanol to olefins, suggesting potential applications in acid catalysis.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.13 no.4
• /
• pp.25-32
• /
• 2013

The green building is one of biggest factors to go the goal of energy saving and environmental conservation, reduction of energy consumption, friendly energy technology, recycling of resource, and environmental pollution reduction technology. The purpose of these green buildings realized by the energy-saving technology such as the exterior materials or curtain wall system. The curtain wall system is a element that come to insulated portions of building envelope that results in heat loss. The purpose of this paper is to carried out mock-up tests for exterior wall used in autoclaved lightweight concrete panels in green building practices. Mock-up test execute a mixed process between standard test procedure and complex test procedure based on AAMA 501(American Society for Testing and Materials) and ASTM 283, ASTM 330(American Society for Testing and Materials). In results, tests meet the requirements that grant values in steps of procedures provided on ASTM and AAMA. ALC panel is suitable for a exterior wall product to be gratified thermal cycling performance and structural capacity, deflection(H/200) and lateral displacement(H/50), for curtain walls.

• Journal of Powder Materials
• /
• v.24 no.5
• /
• pp.400-405
• /
• 2017

The addition of a large amount of alloying elements reduces the compactibility and increases the compacting pressure, thereby shortening the life of the compacting die and increasing the process cost of commercial PM steel. In this study, the characteristic changes of Fe-Mo-P, Fe-Mn-P, and Fe-Mo-Mn-P alloys are investigated according to the Si contents to replace the expensive elements, such as Ni. All compacts with different Si contents are fabricated with the same green densities of 7.0 and $7.2g/cm^3$. The transverse rupture strength (TRS) and sintered density are measured using the specimens obtained through the sintering process. The sintered density tends to decrease, whereas the TRS increases as the Si content increases. The TRS of the sintered specimen compacted with $7.2g/cm^3$ is twice as high as that compacted with $7.0g/cm^3$.

• Journal of Sensor Science and Technology
• /
• v.24 no.3
• /
• pp.208-213
• /
• 2015

The purpose of this study is to optimize the design of a capacitive pressure sensor element using the simulation of electrical characteristics. The simulation of the ceramic sensor diaphragm ($Al_2O_3$) was performed by permitting pressure to change the curvature of the diaphragm. The pressure capacitance ($C_P$) was increased from 19.63 pF to 15.26 pF by applying pressure because the distance between the electrodes has been changed from $30{\mu}m$ to $15{\mu}m$. When the thickness of the diaphragm was changed to 0.46~0.52 mm, a larger capacitance change showed in accordance with the reduced thickness, which means an increase of sensitivity. However, considering the viewpoint of the signal linearity, it was selected for the optimum thickness of the diaphragm to 0.50 mm. The designed sensor element based on simulated results was tested to measure the output characteristics. Comparing of simulated and measured results, there was a margin of error of approximately 2%.