• Earthquakes and Structures
• /
• v.26 no.3
• /
• pp.229-237
• /
• 2024

This paper studied the subgrade spring stiffness and its influencing factors in the seismic deformation method of circular tunnel. Numerical calculations are performed for 3 influencing factors: stratum stiffness, tunnel diameter and burial depth. The results show that the stratum stiffness and tunnel diameter have great influence on the subgrade spring stiffness. The subgrade spring stiffness increases linearly with stratum stiffness increasement, and decreases with the tunnel diameter increasement. When the burial depth ratio (burial depth/tunnel diameter) exceeds to 5, the subgrade spring stiffness has little sensitivity to the burial depth. Then, a proposed formula of subgrade spring stiffness for the seismic deformation method of circular tunnel is proposed. Meanwhile, the internal force results of the seismic deformation method are larger than that of the dynamic time history method, but the internal force distributions of the two methods are consistent, that is, the structure exhibits elliptical deformation with the largest internal force at the conjugate 45° position of the circular tunnel. Therefore, the seismic deformation method based on the proposed formula can effectively reflect the deformation and internal force characteristics of the tunnel and has good applicability in engineering practice.

• Asian Journal of Turfgrass Science
• /
• v.4 no.1
• /
• pp.49-55
• /
• 1990

Experiments were conducted to investigate the relationships between the soil freezing depth and the accumulated degree-day of temperature below $0^{\circ}C$ at 17 locations during 1989-1990 winter season in kangwon province. The observed results are as follows : 1.When accumulated degree-day of temperature below at was 141t at late January soil freezing depth of sunny place was 46.5cm, that of shaded lot was 59 cm, and that of marginal place sunny or shaded area was 55cm, in Chun cheon. 2.Accumulated degree-day of temperature below at of Dae gwangryong area was more than that of Un-du, whereas soil freezing depth of Dae gwangryong was lower that of Un-du. It was considered that snow covering worked as heat insulator. 3.Soil freezing depth of vinyl mulching on Zoysia turf was less by around 2Ocm than that of non-vinyl mulching. Rice hulls covering of 4Ocm showed the great heat insulation effects with the soil freezing depth of 1.5cm at sunny place and 6.5cm at shaded lot compared to that of 47cm at sunny and 59.5 cm at shaded place bare ground. 4.Among investingated areas, Dunae, Honeg seong gun was the deepest soil freezing, 89cm with $569^{\circ}C$ of accumulated degree-day of temperature below $0^{\circ}C$ at late February. 5.dehydration of Juniperus C. var. Kaizuca, Euonymus japonica, and Chamaecyparis pisifira at winter season was around 5 %, however dehydration of Vinca minor was more than 10 %. A Studies on the Soil Freezing Depth and Change of Moisture contents in evergreen Plants upon subzero Temperature in Kangwon area.(2)

• Applied Microscopy
• /
• v.43 no.1
• /
• pp.9-13
• /
• 2013

The helium ion microscope (HIM) has recently emerged as a novel tool for imaging and analysis. Based on a bright ion source and small probe, the HIM offers advantages over the conventional field emission scanning electron microscope. The key features of the HIM include (1) high resolution (ca. 0.25 nm), (2) great surface sensitivity, (3) great contrast, (4) large depth-of-field, (5) efficient charge control, (6) reduced specimen damage, and (7) nanomachining capability. Due to the charge neutralization by flood electron beam, there is no need for conductive metal coating for the observation of insulating biological specimens by HIM. There is growing evidence that the HIM has substantial potential for high-resolution imaging of uncoated insulating biological specimens at the nanoscale.

• Korean Journal of Radiology
• /
• v.22 no.11
• /
• pp.1894-1908
• /
• 2021

Double outlet right ventricle (DORV) is a relatively common congenital heart disease in which both great arteries are connected completely or predominantly to the morphologic RV. Unlike other congenital heart diseases, DORV demonstrates various anatomic and hemodynamic subtypes, mimicking ventricular septal defect, tetralogy of Fallot, transposition of the great arteries, and functional single ventricle. Because different surgical strategies are applied to different subtypes of DORV with ventricular septal defects, a detailed assessment of intracardiac anatomy should be performed preoperatively. Due to high spatial and contrast resolutions, cardiac CT can provide an accurate characterization of various intracardiac morphologic features of DORV. In this pictorial essay, major anatomic factors affecting surgical decision-making in DORV with ventricular septal defects were comprehensively reviewed using three-dimensional cardiac CT data. In addition, the surgical procedures available for these patients and major postoperative complications are described.

• Journal of Korea Water Resources Association
• /
• v.30 no.6
• /
• pp.721-729
• /
• 1997

Total scour depth at a bridge is comprised of three components: long-term changes, contraction scour and local scour. Therefore, the analysis of long-term bed elevation changes is very important in the estimation of total scour depth at bridge sites. In this research, long-term bed elevation changes at the Namhan River Bridge are analysed using CHARIMA and HEC-6 models. The results show that, for 5-year steady normal stream flow, the bed elevation is aggreded by 45cm for CHARIMA model but degraded by 5cm for HEC-6 model. For 5-year unsteady flow, the bed elevation is changed greatly and it has a great influence on the estimation of total scour depth. Therefore, to make a proper estimation of total scour depth, not only contraction scour and local scour, but also long-term bed elevation changes should be estimated precisely.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.74-81
• /
• 2013

The high-speed machining in the manufacturing industry field has been widely applied for parts of vehicles, aircraft, ships, electronics, etc., recently, because the effect of cost savings for shortening processing time and improving productivity is great. The purpose in this study is to investigate the effect of cutting depth on the surface roughness of workpiece with the spindle rotational speed and feed rate of high-speed machines as a parameter to find the optimal depth in the finishing for ball end mill of the aluminum alloy 7075 which is used much in aircraft parts. When the cutting depth for the respective feed rate and spindle rotational speed is varied from 0.1 mm to 0.7 mm at intervals of 0.2 mm in the wet finishing of the aluminum alloy 7075 by the insoluble cutting oils and high-speed machining used in the rough machining of previous study, the surface roughness values and the cutting temperature are measured. In addition, the cutting surface shapes of test specimens are observed by optical microscope and compared with respectively. It is found that the surface roughness values and the temperature generated during machining are increased as the feed rate and cutting depth are raised, but those are decreased as the spindle rotational speed is increased.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.15 no.1
• /
• pp.23-32
• /
• 2009

Among welfare facilities for the elderly, necessity for the elderly welfare with diverse advantages is rising in the Small-scale Elderly Care Facilities. The government is expecting great demand in the future. However, current the Facilities lack construction plans that consider characteristics of the elderly. Accordingly, 14 case facilities located in JeollaNamdo and Gwangju were selected to comprehensively analyze the circulation of seniors at care facilities by computing spatial depth and visible area variables. As a result of this study, average spatial depth of bathroom, resting room, physical therapy room and dining hall that seniors frequently get in contact with was found to be deep, but visible area appropriate for the function of space was not available. It showed that the circulation for the elderly was deep spatially and long physically, and the spatial rank along circulation which is perceived visually by the admitted the elderly was clear, thus, providing them abundant visual experience supported by high openness as they move from private space to public space. The obtained visibility, however, was observed not to be matched with the function of each space. Since the Small-scale Elderly Care Facilities require various spaces within small surface area, actual functions of each space must be taken into consideration with hierarchical space organization to obtain an environment that stimulates senses such as vision and hearing. In addition, since the circulation of seniors using facilities must consider aging characteristics and delicate care on spatial depth and physical distances, in-depth studies on planning of the circulation in care facilities are deemed necessary.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.1
• /
• pp.19-23
• /
• 2003

Polished surface of $CsB_{3}O_{5}$ (CBO) has been observed by reflection high energy electron diffraction (RHEED) and X-ray photoelectron spectroscopy (XPS). For comparison, electronic properties of CBO powder have been studied by XPS. It has been found that the crystal surface is covered by thick amorphous layer with chemical composition closely related to that of CBO. Great enrichment of top surface by cesium, ~30 % in reference to the bulk of the modified layer, has been displayed by depth profiling.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.3
• /
• pp.87-93
• /
• 2011

CNC lathe machining has been widely used for parts machining of vehicles, aircraft, ships, electronics, etc. because cost savings for shortening processing time and increasing productivity are great. In this study, the purpose is to investigate the effect of cooling methods such as oil mist, water-soluble cutting oils on the workpiece surface roughness with the cutting speed, cutting depth, tool nose radius and feed rate of CNC lathe machine as a parameter in the cutting process of the aluminum alloy 2024 which is used a lot recently on aircraft parts. It is found that oil mist is coolant and water-soluble cooled by cutting the experimental conditions, cutting speed and cutting depth without effecting the surface roughness value was constant.

• Ocean and Polar Research
• /
• v.25 no.4
• /
• pp.437-446
• /
• 2003

Field measurements of directional waves were carried out during the summer of 2002 at two coastal sites in water of finite depth. A couple of general purpose instruments were used employing acoustic Doppler technology. The aim of the study was to investigate the spatial behavior of the directional movement of waves as they come ashore. In total,74 tests were carried out during which sea states of low to moderate intensity were recorded. A great number of these runs displayed bimodal characteristics of the spreading function at high frequencies. It was found that in general, the frequency-integrated directional width tends to broaden as the water shoals and when refraction effects are negligible. This is attributed to wave-wave interactions that become pronounced in shallow water. The same directional width showed, also, a tendency to increase with increasing peak frequency of the sea state spectrum. The behavior of the kurtosis of the spreading function was also examined. It was found that for higher frequencies this index tends to increase in wave spectra above a certain sea severity threshold.