• Composites Research
• /
• 제15권5호
• /
• pp.14-18
• /
• 2002

본 논문에서는 정수압 환경에서 파괴인성 측정을 위한 일인자방법의 적용성을 검토하기 위해 단일방향 및 준등방성으로 적층된 $\textrm{[}0^{\circ}\textrm{]}_{88}$$\textrm{[}0^{\circ}/\pm/45^{\circ}/90^{\circ}\textrm{]}_{11s}$의 탄소섬유/에폭시 적층복합재에 있어 네 단계 정수압에 대해 탄성일인자를 층간 분리 길이의 함수로 결정 정수압 및 적층각이 탄성일인자에 미치는 영향을 검토하였다. $\textrm{[}0^{\circ}\textrm{]}_{88}$ 경우에는 0.1 MPa, 70MPa, 140MPa, 200MPa의 정수압력을 적용하였으며 $\textrm{[}0^{\circ}/\pm/45^{\circ}/90^{\circ}\textrm{]}_{11s}$에서는 0.1MPa, 100MPa, 200MPa, 300MPa의 정수압력을 적용하였다. 결과로서 탄성일인자는 정수압 및 두 경우 적층각에 의해 영향을 받지 않음을 알 수 있었다. 또한 탄성일인자는 층간분리가 증가함에 따라 선형적으로 감소함을 알 수 있었다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.235-239
• /
• 2005

In this research, we investigated the frequency characteristic of low-velocity impact induced damage signals on graphite/epoxy composite laminates using high-speed fiber Bragg grating(FBG) sensor system. Appling the FBG sensors to damage assessment, we need to study the response of FBG sensors as the damage signals of the different incident angles because FBG shows different directional sensitivity. In order to discriminate an impact induced damage signal from that of undamaged case, drop impacts with different energies were applied to the composite panel with different incident angle to the FBG sensor. Finally, detected impact signals were compared using frequency distributions of wavelet detail components in order to find distinctive signal characteristics of composites delamination.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.107-110
• /
• 2004

In this paper, a new structural health monitoring technique for composite laminates through the use of embedded fiber Bragg grating (FBG) sensors is presented. The method traces the ply stress states of a laminate and compares them with failure criteria during the service time of structures. The ply stress state of every ply composing the composite laminate can be obtained using classical lamination theory by embedded FBG sensors in the laminate. Graphite/epoxy laminate specimens, embedded with three FBG sensors, were fabricated. Tension tests were performed to evaluate the ply stress states tracing technique. Experimental results show that laminates experience fracture when the ply stress states are over the boundaries of failure criteria. In this method, critical damage can be detected by the ply stress states which are close to the boundaries of the failure criteria.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(III)
• /
• pp.333-338
• /
• 2003

Polymeric composite structures used in ground transportation applications such as the carbody of tilting train may be exposed to a ground environmental conditions during long-term missions. In this study, the degradation of mechanical and physical properties of graphite/epoxy composite and glass fabric/phenol composite under ground environmental conditions was investigated. Accelerated environmental conditions of ultraviolet radiation, temperature, and moisture were considered. Several types of specimens were used to investigate the effects of environmental conditions on mechanical properties of the composites. Also, storage shear modulus, loss shear modulus, and tan 8 were measured as a function of exposure times through a dynamic mechanical analyzer. Finally, composite surfaces exposed to environmental conditions were examined using a scanning electron microscope.

• 한국추진공학회지
• /
• 제4권2호
• /
• pp.31-38
• /
• 2000

복합재로 만들어진 압력용기에 대해 작업 중 발생하는 손상의 크기나 상태를 파악하는 것이 본 연구의 관심이다. 충격자는 직경이 25.4mm와 12.7mm인 반구형 2종류와 모서리의 직경이 15mm인 원추형 1종류로 각각 무게가 다르며 떨어뜨리는 자유낙하 높이는 120mm에서 700mm로 종류에 따라 간격을 달리했다. 실험 장치로는 Dynatup 8250을 사용했으며 충격에너지, 최대충격력, 충격변위, contact radius를 측정하고 시험 후 시편은 방사선 촬영을 하여 충격자의 종류에 따라 손상의 정도가 어떻게 다른지를 파악했다. 직경이 25.4mmm인 반구형의 충격자는 직경이 12.7mm인 반구형의 충격자에 비하여 표면의 손상은 적었으나 내부에 delamination크기가 컸다. Contact radius와 최대충격력과의 관계는 실험치와 이론치가 잘 일치했으나 충격에너지와 최대충격력과의 관계는 실험치와 이론치의 차이가 있었다.

• 대한기계학회논문집A
• /
• 제26권7호
• /
• pp.1416-1425
• /
• 2002

In this study, the effects of combined environmental factors on mechanical and thermal analysis properties of graphite/epoxy composites were evaluated by the use of an accelerated aging test. Environmental factors such as temperature, moisture. and ultraviolet were considered. A xenon-arc lamp was utilized for ultraviolet light. and exposure times of up to 3000 hours were applied. Several types of specimens - tensile. bending, and shear specimens those are transverse to the fiber direction, and bending specimens those are parallel to the tiber direction - were used to investigate the effects of environmental factors on mechanical properties of the composites. Also, glass transition temperature, storage shear modulus, loss shear modulus, and tan ${\delta}$ were measured as a function of exposure times through a dynamic mechanical analyzer. In addition. a suitable testing method for determining the effect of environmental factors on mechanical properties is suggested by comparing the results from using two different types of strain measuring sensors. Finally, composite surfaces exposed to environmental factors were examined using a scanning electron microscope.

• 대한기계학회논문집
• /
• 제8권5호
• /
• pp.425-434
• /
• 1984

본 연구에서는 ［0˚/90˚］$_{2s}$, Gr/Gp 복합 적층판에 대해서 접착면의 비율과 폴리에스테르 필름의 구멍의 형상이 적층판의 인장 성질과 파괴인성에 미치는 영향에 대한 실험적인 결과를 얻고자 한다.다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 춘계학술발표대회 논문집
• /
• pp.184-189
• /
• 2000

Two types of fiber-optic sensors, EFPI(extrinsic Fabry-Perot interferometer) and FBG(fiber Bragg grating), have been investigated for measurement of thermal strain and temperature. The EFPI sensor is only for measurement of thermal strain and the FBG sensor is for simultaneous measurement of thermal strain and temperature. FBG temperature sensor was developed to measure strain-independent temperature. This sensor configuration consists of a single-fiber Bragg grating and capillary tube which makes it isolated from external strain. This sensor can then be used to compensate for the temperature cross sensitivity of a FBG strain sensor. These sensors are demonstrated by embedding them into a graphite/epoxy composite plate and by attaching them on aluminum rod and unsymmetric graphitelepoxy composite plate. All the tests were conducted in a thermal chamber with the temperature range $20-100^{\circ}C$. Results of strain measurements by fiber-optic sensors are compared with that from conventional resistive foil gauge attached on the surface.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1696-1701
• /
• 2003

This paper deals with a vibration control analysis of a rotating composite blade, modeled as a tapered thinwalled beam induced by heat flux. The displayed results reveal that the thermally induced vibration yields a detrimental repercussions upon their dynamic responses. The blade consists of host graphite epoxy laminate with surface and spanwise distributed transversely isotropic (PZT-4) sensors and actuators. The controller is implemented via the negative velocity and displacement feedback control methodology, which prove to overcome the deleterious effect associated with the thermally induced vibration. The structure is modeled as a composite thin-walled beam incorporating a number of nonclassical features such as transverse shear, secondary warping, anisotropy of constituent materials, and rotary inertias.

• Bulletin of the Korean Chemical Society
• /
• 제33권11호
• /
• pp.3589-3592
• /
• 2012

Carbon composite bipolar plates with various carbon black contents were prepared by a compression molding method. The electrical conductivity and electrochemical stability of the bipolar plates have been evaluated. It is found that the electrical conductivity increases with increasing carbon black contents up to 15 wt %. When the carbon black contents are greater than 15 wt %, the electrical conductivity decreases because of a poor compatibility between epoxy resin and carbon black, and a weakening of compaction in the carbon composite bipolar plate. Based on the results, it could be concluded that there are optimum carbon black contents when preparing the carbon composite bipolar plate. Corrosion tests show that the carbon composite bipolar plate with 15 wt % carbon black exhibits better electrochemical stability than a graphite bipolar plate under a highly acidic condition. When the optimized carbon composite bipolar plate is applied to vanadium redox flow cells, the performance of flow cells with the carbon composite bipolar plate is comparable to that of flow cells with the graphite bipolar plate.