• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.635-640
• /
• 2016

Electrical behavior of AlN ceramics sintered with $Y_2O_3$ as a sintering aid has been investigated with respect to additional $TiO_2$ dopant. From the impedance spectroscopy, it was found that the grain and grain boundary conductivities have greatly decreased with addition of $TiO_2$ dopant. The $TiO_2$ dopant also increased the activation energy of the grain conductivity by about 0.37 eV; this increase was attributed to the formation of an associate between Al vacancies and Ti ions at the Al sites. Similarly, the electronic conductivity was reduced by $TiO_2$ addition. However, $TiO_2$ solubility in AlN grains was below the detection limit of typical EDX analysis. Grain boundary was clean, without liquid films, but did show yttrium segregation. The transference number of ions was close to 1, showing that AlN is a predominantly ionic conductor. Based on the observed results, the implications of using AlN applications as insulators have been discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.450-453
• /
• 1999

In this paper, The relationship between device performance and channel length(1.5-50$\mu$m) in polysilicon thin-film transistors fabricated by SPC technology was Investigated by measuring electric Properties such as 1-V characteristics, field effect mobility, threshold voltage, subthreshold swing, and trap density in grain boundary with channel length. The drain current at ON-state increases with decreasing channel length due to increase of the drain field, while OFF-state current (leakage current) is independent of channel length. The field effect mobility decrease with channel length due to decreasing carrier life time by the avalanche injection of the carrier at high drain field. The threshold voltage and subthreshold swing decrease with channel length, and then increase in 1.5 $\mu$m increase of increase of trap density in grain boundary by impact ionization.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.7
• /
• pp.1262-1269
• /
• 2002

It is inevitable to evaluate the life of turbine rotor because the operating periods of power plants need to be extended. For the test, seven kinds of specimens with different degradation levels were prepared by the isothermal heat treatment at $630^{\circ}C$. Magnetic methods utilizing Barkhausen noise coercive force($BN_c$) were applied to detect the degradation caused by thermal aging. Magnetic property of material is related with domain dynamics and that is affected by the microstructure of material. Therefore $BN_c$ is very sensitive to the microstructure change of the material. With the increase of degradation, $BN_c$ was decreased and this phenomenon is considered due to precipitations and grain size. The result was compared with Vickers hardness($H_v$) and coercive force($H_c$) to detect the relative variation, and was related with $H_v$ and YS to estimate the change of the mechanical properties with the degradation.

• Current Photovoltaic Research
• /
• v.8 no.1
• /
• pp.27-32
• /
• 2020

CuS thin films were deposited on glass substrates at room temperature by RF magnetron sputtering. The structural and optical properties of CuS thin films grown by varying RF-power from 40 W to 100 W were studied. From the XRD analysis, we confirmed hexagonal crystal structures grown in the preferred orientation of the (110) plane in all CuS thin films, and the intensity of the main diffraction peak increased in proportion to the increase of RF-power. In the case of CuS thin film deposited at 40W, small-sized particles formed a thin and dense surface morphology with narrow pore spacing, relatively. As the power increased, the grain size and grain boundary spacing increased sequentially. The peaks for the binding energy of Cu 2p_3/2 and Cu 2p_1/2 were determined at 932.1 eV and 952.0 eV, respectively. The difference in binding energy for the Cu²⁺ states was the same at 19.9 eV regardless of process parameters. The transmittance and band gap energy in the visible region tended to decrease with increasing sputtering powers.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.5
• /
• pp.505-512
• /
• 2023

This study investigated crystal structures, microstructures, and electric-field-induced strain (EFIS) properties of Bi-based lead-free ferroelectric/relaxor composites. Bi_1/2Na_0.82K_0.18)_1/2TiO₃ (BNKT) as a ferroelectric material and 0.78Bi_1/2(Na_0.78K_0.22)_1/2TiO₃-0.02LaFeO₃ (BNKT2LF) as a relaxor material were synthesized using a conventional solid-state reaction method, and the resulting BNKT2LF powders were subjected to high-energy ball milling (HEBM) after calcination. As a result, HEBM proved a larger average grain size of sintered samples compared to conventional ball milling (CBM). In addition, the increased sintering time led to grain growth. Furthermore, HEBM treatment and sintering time demonstrated a significant effect on EFIS of BNKT/BNKT2LF composites. At 6 kV/mm, 0.35% of the maximum strain (S_max) was observed in the HEBM sample sintered for 12 h. The unipolar strain curves of CBM samples were almost linear, indicating almost no phase transitions, while HEBM samples displayed phase transitions at 5~6 kV/mm for all sintering time levels, showing the highest S_max/E_max value of 700 pm/V. These results indicated that HEBM treatment with a long sintering time might significantly enhance the electromechanical strain properties of BNT-based ceramics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.61-61
• /
• 2009

P-type SGS-TFTs with 10 ${\mu}m$ channel length and two channel widths; $W_1=5{\mu}m$ and $W_2=10{\mu}m$ which has gate insulator made of 20nm $SiO_2$ and 80nm SiNx was fabricated and the electrical properties of them were measured. The field-effect mobility was increased from 95.84 to 104.19 $cm^2/V-s$ and threshold voltage also increased from -0.802 V to -0.954 V, when channel width is increased from5 ${\mu}m$ to 10 ${\mu}m$. Subthreshold swing decreased from 0.418 to 0.343 V/dec and $I_{on/off}$ ratio increased from $4.77{\times}10^7$ to $7.30{\times}10^7$.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.3
• /
• pp.96-100
• /
• 2008

The microstructure, voltage-current, and capacitance-voltage relations ofP CCYA doped ZnO-based varistors were investigated for different amounts of $Al_2O_3$. As the $Al_2O_3$ amount increased, the average grain size (d) increased from d=4.3 to $d=5.5{\mu}m$ and the sintered density $({\rho})$ increased from ${\rho}=5.63$ to ${\rho}=5.67g/cm^3$. As the $Al_2O_3$ amount increased, the breakdown voltage $(V_B)$ increased from $V_B=633$ to $V_B=71$ V/mm and the non-ohmic coefficient $({\alpha})$ increased from ${\alpha}=47$ to ${\alpha}=4$. $Al_2O_3$ served as a donor due to the donor density $(N_d)$, which increases in the range of $N_d=0.77-1.85{\times}10^{18}/cm^3$ with increasing amount of $Al_2O_3$.

• Journal of Hydrogen and New Energy
• /
• v.22 no.4
• /
• pp.458-464
• /
• 2011

Recently, one of the hydrogen production methods has attracted using dense metallic membrane. It has high hydrogen permeation and selectivity which hardly could adopt industrial product because of high cost, hydrogen embrittlment and thermal stability. Meanwhile, vanadium has high hydrogen solubility and it use to instead of Pd-Ag amorphous membrane. Aluminum carried out blocking hydrogen diffusion on grain boundary therefore protecting hydrogen embrittlement. Most of dense metallic membrane is solution diffusion mechanism. The solution diffusion mechanism was very similar hydrogen storing steps such as steps of metal hydride. Thus, V-Al composites were fabricated to use hydrogen induced mechanical alloying. The fabricated V-Al composites were characterized by XRD, SEM, EDS and simultaneous TG/DSC analyses. The hydrogenation behaviors were evaluated using a Sievert's type automatic PCT apparatus. The hydrogenation behaviors of V-Al composites was evaluated too low hydrogen stored capacity and fast hydrogenation kinetics. In PCI results, V-Al composites had low hydrogen solubility, in spite of that, hydrogen kinetics was calculated very fast and hydrogen absorption/desorption contents were same capacity.

• Journal of the Korean Society for Heat Treatment
• /
• v.30 no.2
• /
• pp.43-52
• /
• 2017

Heat treatment condition for dissolution of the M23C6 carbides in 2.25Cr-1Mo-V-Ti material for thermal power plant tube was investigated using a dilatometer method. 2.25Cr-1Mo-V-Ti material was heat-treated at $900{\sim}1,100^{\circ}C$ for 0, 10, 30 min to find the proper dissolution condition of M23C6 carbides. The phase identification and volume fraction of the carbide were measured by using OM, SEM, EBSD and TEM analysis. Optimal heat treatment condition of M23C6 carbide dissolution was selected by predicting dissolution temperature of carbide using Bs points appeared at dilatometer curve. Experimental results showed that the conditions of carbide dissolution was 900, 1,000, $1,100^{\circ}C$ for 30 min. Eventually, the optimal heat treatment condition for dissolution was 30 min at $1,000^{\circ}C$ considering the minimum coarsening of Austenite grain size.

• Journal of Magnetics
• /
• v.15 no.1
• /
• pp.25-28
• /
• 2010

This study examined the crystallographic and magnetic properties of vanadium-substituted lithium cobalt titanium ferrite, $Li_{0.7}Co_{0.2}Ti_{0.2}V_{0.2}Fe_{1.7}O_4$. Ferrite was synthesized using a conventional ceramic method. The samples annealed below $1040^{\circ}C$ showed X-ray diffraction peaks for spinel and other phases. However, the sample annealed above $1040^{\circ}C$ showed a single spinel phase. The lattice constant of the sample was $8.351\;{\AA}$, which was relatively unaffected by vanadium-substitution. The average grain size after vanadium-substitution was $13.90\;{\mu}m$, as determined by scanning electron microscopy. The M$\ddot{o}$ssbauer spectrum could be fitted to two Zeeman sextets, which is the typical spinel ferrite spectra of $Fe^{3+}$ with A and B sites, and one doublet. From the absorption area ratio of the M$\ddot{o}$ssbauer spectrum, the cation distribution was found to be ($Co_{0.2}V_{0.2}Fe_{0.6})[Li_{0.7}Ti_{0.2}Fe_{1.1}]O_4$. Vibrating sample magnetometry revealed a saturation magnetization and coercivity of 36.9 emu/g and 88.6 Oe, respectively, which were decreased by vanadium-substitution.