• 한국재료학회지
• /
• 제25권10호
• /
• pp.559-565
• /
• 2015

The ductile-brittle transition behavior of two austenitic Fe-18Cr-10Mn-N-C alloys with different grain sizes was investigated in this study. The alloys exhibited a ductile-brittle transition behavior because of an unusual brittle fracture at low temperatures unlike conventional austenitic alloys. The alloy specimens with a smaller grain size had a higher yield and tensile strengths than those with a larger grain size due to grain refinement strengthening. However, a decrease in the grain size deteriorated the low-temperature toughness by increasing the ductile-brittle transition temperature because nitrogen or carbon could enhance the effectiveness of the grain boundaries to overcome the thermal energy. It could be explained by the temperature dependence of the yield stress based on low-temperature tensile tests. In order to improve both the strength and toughness of austenitic Fe-Cr-Mn-N-C alloys with different chemical compositions and grain sizes, more systematic studies are required to understand the effect of the grain size on the mechanical properties in relation to the temperature sensitivity of yield and fracture stresses.

• 대한기계학회논문집
• /
• 제11권6호
• /
• pp.867-876
• /
• 1987

본 연구에서는 보통강재인 SS 41 강을 열처리하여 얻은 M.E.F.복합조직강의 모상입경변화와 3.5% NaCl수용액의 pH변화 조건하에서 반복굽힘피로실험을 하여 부식 피로파괴에 미치는 영향에 대해 고찰하였다.

• 대한지리학회지
• /
• 제48권6호
• /
• pp.819-836
• /
• 2013

본 연구는 백령도 사곶 사빈에서 채취한 사질 시료를 대상으로 레이저 회절 입도분석기를 이용한 입도분석에 있어서 전처리 및 굴절율과 흡수율의 영향을 비교하고, 사질 시료의 적절한 입도분석 절차 및 방법을 제시하고자 한다. 본 연구에 적용된 세 가지 전처리 방법에 따라 입도분석 결과는 서로 큰 차이를 보이지 않지만, 과산화수소 처리를 했을 경우, 그렇지 않았을 때와 차이를 보이고 있어, 과산화수소 처리를 통해 유기물은 제거되어야 한다. 시료의 입도분석 결과는 굴절율 1.3과 흡수율 0.01 이하에서 다른 지수가 적용되었을 때와 차이를 보이고 있다. 이러한 차이는 세립질 시료에 비하면 그리 크지 않으며 따라서 굴절율과 흡수율도 사질 시료의 입도분석 결과에 큰 영향을 미치지 않는다. 그러나 굴절율 1.3과 흡수율 0.01 이하 이외의 다른 지수를 적용할 필요가 있다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 센서 박막재료
• /
• pp.47-51
• /
• 2001

The structural properties of varistors surface studied by fractal phenomenon were investigated to verify the relations of electrical characteristics. The SEM photograph of varistors surface were changed by binary code and the grain shape of that were analyzed by fractal dimension. The void of varistors surface was found by fractal program. The relation between grain density and electrical properties depend on fractal dimension. The grain size in varistors surface was decreased by increasing of oxide antimony addition. The grain size of devices by oxide antimony addition were from 5 to $10[{\mu}m]$. The fractal dimension and electrical properties of varistors surface was related to between grain boundary and grain density. The grain size was decreased by increasing of fractal dimensions.

• 산업기술연구
• /
• 제20권B호
• /
• pp.3-8
• /
• 2000

Low cycle fatigue life of spheroidal graphite cast iron is determined by the morphological parameters of internal graphite. The aim of this study is to clarify the effect of the number of nodular grain of spheroidal graphite cast iron on low cycle fatigue life. Two specimens that have identical average nodular grain size by changing nodular grain volume fraction and different number of nodular grain count was tested. In this paper, the parameter governing fatigue life through fatigue test, the number of nodular grain seriously affect fatigue life and nodular grain size is no longer governing parameter of it.

• Nuclear Engineering and Technology
• /
• 제34권2호
• /
• pp.132-141
• /
• 2002

The effects of microstructure on fretting wear were investigated in Inconel 690 tube. The microstructure observation indicated that the solution annealing temperature and time affected the grain size of the Inconel 690 tubes. The carbide morphology, along grain boundaries, was mainly affected by thermal treatment time and temperature. The wear test results showed that specimens with larger grain size and with coarse carbides along grain boundaries had better wear resistance. Cracks were found in specimens with carbides along the grain boundary, while few cracks were found in carbide free specimens. It seemed that the carbides on grain boundary assisted crack formation and propagation in carbide containing specimens. On the other hand, the micro-hardness of specimen did not have a major role in fretting wear. It could be inferred from the SEM images of worn surfaces that the main wear mechanism of carbide containing specimen was delamination, while that of carbide free specimen was abrasion.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 1998년도 추계학술대회 및 발표대회 강연 및 발표논문 초록집
• /
• pp.10-10
• /
• 1998

The growth process of solid grains in a liquid matrix is usually explained in tem1S of Ostwald ripening. The variation of growth (dissolution) rate as a function of grain size during Ostwald ripening predicted that the dissolution rate becomes very large as grain size decreases but the growth rate of a large grain is rather limited. Therefore. a rather uniform size distribution of grain size is maintained once after the quasi-equilibrium state is reached. Quite frequently, however, the exaggerated grain growth (EGG) is observed to occur: only a limited number of grains grow exceptionally. From the observation that the EGG occurs only for the faceted grains with apparently straight solid-liquid interfaces, the EGG is suggested to be the consequence of growth process controlled by 2-dimensional nucleation. In this study, the result by computer calculation on the grain growth process controlled by various mechanisms will be given.

• 한국세라믹학회지
• /
• 제32권6호
• /
• pp.653-658
• /
• 1995

Directional effect of applied pressure during sintering on the microstructure and fracture toughness of the heat-treated silicon nitride ceramics has been investigated. The specimens with a composition of 92Si3N4-8Y2O3(in wt%) were sintered at 172$0^{\circ}C$ by a hot press (HP ) and a hot isostatic press (HIP) and heat-treated for grain growth at 1800~20$0^{\circ}C$. The fracture toughness of the HP samples increased with the grain size while the fracture toughness of the HIP treated samples remained the same even though the grain growth occurred. This discrepancy was explained by a bimodal grain size distribution and large aspect ratio of the HPed samples and a monomodal grain size distributjion and samll aspect ratio of the HIP treated samples.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.40-47
• /
• 1995

Electrical properties of ZnO ceramics based on Bi oxide was investigated in relation to sintering temperature. In the temperature range >$1150^{\circ}C$ to >$1350^{\circ}C$ the grain size increased from 9.mu.m to 20.mu.m when the sintering temperature was raised. The leakage current in the low voltage range increased as the potential barrier decreases, which is caused by increasing the grain size at high temperature. The dielectric characteristics of the ZnO ceramics was also affected by sintering temperature. Large dielectric constant was attributed, to the grainboundary layer of polycrystalline ZnO ceramics and decreasing grainboundary width. The variation of breakdown voltage with sintering temperature was attributed to the change of the donor concentration in the ZnO grain and grain size. The results showed that breakdown voltage increased decreasing grain size and donor concentration. Nonohmic coefficient was associated with the lower breakdown voltage per grainboundary layer due to the grain growth and higher donor concentration.

• 열처리공학회지
• /
• 제9권3호
• /
• pp.198-204
• /
• 1996

This work was carried out in order to investigate the effect of grain size on martensitic transformation temperature and morphology of Fe-27%Ni-0.27%C alloy. The martensitic transformation temperature was raised with increasing the austenitizing temperature within the range from $750^{\circ}C$ to $1200^{\circ}C$, owing to the grain growth, vacancy concentration. It was observed that the larger was the austenite grain, the higher was the martensitic transformation temperature. The influence of the austenite grain size was similar to that of the austenitizing temperature. The morphology of martensite in Fe-27%Ni-0.27%C alloy changed from lath to lenticular with the variation of grain size. From the above results, it was concluded that the martensitic transformation temperature and morphology was mainly dependent upon the austenite grain size.