• 한국해양학회지:바다
• /
• 제16권4호
• /
• pp.169-179
• /
• 2011

본 연구에서는 미량 금속의 농축 가능성이 제기되는 천수만 퇴적물에 대하여 미량 금속의 조절 요인과 농축 정도를 파악하고자 하였다. 천수만 전역에 걸쳐 27개의 표층 퇴적물을 채취하였으며, 입도, 비표면적, 유기탄소 및 탄산칼슘 함량과 주성분 및 미량 금속(Al, Fe, Na, K, Mg, Ca, Ti, Mn, P, S, Ba, Sr, Li, Co, Cr, Ni, Cu, Zn, As, Cd, Cs, Sc, V, Sn) 농도를 분석하였다. 퇴적물의 총 금속 농도는 크게 3 가지 요인(석영, 희석, 탄산칼슘, 굵은 모래 혹은 정장석)에 의해 조절되었는데 V, Co, Cr, Ni, Cu, Zn, As, Cd는 석영 희석 효과(quartz dilution effect)에 의해 Mn 및 As는 석영 희석 효과와 정장석(굵은 모래) 함량의 복합적 요인에 의해 조절되었다. 농축 인자(enrichment factor) 및 약산(1 M HCl) 용출 실험 결과 천수만 퇴적물에서 미량 금속은 농축되지 않았음을 알 수 있었으며 금속의 농도는 퇴적물의 지화학적 특성들로 잘 설명되었다. 특징적으로 As는 조립질 퇴적물에서도 세립질 퇴적물과 유사한 농도를 보여주었는데, 이것은 조립질 퇴적물 내 Mn 산화물(용출 부분) 및 정장석(잔류 부분)과 밀접한 관련이 있는 것으로 해석되었다. 따라서 퇴적물 중 As의 농축 정도를 평가할 경우, 모래질을 포함하는 시료는 모래질 부분을 따로 분리하거나 $16{\mu}m$보다 작은 세립질 퇴적물의 함량이 10% 이상인 시료만을 대상으로 하는 것이 합리적인 것으로 판단된다.

• 한국전기전자재료학회논문지
• /
• 제25권11호
• /
• pp.878-885
• /
• 2012

In this study we aims to examine the co-doping effects of 1/3 mol% $Mn_3O_4+Co_3O_4$ (1:1) on the reaction, microstructure, and electrical properties such as the bulk defects and grain boundary properties of $ZnO-Bi_2O_3-Sb_2O_3$ (ZBS; Sb/Bi=0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Mn,Co-doped ZBS, ZBS(MCo) varistors were controlled by Sb/Bi ratio. Pyrochlore ($Zn_2Bi_3Sb_3O_{14}$) was decomposed and promoted densification at lower temperature on heating in Sb/Bi=1.0 by Mn rather than Co. Pyrochlore on cooling was reproduced in all systems however, spinel (${\alpha}$- or ${\beta}$-polymorph) did not formed in Sb/Bi=0.5. More homogeneous microstructure was obtained in $Sb/Bi{\geq}1.0$ In ZBS(MCo), the varistor characteristics were improved drastically (non-linear coefficient, ${\alpha}$=30~49), and seemed to form $Zn_i^{..}$(0.17 eV) and $V_o^{\bullet}$(0.33 eV) as dominant defects. From impedance and modulus spectroscopy (IS & MS), the grain boundaries have divided into two types, i.e. the one is tentatively assign to $ZnO/Bi_2O_3(Mn,Co)/ZnO$ (0.47 eV) and the other ZnO/ZnO (0.80~0.89 eV) homojunctions.

• Journal of Welding and Joining
• /
• 제18권2호
• /
• pp.176-176
• /
• 2000

Recently developed Austenite stainless steel,309L was to overlay on 3Cr-1Mo-V-Ti-B steels, using Electroslag welding process, which wide electrodes were adopted. Transition region in welding interlayer relating to disbonding crack was investigated. Also. the effect of welding condition on the width of transition region and coarsening grains of the austenite were studied.1) With increasing welding speed the width of martensite at transient region was increased, but the amount of delta ferrite in weld metal was reduced, being fine grained.2) The form of martensite at the transition region was occured by reversible transition region, leading to increasing Ms point.3) With increasing welding speed, the grain of austenite formed at the welding interface was finer. With increasing welding current under the same welding speed, the grain size of the austenite was finer. At high current, original grain size of the austenite is coarse, but the austenite has fine grains because the austenite was transformed to martensite during cooling.4) In the case of high welding speed, the width of martensite at the welding interface was increased, but the grain size of austenite at the welding interface was finer. This indicates that the inhibition of disbonding crack may be achieved through dispersening fine carbides in the grain boudary.(Received August 3, 1999)

• 소성∙가공
• /
• 제27권6호
• /
• pp.347-355
• /
• 2018

This study investigated the effects of the processing number of multi-axial diagonal forging (MADF) on the microstructural changes of OFC fabricated by MADF processes. The as-extruded OFC was cut to $25mm^3$ cube for the MADF processes. The MADF process consists of plane forging with a thickness reduction of 30% and diagonal forging with a diagonal forging angle of $135^{\circ}$. In order to analyze the microstructural evolutions according to the number of repetitions, 1, 2, 3 and 4 cycles of the MADF process were performed. OFC specimens were successfully deformed without surface cracking for up to 4 cycles of MADF. The grain size, average misorientation and average grain orientation spread (GOS) of MADF processed materials were analyzed using EBSD technique and their Vicker's hardness were also measured. The results showed that MADF process effectively refined the microstructure of OFC with initial average grain size of $84.2{\mu}m$. The average grain sizes of specimens MADF processed for 1, 2, 3, 4 cycles were refined to be $8.5{\mu}m$, $2.2{\mu}m$, $1.5{\mu}m$, $1.1{\mu}m$, respectively. The grain refinement seemed to be saturated when OFC was MADF processed over 2 cycles. In the case of specimens subjected to two or more cycles of MADF, the degree of decrease in average grain size was drastically reduced as the number of cycles increased due to softening phenomena such as dynamic recovery or dynamic recrystallization during processing. The degree of increase in average Vicker's hardness was also dramatically reduced as the number of cycles increased due to the same reason.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.262.1-262.1
• /
• 2013

ZnO 나노구조는 전기적 성질과 화학적인 안정성 때문에 가스센서, 투명 전극 및 태양전지와 같은 전자소자와 광소자에 널리 사용되고 있다. ZnO 박막을 증착하는 방법은 Physical Vapor Deposition과 Chemical Vapor Deposition이 있으나 나노 구조를 가진 SnO2를 형성하기 어렵다. 전기 화학적 증착(Electrochemical Deposition: ECD)은 낮은 온도에서 진공 공정이 필요하지 않기 때문에 경제적이며 빠른 성장 속도를 가지고 있기 때문에 ZnO 나노 구조를 효과적으로 형성 할 수 있다. 본 연구에서는 Indium Tin Oxide (ITO) 기판 위에 ZnO 나노 구조를 형성시켜 전기적 및 구조적 특성을 관찰하였다. 0.1 M zinc nitrate와 0.1 M potassium chloride를 용매에 각각 용해하여 ZnO 나노구조를 성장하였다. ZnO 나노구조를 성장하기 위하여 인가전압을 -0.75 V부터 -2.5 V까지 0.5 V 간격으로 변화하였다. X-선 회절 분석결과에서 ZnO의 피크의 크기가 큰 전기화적적 성장 전압구간과, 주사전자현미경 분석결과에서 나노 구조가 가장 잘 나타난 성장 전압구간을 다시 0.1 V 간격으로 세분화하여 최적화 조건을 분석하였다. X-선 회절 실험으로 형성한 ZnO 나노구조의 피크가 (110) (002)로 나타났다. X-선 회절 분석의 intensity의 값이 (002)방향이 가장 크게 나타났으므로 우선적으로 (002) 방향으로 ZnO 나노구조가 성장됨을 알 수 있었다. 주사전자현미경상은 grain size가 200~300 nm 사이의 ZnO 나노구조가 형성되며, grain size가 전기화학적 증착 장치의 성장전압이 커짐에 따라 커지는 것을 알 수 있었다.

• 센서학회지
• /
• 제4권3호
• /
• pp.15-21
• /
• 1995

본 논문은 졸겔법에 의해 $TiO_{2}-V_{2}O_{5}$ 습도센서를 제조하고, 미세구조 및 결정구조를 분석하여 습도감지특성이 뛰어난 최적 제조조건을 찾았다. 그레인 크기는 $Ti^{4+}$ 사이트에 치환되는 $V^{5+}$비에 비례하여 증가하였다. X-선 회절분석 결과, $V_{2}O_{5}$비에 관계없이 $V^{5+}$피크는 확인할 수 없었다. 실험결과로부터 $V_{2}O_{5}$비가 1mol%, 열처리온도가 $700^{\circ}C$일때 가장 우수한 습도감지특성을 나타내었다. 시편의 정전용량은 주파수가 증가할수록 감소하였다.

• 소성∙가공
• /
• 제28권2호
• /
• pp.63-70
• /
• 2019

This study investigates the effects of multi-axial diagonal forging (MADF) processing number on the microstructures of AA1100 fabricated using MADF processes. The cast AA1100 was annealed at $400^{\circ}C$ for 3hrs in $N_2$ atmosphere and cut into $25mm^3$ cubes for the MADF processes. The MADF process consist of plane forging with a thickness reduction of 30% and a diagonal forging with a diagonal forging angle of 135 degrees. In order to analyze the microstructural variations based on the number of repetitions, 1, 2, 3 and 4 cycles of the MADF process were performed. AA1100 specimens were successfully deformed without cracking of the surface for up to 4 cycles of MADF. The grain size, average misorientation and average grain orientation spread (GOS) of MADF processed materials were analyzed using EBSD technique. The results showed that MADF process effectively refined the microstructure of AA1100 with an initial average grain size of $337.4{\mu}m$. The average grain sizes of specimens which were MADF processed for 2, 3, 4 cycles were refined to be $1.9{\mu}m$, $1.6{\mu}m$, $1.4{\mu}m$, respectively. The grain refinement appeared saturated when AA1100 got MADF processed over 2 cycles. When the specimen was subjected to two or more cycles of MADF, the degree of decrease in the average grain size drastically decreased with an increase in the number of cycle due to the softening phenomena such as dynamic recovery or dynamic recrystallization during processing.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.212-212
• /
• 2014

0.04% Gd-duplex stainless steels (Gd-DSTSs) for neutron absorbing materials were inert arc-melted and poured into a Y-shape block with the size of $100{\times}100{\times}20[mm]$. The Gd-DSTS was hot rolled at $1200^{\circ}C$ followed by cold rolling to have 33% reduction. The average grain sizes of the rolling (RD), transverse (TD) and short transverse (ST) directions were 6, 7, $11{\mu}m$, respectively. The micro-hardnesses of the RD, TD and ST directions were 258.5, 292.3, 314.7 $H_V$, respectively. Corrosion potential and corrosion rate of the cold rolled Gd-duplex stainless steel in aerated artificial sea water and 0.1M $H_2SO_4$ solution were $0.2216V_{SHE}$, $0.0106A/cm^2$, $-0.0825V_{SHE}$, $0.0168A/cm^2$ for RD, $0.2210V_{SHE}$, $0.0077A/cm^2$, $0.0817V_{SHE}$, $0.0092A/cm^2$ for TD, $0.1056V_{SHE}$, $0.0059A/cm^2$, $0.0475V_{SHE}$, $0.0069A/cm^2$ for ST, respectively. The corrosion behavior depended on the texture, which were due to mainly grain boundary and minorly crystallographic texture. Friction coefficient and wear resistance were 2.07 and 0.48 mm, respectively.

• Corrosion Science and Technology
• /
• 제2권2호
• /
• pp.82-87
• /
• 2003

Stress corrosion cracking of Alloy 600 and Alloy 690 has been studied with a C-ring specimen in 1%, 10% and 40% NaOH at $315^{\circ}C$. SCC test was performed at 200 mV above corrosion potential. Initial stress on the apex of C-ring specimen was varied from 300 MPa to 565 MPa. Materials were heat treated at various temperatures. SCC resistance of Ni-$_\chi$Cr-10Fe alloy increased as the Cr content of the alloy increased if the density of an intergranular carbide were comparable. SCC resistance of Alloy 600 increased in caustic solution as the product of coverage of an intergranular carbide in grain boundary, intergranular carbide thickness and Cr concentration at grain boundary increased. Low temperature mill annealed Alloy 600 with small grain size and without intergranular carbide was most susceptible to SCC. TT Alloy 690 was most resistant to SCC due to the high value of the product of coverage of an intergranular carbide in grain boundary, intergranular carbide thickness and Cr concentration at grain boundary. Dependency of SCC rate on stress and NaOH concentration was obtained.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.397-397
• /
• 2012

에너지갭이 큰 SnO2 반도체는 빛 투과율이 우수하여 투명성이 좋으며 화학적으로 안정된 구조를 가지고 있어 전자소자 및 광소자 응용에 대단히 유용하다. SnO2 박막을 증착하는 방법은 Physical Vapor Deposition과 Chemical Vapor Deposition이 있으나 나노 구조를 가진 SnO2를 형성하기 어렵다. 전기 화학적 증착 (Electrochemical Deposition: ECD)은 낮은 온도에서 진공 공정이 필요하지 않기 때문에 경제적이며 빠른 성장 속도를 가지고 있기 때문에 SnO2 나노 구조를 효과적으로 형성 할 수 있다. 본 연구에서는 Indium Tin Oxide (ITO) 기판 위에 SnO2 나노 구조를 형성시켜 전기적 및 구조적 특성을 관찰하였다. 0.015 M의 Tin chloride pentahydrate(SnCl4 5H2O)를 타켓 물질로 사용하고 0.1 M의 KCl을 완충물질로 사용하여 SnO2 나노구조를 성장하였다. 타겟 물질이 잘 녹지 않으므로 DI water와 ethanol을 7：3의 비율로 용매 사용하였다. 전류-전압 곡선을 분석하여 최적의 성장조건을 확보하고, $65^{\circ}C$ 1기압 하에서 -2.5 V 부터 -1.0 V까지 0.5 V 간격으로 나누어서 SnO2 나노구조를 성장하였다. X-선 회절 분석결과에서 SnO2의 피크의 크기가 큰 전기화적적 성장 전압구간과, 주사전자현미경 분석 결과에서 나노 구조가 가장 잘 나타난 성장 전압구간을 다시 0.1 V 간격으로 세분화하여 최적화 조건을 분석하였다. X-선 회절 실험으로 형성한 SnO2 나노구조의 피크가 (110) (101) (200) (211) (310)로 나타났다. X-선 회절 분석의 intensity의 값이 (101)방향이 가장 크게 나타났으므로 우선적으로 (101) 방향으로 SnO2 나노구조가 성장됨을 알 수 있었다. 주사전자현미경상은 grain size가 50~100 nm 사이의 SnO2 나노구조가 형성되며, grain size가 전기화학적 증착 장치의 성장전압이 저 전압 구간에서 커지는 것을 알 수 있었다.