• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.396-396
• /
• 2009

Chalcopyrite semiconductor $CuInSe_2$ nanoparticles were prepared using a low temperature colloidal route by reacting the starting materials (CuI, $InI_3$ and $Na_2Se$) in solvents. After synthesised $CuInSe_2$ nanoparticles precursors were mixed with organic binder for the viscosity of the precursor slurry to be suitable for the doctor blade method. The mixture of $CuInSe_2$ and binder was deposited onto molybdenum-coated sodalime glass substrates to form thin film. The precursor thin films were preheated on the hot plate to remove remaining solvents and binder material. After subsequent thermal processing of the thin film under a selenium ambient, $CuInSe_2$ absorber layer with grain size significantly lager than that of the nanoparticles was formed.

• Journal of Korea Foundry Society
• /
• v.15 no.5
• /
• pp.514-522
• /
• 1995

The microstructural evolution with isothermal stirring during semi-solid state processing of hypoeutectic Al-6.2wt%Si alloy was studied. Substructure of the individual primary solid particle in the slurry was investigated through transmission electron microscopy(TEM). Formation of subgrain boundaries on the rheocast Al-6.2wt%Si alloy is observed and the misorientation between the grains is shown typically under 2 degrees by analyzing selected area diffraction (SAD) and convergent beam electron diffraction (CBED) patterns. The existence of high angle grain boundaries are also observed in the alloy. Based upon these observations, mechanisms for the primary particles fragmentation are considered. With isothermal stirring, the dislocation density increases, and the evolution of dislocation cell structure takes place, which is interpreted as a process of achieving uniform deformation by dynamic recovery under applied shear stress.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.622-627
• /
• 2016

The effects of the debinding atmosphere on the properties of sintered reaction-bonded $Si_3N_4$ (SRBSN) ceramics prepared by tape casting method were investigated. Si green tape was produced from Si slurry of Si powder, using 11.5 wt% polyvinyl butyral as the organic binder and 35 wt% dioctyl phthalate as the plasticizer. The debinding process was conducted in air and $N_2$ atmospheres at $400^{\circ}C$ for 4 h. The nitridation process of the debinded Si specimens was performed at $1450^{\circ}C$, followed by sintering at $1850^{\circ}C$ and 20 MPa. The results revealed that the debinding atmosphere had a significant effect on $Si_3N_4$ densification and thermal conductivity. Owing to the higher sintered density and larger grain size, the thermal conductivity of $Si_3N_4$ specimens debinded in air was higher than that of the samples debinded in $N_2$. Thus, debinding in air could be suitable for the manufacture of high-performance SRBSN substrates by tape casting.

• Journal of the Korean Ceramic Society
• /
• v.54 no.3
• /
• pp.200-204
• /
• 2017

Molybdenum (Mo), an electrode material of alkali metal thermal-to-electric converters (AMTEC), facilitates grain growth behavior and forms Mo-Na-O compounds at high operating temperatures, resulting in reduced performance and shortened lifetime of the cell. Mo/TiN composite materials have been developed to provide a solution for such issues. Mo is a metal that possesses excellent electrical properties, and TiN is a ceramic compound with high-temperature durability and catalytic activity. In this study, a dip-coating process with an organic solvent-based slurry was used as an optimal coating method to achieve homogeneity and stability of the electrodes. Cell performance was evaluated under various conditions such as the number of coatings, ranging from 1 to 3 times, and heat treatment temperatures of $800-1100^{\circ}C$. The results confirmed that the cell yielded a maximum power of 9.99 W for the sample coated 3 times and heat-treated at $900^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.189-189
• /
• 2008

Due to the environmental issue vast research is going on to replace the widely used lead contented piezoelectric materials. Bismuth sodium titanate (abbreviated as BNT) based bismuth sodium titanate-barium titanate (abbreviated as BNBT) ceramic was prepared by using modified method rather than conventional mixed oxide method. This modification was made to improve the properties of BNT based ceramic. In this procedure $BaTiO_3$ (abbreviated as BT) was prepared using conventional mixed oxide method. Analytical grade raw materials of $BaCO_3$ and $TiO_2$ were weighted and ball milled using ethanol medium. The mixed slurry was dried and sieved under 80 mesh. Then the powder was calcined at $1100^{\circ}C$ for 2 hours. This calcined BT powder was used in the preparation of BNBT. Stoichiometric amount of $Bi_2O_3$, $Na_2CO_3$, $TiO_2$ and BT were weighted and mixed by using ball mill. The used calcination temperature was $850^{\circ}C$ for 2 hours. Calcined powder was taken for another milling step. BNBT disks were pressed to 15 mm of diameter and then cold isostatical press (CIP) was used. Pressed samples were sintered at $1150^{\circ}C$ for 2 hours. The SEM microstructure analysis revealed that the grain shape of the sintered ceramic was polyhedral and grain boundary was well matched where as the sample prepared by conventional method showed irregular arrangement and grain boundary not well matched. And sintered density was better (5.78 g/cc) for the modified method. It was strongly observed that the properties of BNBT ceramic near MPB composition was found to be improved by the modified method compare to the conventional mixed oxide method. The piezoelectric constant dB of 177.33 pC/N, electromechanical coupling factor $k_p$ of 33.4%, dielectric constant $K_{33}^T$ of 688.237 and mechanical quality factor $Q_m$ of 109.37 was found.

• Journal of the Korean Ceramic Society
• /
• v.43 no.7 s.290
• /
• pp.421-426
• /
• 2006

[ $(BaSr)TiO_3$ ] thick films were prepared by tape casting method, using $BaTiO_3\;and\;SrTiO_3$ powder slurry in order to investigate dielectric properties i.e. dielectric constant, ${\varepsilon}_r$, Curie temperature, $T_c$. Grain growth within $(BaSr)TiO_3$ thick films was observed with increasing weight ratio of $BaTiO_3$. This observation can be explained by phenomena of substitution of $Sr^{2+}$ ion for $Bi^{2+}$ ion in the $BaTiO_3$ system. Also, the Curie temperature in $(BaSr)TiO_3$ thick films was shifted to lower temperature range with increasing $ SrTiO_3$. Furthermore, Curie temperature having maximum dielectric constant was in the range of $-40^{\circ}C\;to\;30^{\circ}C$, and hence sharper phase transformation occurred at Curie temperature. There occurred decrease in tunability and k-factor of $(Ba_{0.6}Sr_{0.4})TiO_3$ calculated from the dielectric constant, ${\varepsilon}_r$ above Curie temperature. In addition, above the $60^{\circ}C$, phase fixation was observed. This means that internal stress relief occurred with increasing $90^{\circ}$ domains.

• Korean Journal of Materials Research
• /
• v.12 no.4
• /
• pp.269-273
• /
• 2002

The NASICON solid electrolyte films, $Na_{1+x}Zr_2Si_xP_{3-x}O_{12}$(1.5< x < 2.3), was prepared from ceramic slurry by modified doctor-blade process. The NASICON solid electrolyte and fabricated sensors, Pt-electrode/NASICON/Carbonate$(Na_2CO_3-K_2CO_3CaCO_3\; system)$ electrode, were investigated to measure phase, microstructure and e.m.f variation for sensing $CO_2$ concentration. The uniform grain size of $2-4{\mu}m$ and major phase of sodium zirconium silicon phosphate phase, $Na_{1+x}Zr_2Si_xP_{3-x}O_{12}$was identified with X-ray diffraction patterns and scanning electron microscopy, respectively. The Nernst's slope of 84 mV/decade for $CO_2$ concentration from 500 to 8000 ppm was obtained at operating temperature of $400^{\circ}C$.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.25 no.4
• /
• pp.251-258
• /
• 2005

This study was conducted to examine the effect of application of pig manure slurry(PMS) for rye cultivation in Paddy-land on rice productivity The field experiments were carried out from 1999 to 2002 on well-grown rice in Paddy-land at Kimje, Chunbuk province in Korea. PMS was manufactured by the fermentation for 6 months in natural condition. Amount of PMS was adjusted equal to total nitrogen value relative to its value of commercial chemical fertilizers. The amount of PMS were spread evenly over the soil surface two times; first in the autumn (before sowing, end of November) and second in the spring(regrowth of rye, middle of March). The field plots were consisted of four kinds (PMS $100\%$ treatment, PMS $200\%$ treatment PMS $100\%$ treatment with half of CF (CF $50\%$), Full of CF treatment (CF $100\%$). The experiment was designed as a randomized complete block. Each treatment was replicated three times. Rices are customarily gown under tropical korean condition as annuals. The results obtained from this study were summarized as fellows. Panicle length of rice was shorter in PMS $100\%$ than other treatments. Ripening grain ratio was the lower in CF treatment. In treatment of PMS $100\%$ and PMS $200\%$, 1000 grain weight was a downward trend as compared to that of full of CF treatments, whereas number of grains per $m^2$ was increased as compared to other treatments. Number of panicles reveals that there is an increase in order; CF $50\% + PMS\;100\%>\;PMS\;100\%\;>\;CF\;100\%\;>\;PMS\;200\%$. Yield of milled rice showed hi인 in CF $100\%$ and $CF 50\%+ PMS 100\%$, but were was no significant difference among treatments. There were did not a regular tendency in the ratio of leaf sheath bright, however the ratio of lodging area was higher in $CF50\%+PMS\;100\%$ treatment than other treatments. Based on the results of this experiment, $CF 50\%+PMS\;100\%$ may be the most effective in rice productivity under application of PMS for rye cultivation in Paddy-land.

• Applied Chemistry for Engineering
• /
• v.20 no.3
• /
• pp.317-321
• /
• 2009

In order to analyze the high temperature phase formation and the sinterability of super ionic conductor $K^+-{\beta}/{\beta}"-Al_2O_3$ which is commonly used as a solid oxide electrolyte, the pure $K^+-{\beta}/{\beta}"-Al_2O_3$ powder in the ternary system $K_2O-LiO_2-Al_2O_3$ was synthesized by solid state reaction and formed to tube and disk using slip casting method and cold isostatic pressing (CIP), respectively. The slip casting was conducted in an alumina mold with the slurry containing 40 wt% of solid contents and the CIP was carried out under 20 MPa. The samples were sintered at $1600^{\circ}C$, $1700^{\circ}C$ and $1750^{\circ}C$, respectively, and their phase formation and the sintering density were investigated according to the forming method. The samples produced by CIP showed far higher ${\beta}"-Al_2O_3$ fraction as compared with those by slip casting. On the other hand, the samples by slip casting showed slightly higher sintering density. The relative density reached to about 83% at $1750^{\circ}C$ and for 1 h, independent of the forming method. In the case of 90 min socking time, the density was decreased owing to the exaggerated grain growth and the pores by $K_2O$ evaporation.

• Tunnel and Underground Space
• /
• v.24 no.6
• /
• pp.449-463
• /
• 2014

There are many case studies and application cases in abandoned mines for hydraulic filling method filled by slurry or paste form, but research on the pneumatic filling is not applied in Korea. The damage of steel pipe is occurred by wear due to the flow of filling material in the bent area of steel pipe in traditional pneumatic filling method. In this study, the new pneumatic filling method was developed using a newly devised improved nozzle to improve the above problem. The model test for mine filling was performed in the laboratory for the simulated accessible or inaccessible mine cavities, and the filling efficiency by the results obtained from the test was calculated. The filling efficiency was analyzed from the variation of outlet angle, feed rate and grain size of sand in model test of simulated accessible mine cavity. The superiority of improved pneumatic filling method was proved through the analysis of filling efficiency by the results obtained from each model tests of gravitational, traditional, and improved filling method in simulated inaccessible mine cavity.