• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.340-341
• /
• 2005

Lithium titanium oxide as anode material for energy storage prepared by novel synthesis method. $Li_4Ti_5O_{12}$ based spinel-framework structures are of great interest material for lithium-ion batteries. We describe here $Li_4Ti_5O_{12}$ a zero-strain insertion material was prepared by novel sol-gel method and by high energy ball milling (HEBM) of precursor to from nanocrystalline phases. According to the X-ray diffraction and scanning electron microscopy analysis, uniformly distributed $Li_4Ti_5O_{12}$ particles with grain sizes of 100nm were synthesized. Lithium cells, consisting of $Li_4Ti_5O_{12}$ anode and lithium cathode showed the 173 mAh/g in the range of 1.0 $\sim$ 3.0 V. Furthermore, the crystalline structure of $Li_4Ti_5O_{12}$ didn't transfer during the lithium intercalation and deintercalation process.

• Journal of Powder Materials
• /
• v.17 no.5
• /
• pp.399-403
• /
• 2010

The effects of $MnO_2$ doping on the crystal structure, ferroelectric, and piezoelectric properties of (K,Na)$NbO_3$ (KNN) ceramics have been investigated. $MnO_2$ was found to be effective in enhancing the densification and grain growth during sintering. X-ray diffraction analysis indicated that Mn ions substituted B-site Nb ions up to 2 mol%, however, further doping induced unwanted secondary phases. In comparison with undoped KNN ceramics, the well developed microstructure and the substitution to B-sites in 2 mol% Mn-doped KNN ceramics resulted in significant improvements in both piezoelectric coupling coefficient and electromechanical quality factor.

• Textile Coloration and Finishing
• /
• v.27 no.3
• /
• pp.219-227
• /
• 2015

This study aims to propose a method to reduce hair damage after investigating the following: the factors which vary depending on hair treatment conditions; the degree of hair damage in the bleached sample; and an analysis of the effects of a perm on wave formation. To determine the effects of these treatment types, hair bleach was mixed with the hair treatment, and hair damage and formation of permanent waves were examined. Using a scanning electron microscope, in addition, morphological changes were analyzed and the following results were obtained: After mixing natural powder(2.5g) and hair cream(2.5g) and bleaching the mixture, it was compared to the scale structure of untreated hair. When 5g of natural powder was mixed and bleached, a clear layer was observed among cuticle scales, showing the effects of hair treatment. Therefore, this confirms that the effects of hair treatment were most notable when grain powder was mixed with hair cream. Once hair is damaged, it is almost impossible to regain its original state. When chemical agents are used, therefore, it is important to consider the possible hair damage they cause.

• Proceedings of the KIEE Conference
• /
• 1990.07a
• /
• pp.183-186
• /
• 1990

The lattice mismatch between ZnS and Si is negligible because of its value being 0.39%. In this study, $ZnS/_{(P)}Si$ solar cell were fabricated as a layer of ZnS is epitaxially grown on a silicon substrate by PVD method and its photovoltaic properties were measured and discussed. The heat treatment was done after deposition. As the temperature increased up to a certain value, the film has better perfection in crystal structure and electrical characteristics. Measurments of the change that occur in the ZnS films were made by SEM., X-ray diffraction. The optimal thickness of film showned $0.6{\mu}m$, being measured by SEM. The great improvement of the grain growth ZnS film came out after heat-treatment. The result obtained from the $ZnS/_{(P)}Si$ solar cell as follows:short circuit current; $I_{sc}=54mA/cm^2$,open voltage; $V_{oc}=400mV$, fill factor FF=0.72, conversion efficiency; ${\eta}=15.6%$ under the irradiation of 100 ($mW/cm^2$) focused by solar energy. And these are discussed in comparison with other kinds.

• Transactions of Materials Processing
• /
• v.8 no.3
• /
• pp.227-227
• /
• 1999

The effects of intermediate annealing (IA) and the final cold rolling (CR) condition on the microstructure and sagging resistance during brazing were investigated using three layer clad sheets composed of the Al-7.5 wt.%Si alloy (filler, thickness: 10 ㎛)/Al-1.3 wt.%Mn based alloy (core, 80㎛)/Al-7.5 wt.%Si alloy (filler, 10㎛). Also, the effect of 1.2∼2 wt.% Zn addition into the core on the sagging resistance of the clad sheets was determined. It was revealed that all the clad sheets fabricated by the optimum condition (IA at 690 K and CR to 20∼45%) show excellent sagging resistance with a limited erosion due to the formation of a coarsely recrystallized grain structure in the core during brazing. It was also revealed that the recrystallization behavior of the Al-1.3 wt.%Mn based alloy is hardly affected by the addition of 1.2-2 wt.%Zn during the brazing cycle. Therefore, the sagging resistance of the clad sheets is found to be governed not by the Zn content added in the A1-1.3wt.%Mn based core, but by the intermediate annealing and final cold rolling condition.

• Journal of Welding and Joining
• /
• v.3 no.2
• /
• pp.42-51
• /
• 1985

The dynamic fracture toughness, fracture characteristics, impact tension and tensile properties of Al-Mg-Si T5 alloy and Al-Zn-Mg T6 alloy respectively welded with filler metal of Alcan 4043 were investigated. The dynamic fracture toughness values were obtained rapidly and simply for the specimen of small size by using instrumented Chirpy impact testing machine. the testing temperatures of the specimen were a range of room temperature and-196.deg. C. The results obtained in this experiment are summarized as follows. With decreasing the testing temperatures, dynamic tensile stress and fracture load were increased, on the other hand the deflection and impact value showed decreasing tendency in order of base metal>HAZ>weld. Changes of total absorbed energy were more influenced by the crack propagation energy than the crack initiation energy. At the low temperatures, the unstable rapid fracture representing the crack propagation appeared for the specimens of Charpy press side notched in Al-Zn-Mg alloy, but it was difficult to obtain the unstable rapid fracture in Al-Mg-Si alloy. Because of the development of plastic zone at the notch root, it was difficult to obtain thevalid $K_{1d}$ value in Al-Mg-Si alloy. Therefore the fatigue cracked specimens were effective in both Al-Mg-Si and Al-Zn-Mg alloys. With decreasing the impact testing temperatures, specimens underwent a transition from dimple-type transgranular fracture to lamella surface-type intergranular fracture because of the precipitate at the grain boundaries, impurities and crystal structure of the precipitates.s.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.589-589
• /
• 2012

Indium sulfide thin films have been grown onto glass substrates using radio frequency magnetron sputtering at room temperature. The as-deposited film were annealed in nitrogen atmosphere at different temperatures of 100, 200, 300, 400 and $500^{\circ}C$ with an 1 h annealing time. The effect of annealing temperature on composition, structure, morphology and optical properties of the as-grown In2S3 films has been studied. The XRD results indicate that the as-deposited films are composed by a mixture of both cubic ${\alpha}$ and ${\beta}$ crystalline phases, with some fraction of tetragonal phase. The thermal annealing on the films produces the conversion of the cubic crystalline phases to the tetragonal ${\beta}$ one and a crystalline reorientation of the latter phase. The surface morphological analysis reveals that the films grown at $300^{\circ}C$ have an average grain size of ~ 58 nm. These films show a S/In ratio of 0.99. The optical band gap is found to be direct and the films grown at $300^{\circ}C$ shows a higher optical transmittance of 80% and an energy band gap of 2.52 eV.

• Korean Journal of Materials Research
• /
• v.22 no.8
• /
• pp.385-389
• /
• 2012

Significant improvements in the switching voltage distribution are required for the development of unipolar resistive memory devices using $MnO_x$ thin films. The $V_{set}$ of the as-grown $MnO_x$ film ranged from 1 to 6.2 V, whereas the $V_{set}$ of the oxygen-annealed film ranged from 2.3 to 3 V. An excess of oxygen in an $MnO_x$ film leads to an increase in $Mn^{4+}$ content at the $MnO_x$ film surface with a subsequent change in the $Mn^{4+}/Mn^{3+}$ ratio at the surface. This was attributed to the change in $Mn^{4+}/Mn^{3+}$ ratios at the $MnO_x$ surface and to grain growth. Oxygen annealing is a possible solution for improving the switching voltage distribution of $MnO_x$ thin films. In addition, crystalline $MnO_x$ can help stabilize the $V_{set}$ and $V_{reset}$ distribution in memory switching in a Ti/$MnO_x$/Pt structure. The improved uniformity was attributed not only to the change of the crystallinity but also to the redox reaction at the interface between Ti and $MnO_x$.

• Journal of Powder Materials
• /
• v.27 no.5
• /
• pp.414-419
• /
• 2020

In the present study, we investigated the austenite stability of a sintered Fe-based nanocrystalline alloy. The volume fraction of austenite was measured based on the X-ray diffraction data of sintered Fe-based nanocrystalline alloys, which were prepared by high-energy ball milling and spark plasma sintering. The sintered alloy samples showed a higher volume fraction of austenite at room temperature as compared to the equilibrium volume fraction of austenite obtained using thermodynamic calculations, which resulted from the nanosized crystalline structure of the sintered alloy. It was proved that the austenite stability of the sintered Fe-based alloy increased with a rise in the amount of austenite stabilizing elements such as Mn, Ni, and C; however, it increased more effectively with a decrease in the actual grain size. Furthermore, we proposed a new equation to predict the martensite starting temperature for sintered Fe-based alloys.

• Journal of Korea Foundry Society
• /
• v.15 no.5
• /
• pp.514-522
• /
• 1995

The microstructural evolution with isothermal stirring during semi-solid state processing of hypoeutectic Al-6.2wt%Si alloy was studied. Substructure of the individual primary solid particle in the slurry was investigated through transmission electron microscopy(TEM). Formation of subgrain boundaries on the rheocast Al-6.2wt%Si alloy is observed and the misorientation between the grains is shown typically under 2 degrees by analyzing selected area diffraction (SAD) and convergent beam electron diffraction (CBED) patterns. The existence of high angle grain boundaries are also observed in the alloy. Based upon these observations, mechanisms for the primary particles fragmentation are considered. With isothermal stirring, the dislocation density increases, and the evolution of dislocation cell structure takes place, which is interpreted as a process of achieving uniform deformation by dynamic recovery under applied shear stress.