• Journal of Biosystems Engineering
• /
• 제41권4호
• /
• pp.408-417
• /
• 2016

Purpose: Yield monitoring systems are an essential component of precision agriculture. They indicate the spatial variability of crop yield in fields, and have become an important factor in modern harvesters. The objective of this paper was to review research trends related to yield monitoring sensors for grain crops. Methods: The literature was reviewed for research on the major sensing components of grain yield monitoring systems. These major components included grain flow sensors, moisture content sensors, and cutting width sensors. Sensors were classified by sensing principle and type, and their performance was also reviewed. Results: The main targeted harvesting grain crops were rice, wheat, corn, barley, and grain sorghum. Grain flow sensors were classified into mass flow and volume flow methods. Mass flow sensors were mounted primarily at the clean grain elevator head or under the grain tank, and volume flow sensors were mounted at the head or in the middle of the elevator. Mass flow methods used weighing, force impact, and radiometric approaches, some of which resulted in measurement error levels lower than 5% ($R^2=0.99$). Volume flow methods included paddle wheel type and optical type, and in the best cases produced error levels lower than 3%. Grain moisture content sensing was in many cases achieved using capacitive modules. In some cases, errors were lower than 1%. Cutting width was measured by ultrasonic distance sensors mounted at both sides of the header dividers, and the errors were in some cases lower than 5%. Conclusions: The design and fabrication of an integrated yield monitoring system for a target crop would be affected by the selection of a sensing approach, as well as the layout and mounting of the sensors. For accurate estimation of yield, signal processing and correction measures should be also implemented.

• 한국인쇄학회지
• /
• 제8권1호
• /
• pp.21-53
• /
• 1990

In analysing the Image quality, one of the most important things to be considered is the granularity at a given emulsion speed. To enhance the image quality, the granularity should be lowered by the suitable methods, such as controlling the design of emulsion, grain size and structure, the distribution state of grains in the emulsion, etc. In this paper, the relations between the AgX grain structure and granularity are studied as a way of lowering granularity. According to the results, it is found that the grain structure is a very important factor for determining the granularity characteristics.istics.

• 한국주조공학회지
• /
• 제30권5호
• /
• pp.187-195
• /
• 2010

In this study, in order to obtain a useful guide line for design and production of automotive heat exchanger components made of 4343/3003/4343 aluminum clad sheets, it was aimed to improve the understanding about the grain refinement effect on brazing characteristic of the clad sheets. Al-10Ti master alloy was used for grain refinement of 3003 core alloy, and the Ti inoculation level was systematically changed up to 0.1 wt%. The three-layer aluminum clad sheets were fabricated by hot roll bonding process. The effect of grain refinement on brazing characteristic of the clad sheets was investigated by evaluating wettability, bonding strength and sagging resistance.

• 한국가구학회지
• /
• 제21권2호
• /
• pp.188-195
• /
• 2010

This study has been focused on the evaluation of domestic softwood timbers to replace imported timbers for woodcrafts and furniture-making. Figures on radial and tangential sections were observed with naked eyes. As the result of study on the figures appeared on the wood surface of 6 species of trees, flat grain and edge grain were clearly found from Taxus cuspidata. Juniperus chinensis and Ginkgo biloba had wavy grain figure and pigment figure, and blister figure was found in Pinus densiflora, Larix kaempferi showed pitch streak and irregular figures on its tangential section due to growth abnormalities. Wavy grain figure appeared weakly on near knot of Pinus koraiensis. The characteristic figures shown from each species of trees are expected to be used for crafts, sculptures, furniture, and interior decoration. They are also considered to have great potential to substitute imported timber sufficiently, which are currently used a lot for wood crafts and furniture-making.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.365-366
• /
• 2010

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.107-110
• /
• 1999

The purpose of this research is for the development of a new type forging equipment H.C.G(Hyundai Continuous Grain-flow) by using two virtual build-up tools rigid viscoplastic FEM and downsized plasticine experiment. This forging equipment consists of consecutive horizontal and vertical pressure while the traditional forging method consists of only vertical pressure. Using this method high quality crankshafts can be forged as it can maintain a continuous grain flow. The factors considered in the development of equipment are die geometry for flawless deformed shape die reaction forces stress/strain distributions and continuous material flow. We carried out several numerical simulations and downsized plasticine experiments for the proper design of the forging equipment. The validity of those simulation results is confirmed by checking with the actual test results. Based on these simulation results the proper design of the H.C.G for ging equipment is enabled.

• 소성∙가공
• /
• 제8권3호
• /
• pp.237-244
• /
• 1999

The purpose of this research is for the development of a new type forging equipment. H.C.G.(Hyundai Continuous Grain-Flow), by using two virtual build-up tools, rigid viscoplastic FEM and downsized plasticine experiment. This forging method consists of only vertical pressuree. Therefore, high quality crankshafts can be forged with this method as it can maintain a continuous grain flow. The factors considered in the development of equipment are die geometry for flawless deformed shape, die reaction forces, stress/strain distributions and continuous material flow. We carried out several numerical simulations and downsized plasticine experiments for the proper design of the forging equipment. The validity of those simulation results is confirmed by checking with the actual test results. Based on these simulation results, the proper design of the H.C.G. forging equipment is enabled.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.205-209
• /
• 2010

The technology of production of the thermoplastic composite rocket propellants is based on a two-phase production procedure. The first phase represents the production of a semi-product in the sheet (foil) form (thickness: 0.5 mm ~ 5 mm), whereas the second phase is realized independently from the first one and it is based on the semi-produced product and thus the final form of the propellant grain is realized in relation to the defined geometry. Well done mechanical characteristics of the propellant grain enable that the same thing could be used as a mandrel in the filament winding procedure in creating the motor chamber of the composite material.

• 한국가구학회지
• /
• 제25권1호
• /
• pp.36-44
• /
• 2014

This study was investigated to sensible characteristic and physical characteristic to estimate value of the craft for Pinus densiflora and Pinus densiflora for. erecta Uyeki wood. The sensual characteristics of wood are evaluated by wood figure, wood grain, odor, and the physical characteristics by weathering, abrasion, surface roughness and hardness. The wood figure of these species were observed at flat grain in the radial section and edge grain in the tangential section. Also, burl's figure was observed in Burl of Pinus densiflora wood. Pinus densiflora for. erecta Uyeki wood had volatile aroma compounds such as Camphene, Thymyl ether, ${\alpha}$-Longipinene, etc. Pinus densiflora wood had volatile aroma compounds such as ${\alpha}$-Longipinene, (+)-Cedrol, etc. The moisture soption, abrasion, hardness and roughness were very different between the two species.

• 열처리공학회지
• /
• 제31권2호
• /
• pp.56-62
• /
• 2018

Many researchers have studied on the precipitation control after solution treatment to improve the damping capacity without decreasing the strength. However, studies on the damping capacity and microstructure changes after deformation in the solid solution strengthening alloys were inadequate, such as the Al-Zn series magnesium alloys. Therefore, in order to investigate the effect of annealing condition on microstructure change and damping a capacity of AZ61 magnesium alloy. In this study, it was confirmed that the microstructure changes affect the damping capacity and hardness when annealed AZ61 alloy. AZ61 magnesium alloy was rolled at $400^{\circ}C$ with rolling reduction of 30%. These specimens were annealed at $350^{\circ}C$ to $450^{\circ}C$ for 30-180 minutes. After annealing, microstructure was observed by using optical microscopy, and damping capacity was measured by using internal friction measurement machine. Hardness was measured by Vickers hardness tester under a condition of 0.3 N. In this study, static recrystallization was observed regardless of the annealing conditions. In addition, uniform equiaxed grain structure was developed by annealing treatment. Hardness is decreased with increasing grain size. This is associated with Hall-Petch equation and static recrystallization. In case of damping capacity, bigger grain size show the larger damping capacity.