• 한국재료학회지
• /
• 제23권11호
• /
• pp.649-654
• /
• 2013

The effect of interstitial elements on the ductile-brittle transition behavior of austenitic Fe-18Cr-10Mn-2Ni alloys with different nitrogen and carbon contents was investigated in this study. All the alloys exhibited ductile-brittle transition behavior because of unusual low-temperature brittle fracture, even though they have a faced-centered cubic structure. With the same interstitial content, the combined addition of nitrogen and carbon, compared to the sole addition of nitrogen, improved the low-temperature toughness and thus decreased the ductile-brittle transition temperature (DBTT) because this combined addition effectively enhances the metallic component of the interatomic bonds and is accompanied by good plasticity and toughness due to the increased free electron concentration. The increase in carbon content or of the carbon-to-nitrogen ratio, however, could increase the DBTT since either of these causes the occurrence of intergranular fracture that lead to the deterioration of the toughness at low temperatures. The secondary ion mass spectroscopy analysis results for the observation of carbon and nitrogen distributions confirms that the carbon and nitrogen atoms were significantly segregated to the austenite grain boundaries and then caused grain boundary embrittlement. In order to successfully develop austenitic Fe-Cr-Mn alloys for low-temperature application, therefore, more systematic study is required to determine the optimum content and ratio of carbon and nitrogen in terms of free electron concentration and grain boundary embrittlement.

• 터널과지하공간
• /
• 제31권4호
• /
• pp.270-288
• /
• 2021

본 연구에서는 입자기반 개별요소모델(grain-based distinct element model, GBDEM)을 이용하여 암석 균열의 역학적, 수리적 거동을 평가할 수 있는 수치해석기법을 제시하고 해석해와의 비교를 통해 검증하였다. 이는 DECOVALEX-2023 프로젝트 Task G의 일환으로 수행된 벤치마크 모델링 연구로, Task G는 결정질 암반 내 균열의 열-수리-역학적 복합거동을 해석하기 위한 수치해석기법을 개발하는 데에 목표가 있다. 본 연구에서는 사면체 개별 입자들을 이용하여 해석모델을 생성하고 3DEC을 이용하여 입자와 접촉에서의 거동을 해석하였다. 이 과정에서 등가연속체 개념을 적용해 입자기반모델의 미시물성을 산정할 수 있는 새로운 기법을 제시하였다. 한편, 균열 경사각과 거칠기, 경계응력조건 및 압력 조건에 따른 해석을 실시하여 각 해석조건이 균열의 수직, 전단방향 거동에 미치는 영향을 살펴보았다. 해석 결과, 제안된 수치모델은 경계응력에 따른 균열의 미끄러짐(fracture slip)과 유체 압력에 따른 균열의 개방(fracture opening), 균열 경사에 따른 응력 분포, 거칠기로 인한 전단변위의 구속 등을 합리적으로 재현하고 있음을 확인하였다. 수치해석을 통해 계산된 균열의 수직방향, 전단방향 변위는 모두 해석해를 통해 계산된 값과 거의 일치하는 결과를 보였다. 본 연구의 해석모델은 Task G에 참여하는 국외 연구팀들과의 의견 교류와 워크숍을 통해 지속적으로 개선하는 한편, 향후 다양한 조건의 실내시험에 적용하여 타당성을 검증할 예정이다.

• 센서학회지
• /
• 제9권1호
• /
• pp.76-82
• /
• 2000

본 연구에서는 내부전극 접합기술을 이용하여 적층구조의 PTC 서미스터를 제작하였다. 적층구조 PTC 서미스터는 저항, 소형, 대전류 등의 특징을 갖는다. PTC 특성을 조사하기 위하여 첨가제효과, 전압-전류특성, 온도특성, 복합임피던스 특성 등을 측정하였다. 적층구조 PTC서미스터는 저항의 온도특성과 전압-전류특성에서 높은 비선형성을 나타내었다. 적층수가 증가함에 따라 상온저항이 감소되는 특성이 결정립의 효과에 기인됨을 알았다. 전류의 스윗칭 변화는 적층구조가 갖는 열용량의 크기에 비례하였으며, 적층수가 증가할수록 스윗칭 시간이 증가하였다.

• 소성∙가공
• /
• 제22권8호
• /
• pp.450-455
• /
• 2013

In the current study, a new dynamic recrystallization model for predicting high temperature flow stress is developed based on a physical model and the mean field theory. In the model, the grain aggregate is assumed as a representative volume element to describe dynamic recrystallization. The flow stress and microstructure during dynamic recrystallization were calculated using three sub-models for work hardening, for nucleation and for growth. In the case of work hardening, a single parameter dislocation density model was used to calculate change of dislocation density and stress in the grains. For modeling nucleation, the nucleation criterion developed was based on the grain boundary bulge mechanism and a constant nucleation rate was assumed. Conventional rate theory was used for describing growth. The flow stress behavior of pure copper was investigated using the model and compared with experimental findings. Simulated results by cellular automata were used for validating the model.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.188-191
• /
• 2000

The properties of piezoelectric and dielectric for 0.05Pb(Mn$\_$0.4/W$\_$0.2/Nb$\_$0.4/)O$_3$ - 0.95PbZr$\_$x/Ti$\_$1-x/O$_3$ compositions have been investigated. In the composition of 0.05Pb(Mn$\_$0.4/W$\_$0.2/Nb$\_$0.4/)O$_3$ - 0.95PbZr$\_$0.51/Ti$\_$0.49/O$_3$, the values of k$\_$p/ and $\varepsilon$$\_$33/$\^$T// $\varepsilon$$\_$0/ are maximized, but Q$\_$m/ was minimized (k$\_$p/=56.5[%], Q$\_$m/=1130, d$\_$33/=258[pC/N], $\varepsilon$$\_$33/$\^$T// $\varepsilon$$\_$0/=1170). The grain size was suppressed and the uniformity of grain was improved at the 1100[˚C]. Also, we can see the dielectric constants variations between the before poling and after poling. This effect results from the effect(increase element of dielectric constants) between dipole switching and electrostriction inducing stress and dipole direction to the poling orientation(decrease element of dielectric constants). At x=0.51, we can find MPB(morphotropic phase boundary).

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권5호
• /
• pp.660-669
• /
• 1998

In this paper the Hardness and Electro-chemical corrosion of the Nimonic 80A superalloy were studied. It aging heat treatments was carried out at $650^{\circ}C$, $700^{\circ}C$, $750^{\circ}C$,$800^{\circ}C$ and $850^{\circ}C$ with different time of 20min , 30min 1hour, 2hours, 4hours, and 16hours additionally 64hours and 128hours at $650^{\circ}C$. The obtained results were as follows; 1. As aging temperature increased the time for the maximum hardness was reduced from 128hours at $650^{\circ}C$ to 30min at $850^{\circ}C$ whereas the highest hardness was reduced from Hv 381 at $650^{\circ}C$ to Hv 321 at $850^{\circ}C$. 2. In the Electro-chemical corrosion test as a function of aging heat treatment time and tem-perature the corrosion potential was reversely proportional to Hardness which indicated the effects of ${\gamma}/{\gamma}'$ coherency of base material and precipitate. 3. Initiation point of the pitting was observed at grain boundary twin boundary and near${\gamma}'$ pre-cipitates. The results of composition analysis by EDS at this point indicated that sulphur originat-ed from 1N $H_2SO_4$ solution was found in depletion at the grain boundaries and the pit which arouse in the near precipitates were lack of Al Ti and Ni which are the main element of ${\gamma}'$ The depletion of such element was cause breakdown of passive film.

• 한국재료학회지
• /
• 제25권11호
• /
• pp.607-611
• /
• 2015

The microstructural evolution of Grade 91 tempered martensite ferritic steels heat treated at $760{\sim}1000^{\circ}C$ for two hours was investigated using scanning electron microscopy(SEM), energy disperse spectroscopy(EDS), electron backscattered diffraction (EBSD), and transmission electron microscopy(TEM); a microhardness tester was also employed, with a focus on the grain and precipitate evolution process as well as on the main hardening element. It was found that an evolution of tempered martensite to ferrite($760{\sim}850^{\circ}C$), and to fresh martensite($900{\sim}1000^{\circ}C$), occurred with the increase of temperature. Simultaneously, the parabolic evolution characteristics of the low angle grain boundary(LAGB) increased with the increase of the heating temperature(highest fraction of LAGB at $925^{\circ}C$), indicating grain recovery upon intercritical heating. The main precipitate, $M_{23}C_6$, was found to be coarsened slightly at $760{\sim}850^{\circ}C$; it then dissolved at $850{\sim}1000^{\circ}C$. Besides this, $M_3C$ cementite was formed at $900{\sim}1000^{\circ}C$. Finally, the experimental results show that the hardness of the steel depended largely on the matrix structure, rather than on the precipitates, with the fresh martensite showing the highest hardness value.

• Journal of Welding and Joining
• /
• 제21권4호
• /
• pp.69-74
• /
• 2003

The mechanical properties of STD11 Joints by using TLP (Transient Liquid Phase Diffusion) bonding method employing MBF-30 and MBF-80 insert metals were investigated with concerning to the microstructural change. TLP bonding of STD 11 was carried out at 1323∼1423K for 0.6ks∼3.6ks in vacuum. The microstructure and the element distribution of the interlayer between tool steels and insert metals showed specific feature with bonding conditions. It was found that the width of the interlayer increased at initial bonding stage. However, the width of interlayer showed nearly constant value during the isothermal solidification. After isothermal solidification was completed, the joint showed homogeneous element distribution and similar microstructure with base metal because of the grain boundary migration to the bonded interlayer. The bonding strength measured by a tensile test has been varied with the bonding conditions. The maximum joint strength, 760MPa, was obtained with the condition of 1423K for 1.2ks using MBF30 insert metal in this experiment.

• 한국정밀공학회지
• /
• 제18권9호
• /
• pp.101-109
• /
• 2001

The simulated die casting process in which the traditional plaster casting process is combined with rapid prototyping technology is being used to produce Al, Mg and Zn die casting prototypes. Because of lower mechanical properties induced by the large grain structure and incomplete filling, conventional plaster casting is not suitable for the simulated die casting process. A plaster casting process with pressurized vibration was developed for the simulated die casting process[5]. In this paper, numerical simulation for the filling stage of the process has been performed to show the effect of the pressurized vibration for complete filling. Treatment of boundary condition based on the finite element method has been proposed for imparted pressurized vibration in the plaster casting process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.64-67
• /
• 2000

Element distribution analysis and degradation characteristics of the ZnO varistors fabricated at the ambient sintering-process is investigated in this study. ZnO varistors made of Matsuoka's composition were fabricated by standard ceramic techniques. The ambient sintering-process is performed at the special electrical-furnace which is equipped with the vacuum system. The Gases of injection at sintering- process were oxygen, air, nitrogen and argon respectively. Element and quantitative analysis in the microstructure of ZnO varistors made use of EPMA equipment. Degradation characteristics were showed by DC degradation tests at $115{\pm}2\;^{\circ}C$ for period up to 13 h. From above analysis, it is found that at the DC degradation test the ZnO varistor sintered in oxygen atmosphere showed the excellent prop properties among them and these results could be explain by element and quantitative analysis in ZnO microstructure.