• Journal of Korean Society of Forest Science
• /
• v.95 no.1
• /
• pp.102-112
• /
• 2006

The change of species composition and stand structure along altitudinal gradients in different aged stands was studied in five natural stands located each at 400 m, 800 m, 1,000 m, and two at 1,300 m above sea level (asl) in the western part of Mt. Chiri in Korea. Trees larger than 2.5 cm DBH were inventoried in 3 to 8 $20m{\times}20m$ quadrats in each study site. Stand ages were estimated based on the ages of Pinus densiflora Siebold & Zucc. and Abies koreana Wilson, and used to analyze the changes in species composition and stand structure including diameter and height distributions. Species composition was changed along altitudinal gradients as P. densiflora dominated stands at 400 m asl while A. koreana dominated stands at 1,300 m asl. Major species of Quercus also changed along altitudinal gradients as Quercus variabilis Blume at 400 m asl, Quercus serrata Thunb. ex Murray at 800 m asl, and Quercus mongolica Fisch. ex Ledeb. at higher than 1,000 m asl. The diameter distribution did not show significant differences among stands of different altitudes. However, the height distributions of upper crown layers were significantly different among stands at below and above 1,000 m as) (P < 0.0001). Trees taller than 20 m rarely appeared in stands over 1,000 m asl. P. densiflora dominant stands at 400 m asl developed two clumped age groups as one in 30-40 ages and the other around 70 years old. Q. serrata dominant stands at 800 m asl, Q. mongolica dominant stands at 1,300 m asl and A. koreana dominant stands at 1,300 m asl were estimated to be around 30, 70, and over 140 years old after major disturbances, respectively. The diameter distribution with age structure indicated that P. densiflora at 1,300 m asl might be replaced by Q. mongolica, and Q. mongolica might be replaced by A. koreana and Pinus koraiensis later. A. koreana dominant stand seemed to stay its dominance quite long if the large disturbance would be absent.

• Journal of Korean Society of Forest Science
• /
• v.85 no.1
• /
• pp.107-119
• /
• 1996

To understand vegetation changes along environmental gradients in the natural forests in the east side of the Cascade Range in Washington state, USA, line transects were used to sample six different forest environments in the Wenatchee National Forest in the north-facing and south-facing sites at 975, 1280 and 1700m elevation. Data were analyzed using ordination by detranded correspondence analysis. Pseudotsuga menziesii was found as one of the dominant species on all the six sites regardless of elevation or aspect, while Pinus ponderosa was dominant on south slopes only. Abies grandis and A. lasiocarpa were dominant species on north slopes at elevations of 1280 and 1700m, respectively. Moisture, as it related to aspect, was identified as one of the most important environmental gradients for explaining the variation of vegetation types. On north-facing slopes, compared to south-facing slopes, where moisture was not as limiting and canopies could grow denser, probably, elevation or competitive interaction was more important. Species diversity tended to decrease with increasing environmental severity, with south slopes having less diversity than north slopes due to extended water stress and harsher temperature extremes on south slopes. The age structure on north-facing and south-facing slopes was different. Light intensity, moisture and climate were different between these two slopes. Large scale disturbances(e.g., big fire or insects) were major causes in changing age structure. Younger trees showed a closer relationship between size and age than adult trees. DBH values of shade intolerant species in south-facing slope were bigger than those of north-facing slope, which suggested that aspect of stands be the most important factor for age and size.

• Fibers and Polymers
• /
• v.7 no.4
• /
• pp.432-435
• /
• 2006

High Modulus and high tenacity polypropylene fibers have been prepared by drawing on a gradient heater. Results show that fiber properties are significantly affected by temperature profiles of final stage drawing on a gradient heater. The gradient drawn filaments showed superior mechanical properties when compared to filaments drawn over a constant temperature heater. Fibers with initial modulus of 16.4 GPa and tenacity of 670 MPa have been manufactured in the process. The nature of the gradient drawing had a significant effect on end properties. The superior mechanical properties are attributed to the high crystal perfection and crystallinity and low void fractions obtained at high draw ratios when drawn over a gradient heater.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.1
• /
• pp.24-34
• /
• 1985

The study of unsteady gas exchange processes in the inlet and exhaust systems of the single-cylinder 4-stroke cycle spark ignition engine is presented in this paper. The generalized method of characteristics including friction, heat transfer, change of flow area and entropy gradients was used for solving the equations defining the gas exchange process. The path line calculation was also conducted to allow for calculation of the gas composition and entropy change along the path lines, and of the variable specific heat due to the change of temperature and composition. As the result of the simulation, the properties at each point in the inlet and exhaust pipe, pressure and temperature in the cylinder, and charging efficiency were obtained. Pumping loss and residual gas fraction were also computed. The effect of engine speed, exhaust and inlet pipe length on the pumping loss and charging efficiency were studied showing that the results were in agreement with what has been known from experiments.

• Geotechnical Engineering
• /
• v.11 no.3
• /
• pp.37-42
• /
• 1995

The laboratory hydraulic conducti vita tests with rigid wall permeameter were performed to study the effects of waste leachate on the permeability of a marine clay. The marine clay and waste leachate for this study were sampled from Kimpo Wastefills, and the hydraulic gradients applied to the clay specimens aTe relatively high from 37.5 to 225. The test results show that the permeability of a marine clay is increased with increasing the concentration of leachate and with decreasing the hydraulic gradient. And also both the liquid limit and the plasticity index of the marine clay miRed with waste leachate decrease with increasing the concentration of leachate.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.150-153
• /
• 2003

Microwaves belong to the portion of the electromagnetic spectrum with frequencies between 300MHz and 300GHz.$\^$1)/ In microwave processing, the energy is delivered directly to materials through molecular interaction with the electromagnetic field. This result in rapid heating throughout the material thickness with the reduced thermal gradients. If microwave is applied to fibrous materials, it can be reduced processing time. (omitted)

• Clinical and Experimental Reproductive Medicine
• /
• v.11 no.2
• /
• pp.69-76
• /
• 1984

In order to obtain high proportion of Y sperm the semen was laid over 6%,10% and 20% bovine serum albumin. Separated sperm were stained with quinacrine mustard in order to see F - body which could be seen in human Y sperm. But we could'nt find F-body in the bull sperm. So sperm were compared with size of sperm head. As a result of observation separated sperm was small in size of length and width of sperm head as compared with control sperm. So it was found that the proportion of Y sperm showed a marked increase in separated layer. Then the higher albumin density was, the higher the proportion of Y sperm which had smaller head and faster motility was. But the higher albumin density was, the lower the recovery rate of sperm was. So it was hard to separate Y sperm in oligospermia.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.06a
• /
• pp.211-218
• /
• 2000

Hot spot behaviors on the disk-pad contact surface during a braking operation have been analyzed for a ventilated disk brake using the finite element method. Hot spots which were studied using a coupled thermal-mechanical analysis technique are influenced by all of the mechanical, thermal, elastic and plastic processes that are involved in braking cycles, but their temperature gradients are most affected by rubbing speeds, braking forces, and design parameters between the disk and the pad. Undesirable hot spots that are generated by local thermoelastic instabilities are intended to be removed by optimized design parameters and material properties. In this study, a three-dimensional numerical method for the demonstration of hot spot behaviors has been applied to the rubbing surfaces between the disk and the pad.

• International Journal of Railway
• /
• v.2 no.2
• /
• pp.70-79
• /
• 2009

An optimal driving strategy of a train in a long journey on a nonsteep track has four phases: an initial power phase, a long hold speed phase, a coast phase and a final brake phase. The majority of the journey is speed holding. On a track with steep gradients, it becomes necessary to vary the strategy around steep sections of track because it is not possible to hold a constant steep on steep track. Instead we must interrupt the speed hold phase with a power phase. The aim of this paper is to show that there is a unique power phase that satisfies the necessary conditions for an optimal journey. The problem is developed and solved for various cases, from a simple single steep gradient to a complicated multiple steep gradient section. For each case, we construct a set of new conditions for optimality of the power phase that minimises the energy used during the power phase subject to a weighted time penalty. We then use the new necessary conditions to develop a calculate scheme for finding an optimal power phase for a steep incline. We also present an example to confirm the uniqueness of an optimal power phase.

• Proceedings of the Korean Information Science Society Conference
• /
• 2004.10b
• /
• pp.283-285
• /
• 2004

단백질 2차원 전기영동은 다양한 단백질 분리 방법 중 가장 널리 쓰이는 방법으로 실험 결과를 촬영한 영상을 분석하여 얻은 단백질 스팟의 위치나 질량, 발현 유무 등을 이용하여 각종 질병의 발생 원인 진행 상태, 생리적인 변화 등에 대해 분석할 수 있다. 실험 영상에 다수의 단백질이 존재하므로 이를 수작업으로 처리할 경우에 많은 시간과 노력이 소요되므로 본 논문에서는 자동화된 단백질 스팟 검출 방법을 제안하였으며 단백질 스팟이 같은 위치에 겹쳐서 나타나는 경우가 많은 단백질 2차원 전기영동 실험 영상의 특성을 고려하여 여러 개의 단백질이 겹쳐진 복잡한 스팟 영역에 대해서 스팟의 형태 정보를 이용하여 스팟의 개수를 추정하고 개별 스팟으로 분리하여 보다 신뢰성 있는 분석이 가능하게 하였다 본 논문에서 제안된 방법의 효용성을 검증하기 위해 기존에 널리 사용되고 있는 상용 소프트웨어와 비교 실험을 수행한 결과 겹친 정도가 60%이상인 경우 기존 방법에 비해 우수한 결과를 보였다.