• Transactions of Materials Processing
• /
• v.29 no.1
• /
• pp.27-36
• /
• 2020

The Goss texture component of {110}<001> is well known as one of the best texture components to improve the magnetic properties of electrical steel sheets. The small amount of the Goss texture component is obtained at the surface of the steel sheet by shear deformation due to friction between the steel sheet and the roll during conventional symmetric rolling. This study aims to identify a method to obtain high intensity of the Goss texture component not only at the surface but in the whole layer of the steel sheet by shear deformation of asymmetric rolling. Low carbon steel sheets, which have different initial texture, were asymmetrically rolled by about 50%, 70%, and 80%. The pole figures of the top, center, and bottom layers of the initial and asymmetrically rolled low carbon steel sheets were measured by an X-ray diffractometer. Based on the measured pole figures of these samples, the intensities of the main texture components were analyzed for the initial and asymmetrically rolled low carbon steel sheets. As a result, the initial low carbon steel sheet with the γ-fiber component showed a higher intensity of the Goss texture component in the whole layer than the steel sheet with other texture components after asymmetric rolling.

• Transactions of Materials Processing
• /
• v.26 no.3
• /
• pp.150-155
• /
• 2017

To obtain the Goss texture, {110}<001>, IF steel sheets were asymmetrically rolled by 50-89% reduction in the thickness at room temperature and subsequently annealed at 200, 900, and $1200^{\circ}C$ in a box furnace under air atmosphere. The asymmetrically rolled specimens and annealed specimens show well-developed Goss texture, {110}<001>. After the IF steel sheets were asymmetrically rolled at room temperature and subsequently annealed at $900^{\circ}C$ for 1 h in a box furnace under air atmosphere, the intensity of the Goss texture, {110}<001> was high in the IF steel sheets.

• Metals and materials international
• /
• v.24 no.6
• /
• pp.1369-1375
• /
• 2018

In Fe-3%Si steel, the hot rolling process affects not only the hot rolling texture but also the primary recrystallization texture. Here, the effect of asymmetric hot rolling was studied by comparing the difference in the texture evolved between asymmetric and symmetric hot rolling. The effect of asymmetric hot rolling on the texture of primary recrystallized Fe-3%Si steel was also studied. The symmetric hot rolling of Fe-3%Si steel produces a rotated cube texture at the center but Goss and copper textures near the surface. Asymmetric hot rolling tends to produce Goss and copper textures even at the center like the texture near the surface. After primary recrystallization, the dominant texture at the center changes from {001} <210> to {111} <112> and the new texture has a higher fraction of the grains which make the low energy boundary with Goss grains than that of symmetric hot rolling.

• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.6
• /
• pp.269-274
• /
• 2018

Grain-oriented electrical steel sheets are mainly used as core materials for transformers and motors. They should have excellent magnetic properties such as low core loss, high magnetic flux density and high permeability. In order to improve the magnetic properties of the electrical steel sheet, it is important to form Goss oriented grains with a very strong {110}<001> orientation. Recently, efforts have been made to develop Goss grains by controlling processes such as hot rolling, cold rolling, and primary and secondary recrystallization. In this study, the sheets containing 3.2 and 3.4wt.% Si were used, which were rolled with 1 and 10 passes with total thickness reduction of 89%. Heating was carried out for primary recrystallization with different heating rates of $25^{\circ}C/s$ and $24^{\circ}C/min$ until $720^{\circ}C$. The behavior of Goss-, {411}<148>-, and {111}<112>-oriented grains were analyzed using X-ray diffraction(XRD) and electron back-scatter diffraction(EBSD) analysis. The area fraction of Goss-oriented grains increased with the number of rolling passes during cold rolling; however, after the primary recrystallization, the area fraction of the Goss grains was higher and exact Goss grains were found in the specimens subjected to rapid heating after one rolling pass.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.303-306
• /
• 1997

$\alpha$형과 $\beta$형 섬유조직의 압연 집합조직을 초기 집합조직으로 갖는 알루미늄 판재의 디프드로잉 공정시 집합조직 변화를 고찰하였다. 플랜지 변형 단계에서는 Bs성분은 감소하 였으며, Goss, Cu, P등의 성분들은 증가하였다. 컵의 윗쪽에서는 아랫쪽에 비하여 Goss, Cu 성분은 증가하고 P성분의 변화는 적었다. 이는 컵의 윗쪽에서는 플랜지에서 받은 평면변형 의 정도가 컵의 아랫쪽에 비하여 크기 때문이다. 실제 디프드로잉 공정에서의 변형량에서는 결정들이 안정방위로의 회전경로인 $\alpha$D형의 섬유와 $\beta$D형의 섬유로 이동하게 된다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.08a
• /
• pp.126.3-126
• /
• 1998

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.341-341
• /
• 2005

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.4
• /
• pp.57-61
• /
• 2001

The {111}<112> deformation torture, which originated from the {110}<00l> texture near the surface of hot bands, is not prerequisite for the recrystallized {110}<001> Goss texture. During final annealing, surface-energy-induced selective growth of grains urn at the strip surface of 3%Si-Fe alloys containing 6ppm bulk content of sulfur. With decreasing final reduction, the probability that Goss grains survive under the highly segregated sulfur atmosphere and have a chance for later surface-energy-induced selective growth becomes higher, resulting in high magnetic induction.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.85-88
• /
• 1997

The effect of lubrication on the evolution of the cold rolling texture in low carbon steels was studied by X-ray texture measurement. The cold rolling texture was inhomogeneous through the thickness of the rolling sheet. The type and sharpness of the texture through the thickness and the degree of inhomogeneity were found to be dependent on the friction acting between rolls and the rolled materials. The degree of the through thickness inhomogeneities was higher in the specimen rolled without lubrication. The friction acting on the roll surface led to the formation of the Goss-Orientation in the rolling texture.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.917-920
• /
• 2001

Effects of addition of manganese and final reduction on segregation behavior of sulfur and final mangetic induction during final annealing have been investigated in the 300 ppm sulfur-contained 3% silicon-iron alloy strips with or without manganese. At the same concentration of sulfur, lower final reduction is favorable for final Goss texture. This is because the probability that the initial Goss grains survive under the highly segregated sulfur atmosphere and grow selectively within the segregated sulfur-free time range becomes higher. In the case of 3% silicon-iron with manganese, much lower magnetic induction was obtained, although the weak final reduction of 30% is given to the alloy, comparative to the 40%. This is because MnS particles acted as an reducer in the primary grain size.