• Journal of Korean Society of Forest Science
• /
• v.76 no.3
• /
• pp.193-199
• /
• 1987

Simple estimating method of rock drilling and blasting work size is necessary to apply as a guidance of general road plan and a cost analysis of mountain forest road construction. For this work study, 11 cycles were divided in 5km route at Hyeonnammeon Yangyang-gun and the mountain slope at every 20m interval was measured. During working days all kind of works concerned on drilling and blasting was investigated in every cycle. Depending on the simple work study results it's work size can bef estimated with high correlation between drilling length in meter and frequency percentage of mountain slope more than 70%. With total drilling length known the machinery hours, drillers and explosive quantify can be estimated by the regression with high correlation. Estimation of drilling and blasting work by mountain slope gradient in road route is proposed like table 5 with estimating value of machinery hour, drillers and explosive in granite gneiss region.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.2
• /
• pp.65-74
• /
• 2002

The measurement of in-situ stress is essential to estimate the ground displacement and the stress distribution of a tunnel and an underground structure. In this study, the in-situ stress distribution of the Southern Korean peninsula was re-evaluated by the new 380 in-situ data which were determined by overcoring and hydrofracturing methods, and the three-din erosional numerical analysis of tunnelling was performed. The results of in-situ stress distribution show that the distribution of horizontal stress tends to be more irregular in metamorphosed(gneiss) and granite areas than in sedimentary and volcanic areas. The ratio of horizontal to vertical stresses(K-value) in volcanic area is less than 1 below the depth of 150m. The direction and magnitude of three dimensional in-situ stresses were shown simultaneously in a figure for the first time in Korea. The three-dimensional numerical analysis of tunnelling indicates that the orientation and magnitude of displacement around a tunnel are controlled mainly by the difference between the maximum and minimum horizontal stresses.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.57-64
• /
• 2005

Since the allowable bearing capacities of piles in weathered/fractured rock are mainly governed by settlement, the load-displacement behavior of the rock socketed pile should be well known. To predict pile head settlement at the design stage, the exact understanding of the load-transfer mechanisms is essential. Therefore, in this research, the load-transfer mechanisms of drilled shaft socketed into weathered rock was investigated. For that, 5 cast-in-place concrete piles with diameters of 1,000 mm were socketed into weathered gneiss. The static axial load tests and the load-transfer measurements were performed to examine the axial resistant behavior of the piles. A comprehensive field/laboratory testing program on weathered rock at the field test sites was also performed to describe the in situ rock mass conditions quantitatively. And then, the effect of rock mass condition on the load transfer mechanism was investigated. The side shear resistance of the pile in moderately weathered rock reached to yielding point at a few millimeter displacements, and after that, the rate of resistance increment dramatically decreased. However, that in the highly /completely weathered rock did not show the obvious yielding point, and gradually increased showing the hyperbolic pattern until with the relatively high displacement (>10 mm). The end bearing-displacement curves showed linear increase at least until with the base displacement of approximately 10 mm, regardless rock mass conditions.

• Economic and Environmental Geology
• /
• v.29 no.5
• /
• pp.639-660
• /
• 1996

The lowest formation of the Cretaceous Gyeongsang Supergroup, the Nakdong Formation, unconformably overlies the gneiss complex basement in Hadong, Gyeongsangnam-do and Gwangyang, Chullanam-do. The Nakdong Formation of the study area is 500-600 m thick and occurs as a belt shape. Based upon lithology, sedimentary structure, and bedding geometry the formation consists of three conglomerate facies (Gd, Gn, Gic), five sandstone facies (Sh-n, Sh-i, Sp, Sr, Sm), and four mudstone facies (Mf, Mfn, Mc, Mv). Sandstone facies are the most prominent in the study area. The twelve facies can be grouped into five facies associations. The depositional settings are elucidated from analyses of 12 facies and five facies associations of the formation. The lower part of the Nakdong Formation was deposited in alluvial plain, and the middle and upper parts were in a riverine system. The lithologies of the Nakdong Formation of the Gyeongsang Basin have been considered to consist of generally conglomerates and pebbly sandstones that were accumulated in alluvial fans. But the common lithology of the study area is sandstone which was formed in lower part of alluvial fan or fluvial setting. It is supposed that the coarser sedimentary sequence distributed west to the study area should be eroded out after deposition and early uplift, and the finer sandstone sequence in the east remains behind. The mineral composition of sandstones and the clast composition of conglomerates indicate that the Nakdong Formation was derived mainly from the metamorphic source rocks. Some reworked intraclasts were also supplied from the intrabasinal sedimentary layers. Paleocurrent data collected from cross-beddings, ripple marks, asymmetric sand dune suggest that most sediments were transported from north to south during the Nakdong Formation time.

• Economic and Environmental Geology
• /
• v.30 no.2
• /
• pp.163-174
• /
• 1997

Precambrian metapelites and metapsammites of the Jinan-Osu area (so-called Seologri and Yongamsan Formation) consist of black slate, phyllite, mica schist, quartzite and rarely calc schist. They are intruded by Sunkagsan granite gneiss, Foliated granodiorite, Amphibolite, Sunchang foliated granite and Namwon granite. Mylonite texture, crenulation cleavage and minor shear zone are common. The meta-sedimentary rocks include various rock-fragments xenoliths in size (up to 3 cm) and rock-type. They have various porphyroblastic spots in size (up to 1 cm) and their mineral composition is different. The xenoliths are schists, granite and quartzite, which are rectangular or lens form and recrystallized muscovite, chlorite and quartz. Spots are andalusite and biotite aggregates extensively replaced by chlorite. The metamorphic terrain is divided into three zones of progressive metamorphism on the basis of mineral assemblage. They are chlorite zone, chloite-biotite zone and andalusite-biotite zone ascending order, from west to east approximately. Isograd reactions are phengitic muscovite + chlorite = less phengitic muscovite + biotite + quartz + $H_2O$ and muscovite + chlorite + quartz = andalusite + biotite + $H_2O$ between the chlorite zone and chlorite-biotite zone, and between the chloritebiotite zone and andalusite-biotite zone, respectively. Sample B6 (exposed near the Obong-ri) includes staurolites and greenish biotites, that is different in mineral assemblage and chemical composition from the meta-sedimentary rocks. Sample A12 (exposed near the Shinam-ri) has greenish white spots (up to 1 cm in diameter) mainly composed of Kfeldspar, quartz and sillimanite replaced by muscovite.

• Tunnel and Underground Space
• /
• v.23 no.5
• /
• pp.401-412
• /
• 2013

Multi-stage shear test has been performed using joint specimens of gneiss, granite and shale to investigate the influence of micro-scale asperity change on the shear strength of joint plane. For each shear test asperity degradation characteristics of joint specimens of different joint surface strength have been analyzed by utilizing the optimum asperity parameter which can reflect the sequential asperity degradation. Elevation of joint surface profile has been measured and both the changes of asperity parameters and micro-scale asperity distribution have been investigated. Two distinctive variation modes of cohesion and friction angle have been delineated and major cause of shear strength parameter change has been analyzed by considering the micro-scale asperity angle change resulting from the abrasion, fracturing and regeneration of micro-scale asperities. Effects of micro-scale asperity variation on the joint shear strength have been also investigated.

• Journal of the Korean earth science society
• /
• v.23 no.1
• /
• pp.87-96
• /
• 2002

Aeromagnetic and gravity data were analyzed to delineate the subsurface structure of the Yeongdong basin and its related fault movement in the Okcheon fold belt. The aeromagnetic data of the total intensity (KIGAM, 1983) were reduced to the pole and three dimensional inverse modeling, which considers topography of the survey area in the modeling process, were carried out. The apparent susceptibility map obtained by three dimensional magnetic inversion, as well as the observed aeromagnetic anomaly itself, show clearly the gross structural trend of the Yeongdong basin in the direction on between $N30^{\circ}E$ and $N45^{\circ}E$. Gravity survey was carried out along the profile, of which the length is about 18.2 km across the basin. Maximum relative Bouguer anomaly is about 7 mgals. Both forward and inverse modeling were also carried out for gravity analysis. The magnetic and gravity results show that the Yeongdong basin is developed by the force which had created the NE-SW trending the magnetic anomalies. The susceptibility contrast around Yeongdong fault is apparent, and the southeastern boundary of the basin is clearly defined. The basement depth of the basin appears to be about 1.1 km beneath the sea level, and the width of the basin is estimated to be 7 km based on the simultaneous analysis of gravity and magnetic profiles. There exists an unconformity between the sedimentary rocks and the gneiss at the southeastern boundary, which is the Yeongdong fault, and granodiorite is intruded at the northwestern boundary of the basin. Our results of gravity and magnetic data analysis support that the Yeongdong basin is a pull-apart basin formed by the left-stepping sinistral strike-slip fault, which formed the Okcheon fold belt.

• Journal of the Mineralogical Society of Korea
• /
• v.19 no.2 s.48
• /
• pp.99-109
• /
• 2006

Igneous rocks occurring in the northwesern part of Keumsan area, Chungcheongnam-do were studied petrogeochemically. The geology of this area is composed mainly of the Precambrian biotite gneiss, age-unknown Ogchon supergroup, Jurassic biotite granite, and Cretaceous volcanic rocks, pink feldspar granite and quartz porphyry. The biotite granite is gradually changes to leucocratic nature by going from center to periphery of the rock mass. It shows variation, with distance from the center, in chemical components: $SiO_2,\;Na_2O\;and\;K_2O$ increase, whereas $Fe_2O_3,\;CaO,\;P_2O_5,\;MgO,\;and\;TiO_2$ decrease. Based on geochemical data, the biotite granite and quartz porphyry belong to subalkaline series and I-type. They show calc-alkaline differentiation trend. The biotite granite shows little negative Eu-anomaly pattern, whereas quartz porphyry show marked negative Eu-anomaly pattern, indicating that quartz porphyry was evolved further, when compared with biotite granite.

• Journal of the Mineralogical Society of Korea
• /
• v.25 no.4
• /
• pp.295-304
• /
• 2012

Ilmenite mine was developed in the anorthosites which intruded Precambrian Jirisan gneiss complex in Wolheongri, Okjong-myeon, Hadong. Ti-ore bodies are confined to the intercumulated type anorthosites, where REE-bearing allanite occurred as veins. The chemistry of allanites shows relatively low in CaO (11.02~12.81 wt%), but high in ${\Sigma}R_2O_3$ (R = Ce, La, Nd) (17.21~21.58 wt%), respectively. Abnormally high radioactive detection ascribes to the presence of small particles of thorium mineral known as thorite ($ThSiO_4$). Thorite shows 65~72.78 wt% ($ThO_2$) and 5.49~12.78 wt% ($UO_2$) in composition. The radioactive prospecting could be a strong tool to find REE-bearing allanite which is closely associated with Ti-ore deposits.

• Journal of the Korean association of regional geographers
• /
• v.8 no.4
• /
• pp.468-479
• /
• 2002

This study attempts to characterize Taebaek mountainous region as a natural unit, relating to morphoclimatic milieu and landform development patterns of the mountains of each lithologic type. In the case of granitic mountains of Nothern parts of this region, the slopes presents more or less steep or irregular profile because of abundant microforms of exposed bedrocks and blocks. The development of such landscape is essentially due to differential weathering, associated with difference of joint density. In the case of gneissic mountains, the slopes are well regularized straight steep ones, due not only to generalized superficial weathering but also to massmovement of weathered materials. In the Middle parts of this region, especially in Taegwallyong area, with frequent alternations both of freezing-thawing and of snow accumulation-melting, the roles played by cryo-nival processes proved to be important in weathering of granite as well as in morpho-pedogenesis. In this area, weathered mantle, developed by cryogenic activity under humid condition of nival environment, covered almost all over the slopes. Although Southern parts of this region consist of limestone, on the mountainous volume, distribution of Karst forms are limited while predominate none karst forms such as cockpit type peaks, V-shaped type valleys dissecting steep slopes covered with thin deposits in thickness containing rock debris.