• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10b
• /
• pp.307-308
• /
• 2003

Improved wettability and dyeability of Polypropylene(PP) fabrics were obtained using glow discharge plasma by grafting nitrogen-containing active groups on the surface. Few studies of glow discharge plasma on PP fabrics exist. The objective of this study was to give a fabric a good affinity for water. (omitted)

• Korean Journal of Materials Research
• /
• v.12 no.11
• /
• pp.870-874
• /
• 2002

$Mg_2$$SiO_4$: Dy, Tb pellets were made by using a sintering process, including pressing and heat treatment. In the present study, the optimum parameters of the sintering for the $Mg_2$$SiO_4$: Dy, Tb pellets obtained such as the pressing pressure, the sintering temperature and the sintering time were in terms of thermoluminescence. Experimental results showed that the main peak of the glow curve for $Mg_2$$SiO_4$: Dy, Tb thermoluminescence dosimeter was clearly correlated with the energy of the UV and with the grain size. The intensity of the TL glow curve increased and its main peak position shifted to lower temperature with increasing UV irradiation time.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.5
• /
• pp.54-61
• /
• 2001

It is reported that during the cold starting, especially in gasoline engine, the engine response and the effect of HC emission can be improved by prompting atomization and reducing the quantity of fuel adhered to the range of injector tip, inlet port, and inlet valve. The purposes of this study are to promote atomization of fuel before air-fuel mixture in the inlet port. In order to achieve its goal, the glow plug is to evaluate the feasibility of for the early fuel evaporator and the spray behavior characteristics of gasoline, injected on the surface of glow plug with room temperature(2$0^{\circ}C$) and high temperature(25$0^{\circ}C$) is to examine. Particle motion analysis system(PMAS) was used to measure the SMD and the dropsize distribution of impinging spray and free spray. The results of this experiment, evaporation rate of impinging spray was higher than that of free spray, and the higher evaporation rate win, the smaller peak dropsize was. Especially, during early spray SMD of impinging spray was still smaller than that of fee spray.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1382-1384
• /
• 1995

In order to study the structure of RF glow discharge driven at 13.56MHz in argon, the discharge voltage, current and phase shift between them will be measured over a wide range of discharge parameters(gas pressure between 1mTorr and 50mTorr with discharge power between 20mW and 200W). In this paper, the dc glow discharge characteristics and plasma parameters of both FTS and CPMS systems are studied experimentally. It is found that for CPMS system discharge is stablized under wider ranges of magnetic field and pressure than for FTS system. The plasma density and electron temperature of the plasma for these two systems are in the range of $10^{10}{\sim}7{\times}10^{11}[cm^{-3}]$ and $3.5{\sim}6.5$[eV], respectively.

• Journal of radiological science and technology
• /
• v.22 no.1
• /
• pp.55-60
• /
• 1999

In this study, the highly sensitive $CaSO_4:Tb$ glass capsule type TLDs are fabricated and their trap parameters are determined. The optimum conditions of fabricating of $CaSO_4:Tb$ phosphor was obtained to be in impurity concentration of Tb 1.0 mol% and sintering of $600^{\circ}C$, 2 hr. The glow curve of $CaSO_4:Tb$ consists of three glow peaks and these peaks are isolated by thermal bleaching method. Activation energy of the three glow peaks measured by the initial rise, the peak shape and the heating rate method are 0.70, 0.87, and 1.03 eV. The frequency factors are $1.76{\times}10^9,\;1.74{\times}10^9$, and $9.77{\times}10^8\;s^{-1}$, and the kinetic orders are 1.12, 1.46, and 1.34, respectively. The isolated glow peaks are fitted by least square method and optimum temperature range of the main peak for radiation dosimetry is $230{\sim}295^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.911-914
• /
• 1992

We have investigated the micro-discharge in plasma display panel using 2 dimensional 2 fluid MHD equations. Plasma display utilizes the physical phenomena of the normal glow or abnormal glow and is considered to be able to provide the largest display area among various flat panel. 2 fluid, 2 dimensional Magneto-Hydro-Dynamic equations are applied to Computational field of 100${\times}$800${\mu}m^2$. Time varing glows and after-glows were investigated for 11 $\mu$sec. We obtained the distribution of the microscopic variables such as the density, temperature, velocity of Ne+Ar0.1% gas plasma. During the first 6$\mu$ sec, glow discharge dued to DC pulse was investigated. Time varing phenomena of after-glow was also investigated during the last 5 $\mu$set. From results, it was found that the driving efficiency of a DC Plasma Display Panel could be improved when the diffusion of ions and electrons are controlled by the pulses applied to the auxiliary anode.

• Korean Journal of Food Science and Technology
• /
• v.42 no.6
• /
• pp.648-652
• /
• 2010

This study was performed to investigate PSL and TL characteristics for the detection of different ratios of gamma-irradiated turmeric. It was possible to determine PSL and TL of 1- and 10-kGy irradiated turmeric. The TL ratios ($TL_1/TL_2$) of non-irradiated samples were lower than 0.001, while those of irradiated samples were higher than 0.355. In the PSL results, blended samples containing irradiated ingredients showed intermediate values for a 1% blending rate. Furthermore, TL analysis of blended samples seems to offer a promising method for irradiation identification by TL glow curve form and temperature range. The 1- and 10-kGy irradiated samples were able to be detected above a 4% blending rate. However, the TL ratio appeared as a threshold value below 0.1 for irradiated samples. Overall, TL analysis identified 4% blended samples containing gamma-irradiated turmeric.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.10
• /
• pp.902-907
• /
• 2003

In this paper, the ITO thin film, which is considered as one of the most currently used material for the high performance transparent conducting films for the PDP cell, was made in a parallel-plate, capacitively coupled DC magnetron sputtering system. Some electrical and optical properties of ITO films were investigated and discussed on the basis of glow discharge characteristics. The optimized thin film fabricating conditions of Ar gas pressure and substrate temperature were derived from the Paschen curve and glow discharge characteristics. The maximum transmittance of 89.61 % in the visible region and optical band gap of 3.89 eV and resistivity of 1.67${\times}$10$\^$-3/ $\Omega$-cm were obtained under the conditions of 300 C of substrate temperature and 10∼15 mtorr of pressure, which corresponds nearly to that of Paschen minimum.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.2
• /
• pp.406-414
• /
• 2010

A novel polyacrylamide grafted hydrous ferric oxide adsorbent composite has been synthesized by using glow discharge electrolysis plasma. To optimize the synthesis conditions, the following parameters were examined in detail: applied power, discharge time, post polymerization temperature, post polymerization time, amount of crosslinking agent and hydrous ferric oxide gel added and so on. The adsorbent was characterized by Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS). The removal percentage of the adsorbent in Pb(II) solution was examined and the data obtained showed that the adsorbent composite has a high capacity for lead ion. For the use in wastewater treatment, the thermodynamic and kinetic of Pb(II)-capture were also studied. Results indicated that the adsorption reaction was a spontaneous and an endothermic process, and it seems to be obeyed a pseudo-secondorder rate model. Moreover, the adsorption isotherm of Pb(II)-capture is following the Langmuir and Freundlich isotherm models.

• Korean Journal of Food Science and Technology
• /
• v.30 no.4
• /
• pp.759-766
• /
• 1998

It was determined whether thermoluminescence (TL) technique is a potential method to detect post-irradiation of dry soup base mix for instant noodle and its ingredients. The ingredients or the mixtures were irradiated, from which minerals were isolated using sodium polytungstate solution. Their TL signals (1st glow TL intensity/2nd glow TL intensity reirradiated at 48.6 Gy) were measured. The TL signals in temperature ranges of $229{\sim}295^{\circ}C$ and $229{\sim}361^{\circ}C$ showed larger differences between unirradiated and irradiated samples compared to other ranges. The average TL signals for unirradiated garlic powder, ginger powder, black pepper powder, onion powder, red pepper powder, and sesame seeds were below 0.2, while those for onion powder, red pepper powder, and sesame seeds irradiated at 10 kGy were over 20 in the two temperature ranges. The average TL signals for unirradiated soup mixture were 0.08 and 0.1, respectively, in the two temperature ranges, while those for the mixtures containing 10 kGy-irradiated onion powder, red pepper powder, and sesame seeds individually or in combination were over 7. The average TL signals for the mixtures irradiated 1, 5, and 10 kGy were over 10.