• Korean Chemical Engineering Research
• /
• v.46 no.5
• /
• pp.886-891
• /
• 2008

Contact glow discharge electrolysis(CGDE) is an unconventional electrolysis where plasma is sustained by D.C. glow discharge between an electrode and the surface of electrolyte surrounding it at high voltage. In this study, the behavior of CGDE in NaCl solution and the depolymerization of fucoidan by CGDE were investigated. After onset of CGDE, increase of voltage enhanced Glow discharge which resulted in low current density and low temperature in NaCl electrolyte. From the variation of molecular weight of fucoidan with the reaction time, it was demonstrated that the degradation of fucoidan followed a first-order rate law. Molecular weight of fucoidan treated with CGDE was about 40 times lower compared to initial fucoidan without content decrease of sulfate and fucos.

• Textile Coloration and Finishing
• /
• v.11 no.2
• /
• pp.27-37
• /
• 1999

Polypropylene(PP) films were treated with plasma glow discharge to produce peroxy radicals on the surfaces. The peroxy radicals formed on the PP film surfaces were subsequently used for the graft polymerization of acrylic acid and acrylamide in an aqueous solution by heating, respectively. Introduction of acrylic acid and acrylamide on the PP film could be confirmed by the observation of carbonyl and primary amine absorptions based on carboxylic acid and amide, respectively. And introduction of functional group could be confirmed by weight analysis and ESCA. The water contact angle(90$^{\circ}$) of PP film was constant, irrespective of elapsed time, while plasma-treated and functional monomer-grafted PP films were slowly increased with elapsed time, showing the rearrangement of surface polar groups in air condition. The water contact angle$(90^\circ)$ of PP film was decreased by the plasma treatment$(56^\circ)$ and further decreased by the grafting of acrylic acid$(34^\circ)$ and acrylamide$(37^\circ)$, indicating increased hydrophilicity of the modified surfaces. The water contact angle of plasma-treated PP film increased a little as time elapsing. The half-life periods of surface voltage on acrylic acid-(31sec) and acrylamide-grafted PP(42sec) were significantly decreased when compared to those on PP(950sec) and plasma-treated PP film(241sec). In the experiments using acid, basic and disperse dyes, absorbance and $\Delta{E}$ values of functional monomer-grafted PP films were significantly increased than that of oxygen plasma-treated one.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.1 no.4
• /
• pp.197-201
• /
• 2001

The influence of argon, oxygen, and nitrogen admixtures on the dissociation of $Cl_2$ molecules in a glow discharge low-temperature plasma under the constant pressure conditions was investigated. For $Cl_2/Ar$ and $Cl_2/O_2$mixtures, the concentration of chlorine atoms was observed to be a practically constant at argon or oxygen concentrations up to 50%. This invariability is a most pro bably explained by relative increase in rate of $Cl_2$ direct electron impact dissociation due to the changes in electrophysical parameters of plasma such as EEDF, electron drift rate and mean energy. For all the considered mixtures, the contribution of stepwise dissociation involving active species from gas additives (metastable atoms and molecules, vibrationally excited molecules) was found to be negligible.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.99-102
• /
• 2005

Plasma surface coating is applied to the wood powder to improve its bonding and dispersion with the polypropylene(PP). Some mechanical test results and visual inspection indicates the good compatibility between the wood powder and the PP, and relatively good interfacial adhesion between wood powder and PP matrix was seen. Also, this method is considered as a non-toxic process as compared to other direct chemical method.

• 전기의세계
• /
• v.27 no.3
• /
• pp.36-42
• /
• 1978

It has been investigates that electric characteristics of plasma electron beam in N$_{2}$, H$_{2}$ and Ar gas jars under various gas pressures during electron beams are formed. The results are as follows: 1)Electron beam is formed in the region of positive resistance on the characteristic curve. This phenomenon is identical in N$_{2}$, H$_{2}$ and Ar gases. 2)But in Ar gas, electron beam is formed at relatively lower gas pressure than in H$_{2}$ and N$_{2}$. 3)In pure gas either N$_{2}$, H$_{2}$ and N$_{2}$ the lower the gas pressure, the higher the voltage drop for the same electron beam current. 4)The region in which electron beam is formed is limited at a given pressure. 5)Beyond the limit mentioned above, it becomes glow discharge state and the current increases radically. 6)At a given gas pressure, electron beam voltage, that is, electrical power input increases with gap length.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.6
• /
• pp.307-314
• /
• 2021

Diamond-like carbon (DLC) is difficult to achieve sufficient adhesion because of weak bonding between DLC film and the substrate. The purpose of this study is to improve the adhesion between substrate and DLC film. DLC film was deposited on AISI H13 using linear ion source. To improve adhesion, the substrate was treated by dual post plasma nitriding. In order to define the mechanism of the improvement in adhesive strength, the gradient layer between substrate and DLC film was analyzed by Glow Discharge Spectrometer (GDS) and Scanning Electron Microscope (SEM). The microstructure of the DLC film was analyzed using a micro Raman spectrometer. Mechanical properties were measured by nano-indentation, micro vickers hardness tester and tribology tester. The characteristic of adhesion was observed by scratch test. The adhesion of the DLC film was enhanced by active screen plasma nitriding layer.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.221-222
• /
• 2006

This paper describes a Plasma Assisted Debinding and Sintering (PADS) equipment, which has been designed to process Metal Injection Molded (MIM) components. The use of a hybrid system combining a glow discharge with a conventional heating system makes debinding and sintering of MIM components, in the same heating cycle, a feasible industrial process. Characteristics as density, carbon content and mechanical properties are similar to traditionally processed MIM materials. The reduction of energy and gas consumption and shorter lead-times are economic advantages of PADS system. The clean environment of PADS is also an ecological advantage.

• Fashion & Textile Research Journal
• /
• v.16 no.3
• /
• pp.456-461
• /
• 2014

The objective of this study is to give PP(polypropylene) fabric a good affinity for water. Oxygen plasma was treated to PP fabrics in a commercial glow discharge reactor with different RF power, discharge pressure, and reaction time. The PP fiber surfaces were characterized by the measurement of contact angle and ESCA. A JEOL scanning electron microscope was used to observe the surface morphology of fibers. The spontaneous water uptake amount of PP fabrics was determined by the demand wettability test. To determine the effect of aging on the surface properties of $O_2$ plasma treated PP, all the above measurements of the samples were carried out after 1, 7, 30, 60, and 150 days. The results are as follows. The PP fiber surfaces treated by $O_2$ plasma treatment have a chemical composition that consisted of various oxygen containing polar groups. Consequently, the contact angles of the treated PP fibers decreased, which improved the water uptake rate of PP fabrics. Surface roughness of the treated PP affected the fabric wettabiity as well. Wettability of the treated PP decreased and leveled off with aging. The $O_2$ plasma treatment is a simple and effective method to increase the water uptake rate of PP fabrics.

• Applied Chemistry for Engineering
• /
• v.22 no.3
• /
• pp.261-265
• /
• 2011

The sterilization effects of atmospheric pressure plasma with the mixture of argon and oxygen were analyzed. The plasma reactor with the shape of dielectric barrier discharge produced the uniform distribution of glow discharge and generated ozone gas effectively according to the various process parameters. The sterilization for E. coli was affected by power, oxygen ratio in the mixture gas, treatment time and distance between reactor and sample. The concentration of ozone was a major source for the sterilization of E. coli, which was enhanced by the increase of power and oxygen ratio. In this study, the effect of atmospheric pressure plasma treatment for the sterilization was confirmed and its result can deliver the atmospheric pressure plasma treatment as the novel sterilization method instead of conventional methods.

• Analytical Science and Technology
• /
• v.12 no.4
• /
• pp.299-305
• /
• 1999

The electrolyte cathode atomic glow discharge (ELCAD) is a new plasma source for direct determination of trace heavy metals in drinking and waste water. ELCAD has been successfully developed for on-line monitoring of heavy metals, however, shows difficulty to measure mercury. In this study, ELCAD has been modified to apply the atomic absorption spectrometry (AAS) for the direct determination of trace elements of mercury in flowing water.The fundamental characteristics of this new types of plasma source have been investigated and found that the pH of the solution, discharge voltage, and current are most important factors.The absorbance of 1.0 ppm Hg standard solution increases as pH of the solution increases from pH 1.0 to 3.0.However, % RSD of the absorbance also increases as the pH of solution increasesdue to plasma unstability.The detection limits of the standard solution of pH 1.5 and pH 3.0 are about 40 ppb and 10 ppb level, respectively.