• Resources Recycling
• /
• v.31 no.5
• /
• pp.42-51
• /
• 2022

Aggregate resources in Korea are expected to run out owing to an increase in development demand and construction investment. Recycled concrete aggregates (RCA), extracted from waste concrete, have a lower quality than natural aggregates. However, RCA can produce concrete similar in quality to the normal concrete by aggregate pretreatment, use of admixtures, and quality control. RCA are most suitable for use in precast concrete products such as sidewalk blocks and revetment blocks. Herein, the feasibility of producing revetment blocks using recycled aggregate concrete (RAC), similar in quality to normal concrete, was analyzed. The amount of RCA was varied, and moderate high early strength cement and steam curing were used to produce the concrete test blocks. In the block test, the load resistance characteristics of the blocks were evaluated to determine optimal RAC and glass fiber reinforced polymer (GFRP) rebar compositions. Thus, the variable that reduced the cement content was determined at the same level as that of natural aggregate concrete by the control of steam curing. In the concrete block test, although this depends on the reinforcement ratio, the RAC block exhibited the same or better performance than a normal concrete block. Therefore, the low quality of RCA in RAC is no longer a problem when concrete mixing and curing are controlled and appropriate reinforcement is used.

• Applied Chemistry for Engineering
• /
• v.33 no.1
• /
• pp.50-57
• /
• 2022

Ti-In-Zn-O (TIZO)/Ag/TIZO multilayer transparent electrodes were prepared on glass substrates at room temperature using RF/DC magnetron sputtering. Obtained multilayer structure comprising TIZO/Ag/TIZO (10 nm/10 nm/40 nm) with the total thickness of 60 nm showed a transmittance of 86.5% at 650 nm and a sheet resistance of 8.1 Ω/□. The multilayer films were expected to be applicable for use in energy-saving smart window based on polymer-dispersed liquid crystal (PDLC) because of their transmittance properties to effectively block infrared rays (heat rays). We investigated the effects of the content ratio of prepolymer, the thickness of the PDLC coating layer, and the ultraviolet (UV) light intensity on electro-optical properties, and the surface morphology of polyester acrylate-based PDLC systems using new TIZO/Ag/TIZO transparent conducting electrodes. A PDLC cell with a thickness of 15 ㎛ PDLC layer photocured at an UV intensity of 1.5 mW/cm² exhibited good driving voltage, favorable on-state transmittance, and excellent off-haze. The LC droplets formed on the surface of the polymer matrix of the PDLC composite had a size range of 1 to 3 ㎛ capable of efficiently scattering incident light. Also, the PDLC-based smart window manufactured using TIZO/Ag/TIZO multi-layered transparent electrodes in this study exhibited a light brown, which will have an advantage in terms of aesthetics.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1251-1251
• /
• 2001

The routine analysis of milk chemical components is of major importance both for the management of animals in dairy farms and for quality control in dairy industries. NIRS technology is an analytical technique which greatly simplifies this routine. One of the most critical aspects in NIRS analysis of milk is sample preparation and analysis modes which should be fast and straightforward. An important difficulty when obtaining NIR spectra of milk is the high water content (80 to 90%) of this product, since water absorbs most of the infrared radiation, and, therefore, limits the accuracy of calibrating for other constituents. To avoid this problem, the DESIR system was set up. Other ways of radiation-sample interaction adapted for liquids or semi-liquids exist, which are practically instantaneous and with limited or null necessity of sample preparation: Transmission and Folded Transmission or Transflectance. The objective of the present work is to compare the precision and accuracy of milk calibration equations in two analysis modes: Reflectance (dry milk) and Folded Transmission (liquid milk). A FOSS-NIR Systems 6500 I spectrophotometer (400-2500 nm) provided with a spinning module was used. Two NIR spectroscopic methods for milk analysis were compared: a) folded transmission: liquid milk samples in a 0.1 pathlength sample cell (ref. IH-0345) and b) reflectance: dried milk samples in glass fibre filters placed in a standard ring cell. A set of 101 milk samples was used to develop the calibration equations, for the two NIR analysis modes, to predict casein, protein, fat and dry matter contents, and 48 milk samples to predict Somatic Cell Count (SCC). The calibrations obtained for protein, fat and dry matter have an excellent quantitative prediction power, since they present $r^2$ values higher than 0.9. The $r^2$ values are slightly lower for casein and SCC (0.88 and 0.89 respectively), but they still are sufficiently high. The accuracy of casein, protein and SCC equations is not affected by the analysis modes, since their ETVC values are very similar in reflectance and folded transmission (0.19% vs 0.21%; 0.16% vs 0.19% and 55.57% vs 53.11% respectively), Lower SECV values were obtained for the prediction of fat and dry matter with the folded transmission equations (0.14% and 0.25% respectively) compared to the results with the reflectance ones (0.43% and 0.34% respectively). In terms of accuracy and speed of analytical response, NIRS analysis of liquid milk is recommended (folded transmission), since the drying procedure takes 24 hours. However, both analysis modes offer satisfactory results.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.2
• /
• pp.120-129
• /
• 2023

Marine structures are subject to damage not only from sea salt but also from the adhesion of marine microorganisms and suspended particles, which cause additional damages. In order to prevent this, periodic coating is employed in the case of vessels to maintain the necessary performance. However, it is true that periodic coating is difficult for concrete or steel support structures, and there is a risk of marine environmental pollution. In this study, authors developed an anti-fouling coating agent using eco-friendly materials that possess hydrophilic cellulose nanofibers and AKD(alkyl ketene dimer). To achieve a homogeneous mixture, the content of cellulose nanofibers was fixed at 1 %, and AKD, distilled water, and waste glass were mixed using a digital mixer and homogenizer. The contact angle of the prepared coated surface was observed to be over 130°, indicating sufficient performance even in a water droplet flow test with a 15° slope, suggesting self-cleaning capability. Furthermore, through the analysis of viscosity characteristics at different temperatures, it was confirmed that the application is feasible at room temperature. Microstructure analysis also verified that the coating agent is uniformly applied to the concrete surface.

• Journal of the Korean earth science society
• /
• v.44 no.3
• /
• pp.210-221
• /
• 2023

The purpose of this study is to evaluate the content knowledge and problem solving process used by pre-service earth science teachers while discriminating faults on geological maps. For this, we collected and evaluated data on fixation duration and gaze plot, while pre-service earth science teachers (N=12) solved the problem on faults interpretation using an eye tracker (Tobii Pro Glass 2 model). The results were as follows. First, most of the pre-service earth science teachers know the concepts of the normal and reverse fault but they do not know the procedural knowledge essential for fault interpretation on geological maps. Second, the pre-service earth science teachers did not draw a geological cross-sectional map to interpret the fault on the geological map and interpreted the fault based on two-dimensional information collected from the geological map rather than three-dimensional information. Therefore, it is essential to improve the teaching and learning environment so that pre-service earth science teachers who will become earth science teachers in the future can learn procedural knowledge essential to comprehend natural phenomena including understanding natural phenomena. The results of this study can substantially help organize a new earth science curriculum or develop materials on teachers' education in the future.

• Journal of Bio-Environment Control
• /
• v.20 no.3
• /
• pp.182-188
• /
• 2011

This research was conducted to evaluate the effect of supplemental light-emitting diode (LED) light on growth characteristics and phytochemical content of pepper (Capsicum annuum L.) seedling using LED blue (470 nm, B), red (660 nm, R), blue + red (BR), far red (740 nm, FR) and UV-B (300 nm) light treatment, and without artificial light. Photon flux of LED light was 49, 16, 40, 5.0 and $0.82{\mu}mol\;m^{-2}s^{-1}$ for B, R, BR, FR, and UV-B light, respectively, during experiment. Supplemental LED light duration was $16hr\;day^{-1}$ and UV-B light duration was 10 min. per day after sunset up to 15 days (12 days after germination) of plants age. In our research, growth characteristics and phytochemical content of pepper seedlings were greatly influenced by supplemental LED light compare to control treatment. Red light increased the number of leaves, number of nodes, leaf width and plant fresh weight by 34%, 27%, 50% and 40%, respectively. Blue light increased the leaf length by 13%, and stem length and length of inter node were increased by 17% and 34%, respectively under grown far red light. After 15 days of light treatments phytochemical concentrations of pepper plants were significantly changed. Blue light enhanced the total anthocyanin and chlorophyll concentration by 6 times and 2 times, respectively. Red light increased the total phenolic compound at least two folds meanwhile far red light reduced the ascorbic acid and antioxidant activity 31% and 66%, respectively compared to control treatment.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.16 no.1
• /
• pp.8-11
• /
• 2012

Purpose : Among quality control items, the radiochemical impurity must be below 10% of total radioactivity. In this regard, as the recently commercialized automatic synthesis module produces a large amount of 18F-FDG, radiolysis of radiopharmaceuticals is very likely to occur. Thus, this study compared the changes in radiochemical purity regarding radiolysis of $^{18}F$-FDG according to automatic synthesis module. Materials and methods : Cyclotron (PETtrace, GE Healthcare) was used to produce $^{18}F$ and automatic synthesis module (FASTlab, Tracerlab MX, GE Healthcare) was used to achieve synthesis into FDG. For radiochemical purity, Radio-TLC Scanner (AR 2000, Bioscan), GC (Gas Chromatograph, Agilent 7890A) was used to measure the content of ethanol included in $^{18}F$-FDG. Glass board applied with silica gel ($1{\times}10cm$) was used for stationary phase while a mixed liquid formed of acetonitrile and water (ratio 19:1) was used for mobile phase. High-concentration and low-concentration $^{18}F$-FDG were produced in each synthesis module and the radiochemical purity was measured every 2 hours. Results : The purity in low-concentration (below 2.59 GBq/mL) was measured as 99.26%, 98.69%, 98.25%, 98.09% in Tracerlab MX and as 99.09%, 97.83%, 96.89%, 96.62% in FASTlab according to 0, 2, 4, 6 hours changes, respectively. The purity in high-concentration (above 3.7 GBq/mL) was measured as 99.54%, 96.08%, 93.77%, 92.54% in Tracerlab MX and as 99.53%, 95.65%, 92.39%, 89.82% in FASTlab according to 0, 2, 4, 6 hours changes, respectively. Also, ethanol was not detected in GC of $^{18}F$-FDG produced in FASTlab, while 100~300 ppm ethanol was detected in Tracerlab MX. Conclusion : Whereas the change of radiochemical purity was only 3% in low-concentration $^{18}F$-FDG, the change was rapidly increased to 10% in high-concentration. Also, higher radiolysis were observed in $^{18}F$-FDG produced in FASTlab than Tracerlab MX. This is because ethanol is included in the synthesis stage of Tracerlab MX but not in the synthesis stage of FASTlab. Thus, radiolysis is influenced by radioactivity concentration than the inclusion of ethanol, which is the radioprotector. Therefore, after producing high-concentration $^{18}F$-FDG, the content must be diluted through saline to lower concentration.

• Food Science and Preservation
• /
• v.21 no.2
• /
• pp.187-192
• /
• 2014

This study was conducted to develop a salad dressing using jujube (Zizyphus jujuba Miller) puree and to evaluate the processing and quality characteristics of the salad dressing containing various amounts (0, 10, 20, 30, 40, and 50%) of jujube puree. Jujube puree was prepared by crushing peeled, deseeded and steamed fruit flesh. The dressing ingredients (jujube flesh puree, soy sauce, vinegar, oligosaccharide, olive oil, and water) were mixed, homogenized, and packaged in glass bottles. The quality characteristics (color property, total titratable acidity, soluble solids, viscosity, phenolic compound content, antioxidant activity, and sensory acceptability) of the dressing were analyzed. The lightness ($L^*$) and redness ($a^*$) of the dressing tended to increase as the amount of the jujube puree increased whereas the hue angle ($h^{\circ}$) decreased. The total titratable acidity, soluble solids, viscosity, phenolic compound content, and antioxidant activity of the dressing increased with the addition of more jujube puree. The sensory acceptability (color, smell, taste, texture, and overall acceptability) were significantly higher in the dressing added with 30% added jujube puree than in the other samples. The results show that jujube flesh puree (approximately 30%) can be utilized as an additive for preparing a dressing with simultaneously high antioxidant activity and acceptability.

• Korean Journal of Environmental Biology
• /
• v.26 no.4
• /
• pp.385-391
• /
• 2008

In Korea, Quercus acutissima distributed in good condition with high nutrients and moisture content, but Quercus variabilis in dry soil or rock habitate. In order to understand this ecological distribution of Q. acutissima and Q. variabilis, we cultivated the seedlings of two oak species treated with light, soil moisture and nutrient gradients each four level, from May to October in glass house. Then we measured the ecological niche breadth and niche overlap of the two species, and analyzed the relationship of competition using cluster analysis and PCA ordination. Ecological niche breadths of Q. acutissima under moisture and nutrient treatments were slightly wider than those under light one. Among 14 characters measured, 6 characters related with length items were wider in all the environmental treatments, but 8 characters connected with weight terms narrower in light treatment. Ecological niche breadths of Q. variabilis under moisture and nutrient treatment were wider than those of light one. Ecological niche of Q. acutissima was wider than those of Q. variabilis in all the environmental treatments. Ecological overlap between two species was higher with a range of 0.87$\sim$0.92, especially higher in soil moisture factor. These results means that Q. acutissima is more competitive than Q. variabilis, especially in soil moisture condition. Two species were ordinated with distinct group based on 9 characters. From these results, it can be explained that what Q. variabilis distributed in bad soil condition is due to the escape strategy, because of its low competitive ability to Q. acutissima in natural communities.

• Korean Journal of Food Science and Technology
• /
• v.10 no.2
• /
• pp.112-118
• /
• 1978

Four domestic frying oils (soybean, corn, rapeseed and rice bran oil) were studied on their changing properties according to thermal oxidation by means of chemical analysis of their compositions and measurements of various physical and chemical properties. The content of linoleic acid which is an essential unsaturated fatty acid and the total amount of unsaturated fatty acids were highest in soybean oil (53.2% and 80.3% respectively) among the unheated frying oils and the degree of its thermal degradation was lowest during the continuous heating period for 48 hours at $180^{\circ}C$. However in general, the contents of unsaturated fatty acids were sharply decreased by thermal oxidation whereas the saturated fatty acid contents ranging 10-17% were not changed considerably, which largely agreed with the results of iodine value measurements. The free acid and peroxide values were also lowest in soybean oil (0.09 and 5.6 respectively) among the unheated oils whereas an anomalously high free acid value was observed in rapeseed oil (54.8) which was packed in unleveled glass bottles. Such a high value is probably ascribed to the photo-catalyzed oxidation during storage. The viscosity measurements have shown similar values before heating, but after thermal oxidation for 32 hours the rapeseed and rice bran oils became too thick to measure viscosity by capillary flow method with heavy darkening in color.