• 한국정밀공학회지
• /
• 제27권7호
• /
• pp.28-35
• /
• 2010

In the display industry, COG bonding method is being applied to production of LCD panels that are used for mobile phones and monitors, and is one of the mounting methods optimized to compete with the trend of ultra small, ultra thin and low cost of display. In COG bonding process, electrical characteristics such as contact resistance, insulation property, etc and mechanical characteristics such as bonding strength, etc depend on properties of conductive particles and epoxy resin along with ACF materials used for COG by manufacturers. As the properties of such materials have close relation to optimization of bonding conditions such as temperature, pressure, time, etc in COG bonding process, it is requested to carry out an in-depth study on characteristics of COG bonding, based on which development of bonding process equipment shall be processed. In this study were analyzed the characteristics of COG bonding process, performed the analysis and reliability evaluation on electrical and mechanical characteristics of COG bonding using ACF to find optimum bonding conditions for ACF, and performed the experiment on bonding characteristics regarding fine pitch to understand the affection on finer pitch in COG bonding. It was found that it is difficult to find optimum conditions because it is more difficult to perform alignment as the pitch becomes finer, but only if alignment has been made, it becomes similar to optimum conditions in general COG bonding regardless of pitch intervals.

• Korea-Australia Rheology Journal
• /
• 제19권3호
• /
• pp.125-131
• /
• 2007

Biodegradable polymeric blends are expected to be widely used by industry due to their environmental friendliness and comparable mechanical and thermal properties. Poly (lactic acid) (PLA) and poly (butylene succinate) (PBS) are such biodegradable polymers which aim to replace commodity polymers in future applications. Since cost and brittleness of PLA is quite high, it is not economically feasible to use it alone for day to day use as a packaging material without blending. In this study, blends of PLA and PBS with various compositions were prepared by using a laboratory-scale twin-screw extruder at $180^{\circ}C$. Morphological, thermal, rheological and mechanical properties were investigated on the samples obtained by compression molding to explore suitability of these compositions for packaging applications. Morphology of the blends was investigated by scanning electron microscopy (SEM). Morphology showed a clear phase difference trend depending on blend composition. Modulated differential scanning calorimetry (MDSC) thermograms of the blends indicated that the glass transition temperature ($T_g$) of PLA did not change much with the addition of PBS, but analysis showed that for PLA/PBS blend of up to 80/20 composition there is partial miscibility between the two polymers. The tensile strength and modulus were measured by the Instron Universal Testing Machine. Tensile strength, modulus and percentage (%) elongation at break of the blends decreased with PBS content. However, tensile strength and modulus values of PLA/PBS blend for up to 80/20 composition nearly follow the mixing rule. Rheological results also show miscibility between the two polymers for PBS composition less than 20% by weight. PBS reduced the brittleness of PLA, thus making it a contender to replace plastics for packaging applications. This work found a partial miscibility between PBS and PLA by investigating thermal, mechanical and morphological properties.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.933-937
• /
• 2002

The fiber reinforced composite material is widely used in the multi-industrial field where the weight reduction of the infrastructure is demanded because of their high specific modulus and specific strength. Pressure vessels using this composite material in comparison with conventional metal vessels can be applied in the field where lightweight and the high pressure are demanded from the defense and aerospace industry to rocket motor case due to the merits which are energy cutdown the weight reduction and decrease of explosive damage preceding to the sudden explosion which is generated by the pressure leakage condition). In this paper, for nonlinear finite element analysis of E-glass/epoxy filament winding composite pressure vessel receiving an internal pressure, the standard interpretation model is developed by using the ANSYS, general commercial software, which is verified as the accuracy and useful characteristic of the solution based on Auto LISP and ANSYS APDL. Both the preprocessor for doing exclusive analysis of filament winding composite pressure vessel and postprocessor that simplifies result of analysis have been developed to help the design engineers.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.459-459
• /
• 2012

Recently, the discharge of global warming gases in dry etching process of TFT-LCD display industry is a serious issue because perfluorocarbon compound (PFC) gas causes global warming effects. PFCs including CF4, C2F6, C3F8, CHF3, NF3 and SF6 are widely used as etching and cleaning gases. In particular, the SF6 gas is chemically stable compounds. However, these gases have large global warming potential (GWP100 = 24,900) and lifetime (3,200). In this work, we chose C3F6O gas which has a very low GWP (GWP100 = <100) and lifetime (< 1) as a replacement gas. This study investigated the effects of the gas flow ratio of C3F6O/O2 and process pressure in dual-frequency capacitively coupled plasma (CCP) etcher on global warming effects. Also, we compared global warming effects of C3F6O gas with those of SF6 gas during dry etching of a patterned positive type photo-resist/silicon nitride/glass substrate. The etch rate measurements and emission of by-products were analyzed by scanning electron Microscopy (SEM; HITACI, S-3500H) and Fourier transform infrared spectroscopy (FT-IR; MIDAC, I2000), respectively. Calculation of MMTCE (million metric ton carbon equivalents) based on the emitted by-products were performed during etching by controlling various process parameters. The evaluation procedure and results will be discussed in detail.

• 열처리공학회지
• /
• 제24권1호
• /
• pp.31-36
• /
• 2011

$TiO_2$ films were deposited on a glass substrate with RF magnetron sputtering and then surface of $TiO_2$ films were electron beam irradiated in a vacuum condition to investigate the effect of electron bombardment on the thin film crystallization, surface roughness and gas sensitivity for hydrogen. $TiO_2$ films that electron beam irradiated at 450eV were amorphous phase, while the films irradiated at 900 eV show the anatase (101) diffraction peak in XRD pattern. AFM measurements show that the roughness is depend on the electron irradiation energy. As increase the hydrogen gas concentration and operation temperature, the gas sensitivity of $TiO_2$ and $TiO_2$/ZnO films is increased proportionally and $TiO_2$ films that electron beam irradiated at 900 eV show the higher sensitivity than the films were irradiated at 450eV. From the XRD pattern and AFM observation, it is supposed that the crystallization and rough surface promote the hydrogen gas sensitivity of $TiO_2$ films.

• 한국구조물진단유지관리공학회 논문집
• /
• 제9권3호
• /
• pp.120-128
• /
• 2005

콘크리트용 혼화재료로 고로슬래그미분말은 경제적, 환경적 이점뿐만 아니라, 고강도, 내해수성, 내화학성과 같은 성능개선의 효과도 있다. 고로슬래그미분말이 콘크리트용 재료로서 아주 유용한 자원임에도 불구하고, 초기 강도의 저하로 인한 거푸집의 해체 및 순환의 문제로 공사기간이 지연되어 공사비의 증가 등의 단점이 있다. 따라서 본 연구에서는 고로슬래그미분말 혼합 모르타르의 초기 강도의 증진을 위하여, 다양한 알칼리 자극제를 혼합 사용하여, 모르타르의 유동성 및 압축강도 특성을 평가하였다. 또한 알칼리 자극제의 혼합에 따른 수화 반응 성상을 알아보기 위하여, XRD 분석, 미소수화열 및 $Ca(OH)_2$를 정량하였다. 실험결과 유동성과 응결시간에 대한 단점을 고로슬래그미분말로 보완하고, 적당한 알칼리 자극제의 선택과 첨가량을 조절하여 사용한다면, 고로슬래그미분말을 콘크리트에 사용하여도 초기 강도 저하 없이 사용가능할 것으로 판단된다.

• 한국식품과학회지
• /
• 제14권1호
• /
• pp.43-48
• /
• 1982

말쥐치 및 도루묵을 보다 효과적으로 이용하기 위하여, 축육과 유사한 텍스쳐를 가진 어육단백질농축물 저장 중의 품질 안정성 및 이용방안에 대하여 검토하였다. 제품은 함기포장하여 상온에 저장하여도 복수성, TBA값 및 갈변도 등에 큰 변화없이 90일간 품질이 안정하게 유지되었다. 햄버어그 및 튀김어단을 만들때 쇠고기 대신에 축육과 유사한 텍스쳐를 가진 어육단백질농축물을 50%까지 섞어도 맛, 냄새 및 텍스쳐 등에 별다른 손색이 없었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.936-936
• /
• 2006

Bulk amorphous materials have been intensively studied to apply for various advanced industry fields due to their high mechanical, chemical and electrical properties. These materials have been produced by several techniques such as mechanical alloying, melt spinning and gas atomization, etc. Among them, the atomization is the most potential technique for commercialization due to high cooling rate during solidification of the melt and mass productivity. However, the amorphous powders still have some limitations because of their low ductility and toughness. Therefore, intensive efforts have to be carried out to increase the ductility and toughness. In this study, the Ni-based amorphous powder was produced by the gas atomization process. And in order to increase the ductile toughness, ductile Cu phase was coated on the Ni amorphous powder by spray drying process. The characteristics of the as-synthesis powders have been examined and briefly mentioned. The master alloy with $Ni_{57}Zr_{20}Ti_{16}Si_2Sn_3$ was prepared by vacuum induction melting furnace with graphite crucible and mold. The atomization was conducted at $1450^{\circ}C$ under the vacuum of $10^{-2}$ torr. The gas pressure during atomization was varied from 35 to 50 bars. After making the Ni amorphous powders, the spray drying was processed to produce the Cu -coated Ni amorphous composite powder. The amorphous powder and Cu nitrate solution were mixed together with a small amount of binder and then it was sprayed at temperature of $130^{\circ}C$ and rotating speed of 15,000 R.P.M.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.41-44
• /
• 2008

Fiber Reinforced Plymers (FRPs)는 기존 보수 보강재료에 비해 높은 강도, 내부식성, 절연성등 뛰어난 역학적 특성으로 인하여, 최근들어 기존 구조물의 보수 및 보강에 FRP를 이용한 외부부착 공법 이 활발하게 사용되어지고 있다. 현재 국내 외적으로 FRP 재료를 이용한 외부부착 공법이 적용된 철근 콘크리트보에 관한 연구는 활발히 진행되고 있으나 시간 의존적 거동에 관한 연구는 아직 미흡한 실정이다. 이에 대하여 본 연구에서는 무보강 RC보, Carbon Fiber Reinforced Plymers(CFRPs) 와 Glass Fiber Reinforced Plymers (GFRPs)로 보강된 철근콘크리트보 실험체를 제작하여 약 300일간 25KN의 지속하중을 받은 FRP 보강보의 시간경과에 따른 처짐, 변형률 그리고 온도 변화의 영향을 관찰하였다. 실험 결과 CFRP로 보강된 실험체는 GFRP로 보강된 실험체보다 시간의존적 거동에 있어 더 우수한 보강성능이 있음을 확인할 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제27권2호
• /
• pp.85-90
• /
• 2014

Ag paste has been used in the front electrode of the Si-solar cell. It is composed by Ag powder, glass frit, binder, solvent and dispersant. The role of the binder and the solvent is to make a flow and a printing property. However, it was not enough to report the printing properties with the variation of binder in the controled viscosity. In this study, we selected 3 kinds of typical binder which were used as binder for the paste in the industry, such as Ethyl cellulose, Hydroxypropyl cellulose and Acrylic. Ag pastes using these were prepared, controled viscosity and printed on the SiNx coated Si wafer. In the 'A paste' used Acrylic binder, printed hight was highest and 'H paste' used Hydroxypropyl cellulose binder was lowest. Because 'H paste' was high viscosity due to the molecular weight, the solvent was added in the paste to control the viscosity. Therefore, the content of solid was lower in 'H paste'. The relative pattern width which is related to the spreading of paste was the best in the case of 'H paste' and 'EH paste' at $30^{\circ}C$. It is thought that the optimization of the relative pattern width is possible for a paste by the controling shear thinning phenomenon. In the case of 'A paste', though printing hight was best, the pattern width was dependant on the temperature.