• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.176-183
• /
• 2001

It is difficult to find out the kinematic characteristics of a vehicle suspension without the usage of CAE software. The application of CAE software into suspension kinematics and dynamics yields the more precise knowledge on the chassis design. In this study, the influence of the suspension geometry on the handling performances of a large-sized bus is investigated using the DADS software. The front and rear suspension of a large-sized bus are a rigid axle suspension with the four control links. The elastokinematic analysis is performed to evaluate the roll characteristics of the front and rear suspension. The elastokinematic responses are evaluated in terms of the roll center height and roll steer for various geometric parameters. The roll center height is mainly dependent on the vertical displacement of a panhard rod and the vertical displacements of lower control links affect the roll steer of a rear suspension. The parameter study with the change of rear suspension geometry is conducted to investigate the vehicle handling performances. This parameter study shows that the vertical displacement and orientation of a panhard rod influence the handling performances of a large-sized bus significantly.

• Journal of Welding and Joining
• /
• 제29권4호
• /
• pp.41-47
• /
• 2011

GMA welding process is a production process to improve productivity for the provision of higher welding quality of material. These includes numerous process variables that could affect welding quality, productivity and cost savings. Recently, the welding part of construction equipment had frequent failure of major components in the welding part of each subsidiary material due to shock which is very poor according to the welding part. Therefore, the implementation of sound welding procedure is the most decisive factor for the reliability of construction machinery. The data generated through experiments conducted in this study has validated its effectiveness for the optimization of bead geometry and process variables is presented. The criteria to control the process parameters, to achieve a good bead geometry. This study has developed mathematical models and algorithms to predict or control the bead geometry in GMA fillet welding process.

• 한국통신학회:학술대회논문집
• /
• 한국통신학회 1984년도 추계학술발표회논문집
• /
• pp.15-18
• /
• 1984

The majority - logic decoding algorithm for Geometry code is more simply imlemented than the known decoding algorithm for BCH codes. Thus, the moderate code word, Geometry codes provide rather effective error control. The purpose of this paper is to investigate the Reed - Muller code and to design the encoder and decoder circuit and to find the performance for (15, 11) Reed - muller code. Experimental results show that the system has not only single error - correcting ability but also good performance.

• 한국환경복원기술학회지
• /
• 제15권2호
• /
• pp.19-29
• /
• 2012

Numerous studies suggested that fish assemblage structure reflects the status of stream ecosystems. The status of streams integrity, including various trophic levels, water quality and habitat degradation, can be assessed by fish assemblages. In this study, we investigated the relationships between fish assemblages and streamline geometry of streams. Previous studies suggested that geomorphologic parameter can be a critical factor of permeability between adjacent two systems. From a landscape ecological perspective, edges may partially control the flow rate of energy between two adjacent systems. Thus, the Streamline geometry can be a geomorphologic parameter that exhibits the integrity of stream. We selected the Nakdong river for study areas, which is one of major rivers and the longest (525 km) River in South Korea. We used the revised IBI representing overall ecological characteristics of Korean fish assemblages and eight sub-assessment criteria of IBI, collected from 82 sampling sites in the Nakdong River. For calculating the Streamline geometry, we measured fractal dimension index that generally used in biology, ecology and landscape ecology. We used the digital land-use/land-cover map and generated a 1-km buffer for each sampling site and refined the shape of the Streamlines. Pearson correlation analyses were performed between Streamline geometry and IBI and sub-assessment criteria of IBI. The results show that IBI and eight sub-assessments of fish are significantly correlated with geometry of Streamline. The fractal dimension of Streamline geometry were related with IBI (r = 0.48) and six sub-assessments of IBI, including total number of native fish and native species, the number of riffle benthic species, sensitive species, tolerant species and native insectivore. Especially, the number of tolerant species(r = -0.52) and native insectivore(r = 0.52) show strong correlation with geometry of Streamline. These results indicate that lower Streamline geometry can result in poor fish assemblages, while higher geometry of Streamline can enhance fish assemblages by potentially supplying insects and better habitat conditions. We expect the results of our study to be useful for stream restoration and management. However, we see the necessity of study investigating the mechanisms how Streamline geometry affect fish assemblages.

• 콘크리트학회논문집
• /
• 제19권2호
• /
• pp.233-239
• /
• 2007

본 연구의 주요 목적은 시멘트 복합 재료의 소성 수축 균열 제어에 폐 PET병으로부터 만들어진 재생 PET 섬유의 효과를 평가하는 것이다. PET은 플라스틱 재료라 알려진 재료로 음료수 병 등에 다양하게 적용되어 왔다. 그렇지만 폐 PET 병은 사용 후에 환경적 측면에서 큰 문제점으로 부각되고 있다. 따라서 폐 PET 병을 재활용하는 방법에 대한 연구는 환경 및 경제적 측면에서 중요하게 되었다. 폐 PET 병을 재활용하는 방법 중 시멘트 복합 재료의 보강 섬유로 사용하는 방법은 효과적인 방법 중에 하나이다. 본 연구에서는 시멘트 복합 재료의 소성 수축 균열에 재생 PET 섬유의 형상 및 길이의 효과를 얇은 슬래브 실험을 통해서 조사하였다. 실험 계획은 섬유의 형상, 길이 및 혼입률의 영향을 이해하기 위하여 수행하였다. 재생 PET섬유의 형상은 straight, crimped및 embossed type의 3가지 형상을 포함하며, 각 3가지 섬유형상 마다 3가지 수준의 섬유 혼입률 및 2가지 종류의 섬유 길이에 대해서 조사하였다. 실험 결과 재생 PET섬유는 시멘트 복합 재료의 소성 수축 균열에 효과적이었다. 섬유의 길이의 관점에서 길이가 긴 섬유는 섬유의 형상이 동일할 때 섬유체적비가 적을 때 효과적이며, 섬유체적비가 증가하면 길이가 짧은 섬유가 더욱더 효과적이었다. 또한 embossed type의 섬유는 적은 섬유 혼입률에서 다른 형상의 섬유보다 소성 수축 균열 제어 효과가 우수하였으며, 높은 섬유 혼입률에서는 straight type의 섬유가 다른 형상의 섬유보다 시멘트 복합 재료의 소성 수축 균열 제어에 가장 효과적이었다.

• 한국콘텐츠학회논문지
• /
• 제11권1호
• /
• pp.236-244
• /
• 2011

성능이 저하된 IVR 장치의 지속적 사용은 환자 및 시술자의 방사선 피폭을 증가시킬 뿐 아니라, 잘못된 영상정보를 제공함으로써 환자에게 심각한 영향을 끼칠 수 있다. 따라서 이번 연구에서는 IVR장치의 성능평가를 위한 적절한 시험방법 및 검사기준을 마련하고자 하였다. IVR장치의 국내현황 및 규격을 조사하였으며, 표준팬텀을 이용하여 국내 IVR장치의 성능을 현장 측정함으로써, 국내 실정에 맞는 적절한 IVR 장치의 화질 및 성능평가 기준을 설정하였다. 장치의 기본적 성능에 관한 검사를 위해 관전압시험, 관전류 시험, 반가층 시험을 실시하며, NEMA stndard XR-21 Phantom을 표준팬텀으로 사용하여 화질 및 선량 평가를 하도록 하였다. 표준팬텀을 이용한 검사항목은 image-field geometry, spatial resolution, low-contrast iodine detectability, wire resolution, phantom entrance dose이다. 또한 매일, 매주, 1개월, 3개월, 6개월 및 1년 주기의 평가항목을 설정하였다. 장치의 성능기준은 진단용방사선안전관리 규정을 준용하여 kVp시험은 평균오차 ${\pm}10%$, mA시험은 평균오차 ${\pm}15%$, 반가층시험은 80kVp에서 최소 2.3mmAl으로 설정하였다. 표준팬텀의 검사기준은 image-field geometry에서 최소 acceptable이 나와야 하며, spatial resolution은 Image Intensifier 나 detector 크기기준으로 34-40cm은 0.8 lp/mm, 28-33cm은 1.0lp/mm, 22-27cm은 1.2 lp/mm이상이 나와야 한다. low contrast iodine detectability는 최소농도 200mg/cc 이상 보여야 하며, phantom entrance dose는 10R/min을 초과해서는 안 된다. Wire resolution은 정지 상태에서 최소 0.012인치까지 보여야 하며, 움직일 때 최소 0.022인치까지 보여야 한다.

• 대한조선학회논문집
• /
• 제57권2호
• /
• pp.96-103
• /
• 2020

The new geometric disturbance is proposed to control the flow around the bluff body. The new geometry is characterized by the variable pitch which is applied on the Helically Elliptic Twisted (HET) cylinder. The performance of the HTE geometry as a biomimetic passive flow control was confirmed by Jung and Yoon (2014). The Large Eddy Simulation (LES) is used for the evaluation of the flow control performance of the Variable Pitch HTE (VPHTE) cylinder at Reynolds number (Re) of 3000 corresponding to the subcritical regime. The circular and HTE cylinders are also considered to compare the performance of the VPHTE cylinder at the same Re. The VPHTE cylinder gives the smallest values of the force coefficients than the circular and HTE cylinders. The drag and lift coefficients of the VPHTE cylinder are about 15.2% and 94.0% lower than those of the circular cylinder, respectively. Especially, the VPHTE cylinder achieves about 2.3% and 30.0% reduction of the drag coefficient and the root mean square of the lift coefficient than the HTE cylinder, respectively. Furthermore, The VPHTE cylinder forms more elongated and stabilized separated shear layer than the circular cylinder, which supports the reduction of the force coefficients.

• 한국정밀공학회지
• /
• 제14권4호
• /
• pp.56-63
• /
• 1997

Sealing of lubricant-air mixture in the high performance machining center is one of most the important characteristics to carry out enhanced lubrication. High speed spindle requires non-contact type of sealing mechanism. Evaluating an optimum seal design to minimize leakage is concerned in the aspect of flow control. Effect of geometry and leakage path are evaluated according to variation of sealing geometry. Velocity, pressure, turbulence intensity of profile is calculated to find more efficient geometry and variables. This offers a methodological way of enhancement seal design for high speed spindle. The working fluid is regarded as two phases that are mixed flow of oil phase and air phase. It is more reasonable to simulate an oil jet or oil mist type high speed spindle lubrication. Turbulence and compressible flow model are used to evaluate a flow characteristic. This paper considers a design effect of sealing capability of non- contact type seals for high speed spindle and analyzes leakage characteristics to minimize a leakage 7 on the same sealing area.

• 한국정밀공학회지
• /
• 제20권7호
• /
• pp.217-226
• /
• 2003

Twin screw extruders are the heart of the polymer processing industry. They are used at some stage in nearly all polymer processing operations. This paper is concerned with the basic elements of the extruder design. The proper design of the geometry of the extruder screw is of crucial importance to the proper functioning of the extruder. If the material transport instabilities occur as a result of improper screw geometry, even the most sophisticated computerized control system cannot solve the problem. For this purpose, a characteristic design on the screw flights shape of the closely intermeshing co-rotating twin screw extruder. This paper presents design parameters of double flighted screw and triple flighted screw elements, and characteristics of various screw channel area versus screw diameter ratio, K value, in the barrel of screw extruder.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.906-909
• /
• 2005

In this study, the dynamic flying characteristics of the worn head sliders are investigated theoretically due to the change in head geometry caused by head and disk contact. The film shapes can be approximated as taper- truncated cycloidal-flat film. Two-dimensional time dependent modified Reynolds equation included molecular slip effect are formulated with neglected the roughness effect. The motion of head slider was assumed to have two degree of freedom in this work. Finite difference approximation with Newton Raphson iterative technique and the fourth order Runge-Kutta method were implemented to obtain the transient response of the slider head with various change in head geometry numerically and compared with the transient response of the IBM3380 type head slider. The simulation results show the film shape has affects significantly on the static and dynamic characteristic of slider head in magnetic storage systems.