• Nuclear Engineering and Technology
• /
• v.52 no.6
• /
• pp.1271-1276
• /
• 2020

The geometrical efficiency of a source-to-detector configuration is considered to be necessary in the calculation of the full energy peak efficiency, especially for NaI(Tl) and HPGe gamma-ray spectroscopy detectors. The geometrical efficiency depends on the solid angle subtended by the radioactive sources and the detector surfaces. The present work is basically concerned to establish a new mathematical approach for calculating the solid angle and geometrical efficiency, based on conversion of the geometrical solid angle of a non-axial radioactive point source with respect to a circular surface of the detector to a new equivalent geometry. The equivalent geometry consists of an axial radioactive point source with respect to an arbitrary elliptical surface that lies between the radioactive point source and the circular surface of the detector. This expression was extended to include coaxial radioactive circular disk source. The results were compared with a number of published data to explain how significant this work is in the efficiency calibration procedure for the γ-ray detection systems, especially in case of using isotropic radiating γ-ray sources in the form of point and disk shapes.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.6
• /
• pp.22-31
• /
• 2009

Canting is the optical alignment of mirror facets of heliostat such that the heliostat could focus the energy as a unit concentrator. Canting could improve the optical performance of heliostat and thus improves the efficiency of heliostat and ultimately improves the efficiency of the solar thermal power plant. This study discusses the effect of mirror canting, especially off-axis canting, used to compensate the sun tracking error caused by the heliostat geometrical errors. We first show that the canting could compensate the sun tracking error caused by the heliostat geometrical errors. Then we show that the proper canting time could exist, depending on the heliostat location. Finally we show how much the sun tracking performance could be improved by canting, by providing RMS sun tracking error. The limitation and caution of using canting to improve the sun tracking performance are also discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.05a
• /
• pp.172-176
• /
• 1995

Schemes to trap weakly absorbed light into the cell have played an important role in improving the efficiency of both amorphous and crystlline silicon solar cells. One class of scheme relies on randomizing the direction of light within the cell by use of Lambertian(diffuse)surfaces. A second class of scheme relies on the use fo well defined geometrical features to control the direction of light wihin the cell, Widly used geometrical features in crystalline silicon solar cells are the square based pyramids and V-shaped grooves formed in (100) orientated surfaces by intersecting(III) crystallographic planes exposed by anisotropic etching. 18.5% conversion efficiency of Buried Contact Solar Cell with pyramidally textured surface has been achieved. 18.5% efficiency of silicon solar cell is one the highest record in the world The efficieny of cell without textured surface was 16.6%, When adapting textured surface to the Cell, the efficiency has been improved over 12%.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.7
• /
• pp.1-8
• /
• 2012

In this paper, we improved the light extraction efficiency by structural change of LEDs on conventional LEDs. We simulated the LEDs light emission as functions of LED side wall angle, various refractive indices the geometrical structures and analyzed the condition improved the light efficiency. We present the results of experimerns and simulations for light output power from LEDs for various refractive indices and the geometrical structures of the LED encapsulants. When the side wall angle range was from 40[$^{\circ}$] to 30[$^{\circ}$], the LED emission increased. LED side wall angle onto LED using the simulation system with a fine tuning of the structure of the LEDs side wall angle is fabricated. Additionally, we changed the side wall angle of LED package with spherical structure and flat structure. The result of spherical structure ray tracting is higher compared with flat structure about 14[%].

• Journal of the Korean Solar Energy Society
• /
• v.29 no.3
• /
• pp.1-11
• /
• 2009

Heliostat sun tracking accuracy could be the most important requirement in solar thermal power plant, since it determines the overall efficiency of power plant. This study presents the effect of geometrical errors on the heliostat sun tracking performance. The geometrical errors considered here are the mirror canting error, encoder reference error, heliostat position error. pivot offset and tilt error, gear backlash and mass unbalanced effect error. We first investigate the effect of each individual geometrical error on the sun tracking accuracy. Then, the sun tracking error caused by the combination of individual geometrical error is computed and analyzed. The results obtained using the solar ray tracing technique shows that the sun tracking error due to the geometrical error is varying almost randomly. It also shows that the mirror canting error is the most significant error source, while the encoder reference error and gear backlash are second and the third dominant source of errors.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.2
• /
• pp.39-46
• /
• 2009

Heliostat, as a mirror system tracking the sun's movement, is the most important subsystem determining the efficiency of solar thermal power plant. Thus the accurate sun tracking performance under the various hazardous operating condition, is required. This study presents a methodology of development of the solar ray tracing technique and the application of it in the analysis of sun tracking error due to the heliostat geometrical errors. The geometrical errors considered here are the azimuth axis tilting error and the elevation axis tilting error. We first analyze the geometry of solar ray reflected from the heliostat. Then the point on the receiver, where the solar ray reflected from the heliostat is landed, is computed and compared with the original intended point, which represents the sun tracking error. The result obtained shows that the effect of geometrical error on the sun tracking performance is varying with time(season) and the heliostat location. It also shows that the heliostat located near the solar tower has larger sun tracking error than that of the heliostat located farther.

• The KIPS Transactions:PartB
• /
• v.9B no.4
• /
• pp.491-500
• /
• 2002

In this paper, we propose a real-time face detection and recognition system by using skin color informations, geometrical feature vectors of face, and facial angle informations from color face image. The proposed algorithm improved face region extraction efficiency by using skin color informations on the HSI color coordinate and face edge information. And also, it improved face recognition efficiency by using geometrical feature vectors of face and facial angles from the extracted face region image. In the experiment, the proposed algorithm shows more improved recognition efficiency as well as face region extraction efficiency than conventional methods.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.30B no.10
• /
• pp.13-26
• /
• 1993

Motion picture algorithms are realized on the multiprocessor system presented in the Study I. For the most efficient processing of the algorithms, pipelining and geometrical parallel processing methods are employed, and processing time, communication load and efficiency of each algorithm are compared. The performance of the implemented system is compared and analysed with reference to MPEG coding algorithm. Theoretical calculations and experimental results both shows that geometrical partitioning is a more suitable parallel processing algorithm for moving picture coding having the advantage of easy algorithm modification and expansion, and the overall efficiency is higher than pipelining.

• Advances in aircraft and spacecraft science
• /
• v.2 no.1
• /
• pp.1-16
• /
• 2015

In this paper, geometrical and mechanical approaches are proposed for the simulation of the draping of woven fabric onto complex parts. The geometrical discrete approach allows to define the ply shapes and fibres orientation in order to optimize the composite structural properties and the continuum meso-structural mechanical approach allows to take into account the mechanical properties of fibres and resin and the various dominating mode of deformation of woven fabrics during the forming process. Some numerical simulations of forming process are proposed and compared with the experimental results in order to demonstrate the efficiency of our approaches.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1303-1308
• /
• 2008

This paper presents effects of impeller geometrical parameters on the performance of a centrifugal pump impeller. The effects of meridional parameters and vane plane development parameters on the performance of the impeller were numerically studied using a commercial CFD code and DOE(design of experiments) software. Geometrical parameters in a method of meridional view and vane plane development were selected and defined to generate the 3D impeller shape. The response variables are defined in a total head and efficiency curve with flow rate. The influences of selected design variables on the various objective functions were examined as a result of the calculation using 2k factorial.