• 산업경영시스템학회지
• /
• 제28권3호
• /
• pp.156-165
• /
• 2005

A new heuristic algorithm for the heterogeneous single container loading problem is proposed in this paper, This algorithm fills empty spaces with the homogeneous load-blocks of identically oriented boxes and splits residual space into three sub spaces starting with an empty container. An initial loading pattern is built by applying this approach recursively until all boxes are exhausted or no empty spaces are left. In order to generate alternative loading patterns, the load-blocks of pattern determining spaces are replaced with the alternatives that were generated on determining the load-blocks. An improvement algorithm compares these alternatives with the initial pattern to find improved one. Numerical experiments with 715 test cases show the good performance of this new algorithm, above all for problems with strongly heterogeneous boxes.

• 대한조선학회논문집
• /
• 제36권3호
• /
• pp.29-40
• /
• 1999

캐비테이션이 발생하지 않는 프로펠러의 정상 및 비정상 하중에 의해 음장에 유기되는 소음을 지배하는 음파 방정식에 대한 주파수 영역에서의 수치 해석법을 정립하였다. 본 연구를 통하여 음압 스펙트럼에서 날개 통과 진동수 배수의 소음만이 발생한다는 것을 보였으며, 이때 적용되는 파수는 반류의 불균일성에 기인하는 조화성분과 프로펠러의 회전에 의해 발생되는 Doppler 효과가 고려되도록 표현되어야 함을 보였다. 특정 전진속도에서 하중이 없도록 설계된 날개수가 2인 모형 프로펠러에 대한 이론적 추정과 실험결과를 비교함으로써, 정상상태인 경우 날개 두께 효과가 매우 중요하나, 비정상상태에서는 날개하중의 변화에 의한 소음의 영향이 커서 정상상태에 비하여 두께효과가 비교적 적게 기여함을 알 수 있었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.189-195
• /
• 2003

This paper represents an identification procedure for leading mechanism of a car A/V system which is composed of a DC motor and a set of plastic gears. In addition, we studied dominant noise source of rattle noise generated by external forced vibration as a car drives. we made a dynamometer to produce stationary operation on loading mechanism of A/V system because noise generated by actual loading mechanism is non-stationary signal. operating the dynamometer setup at various motor speeds, sound pressure spectra are measured and the results are analyzed. its dominant noise source is also identified by using a sound Intensity technique. we made use of multi-dimensional spectral analysis to rind a dominant rattle noise. this method is so useful to eliminate coherence between vibration sources and helps us obtain coherent output spectrum of individual vibration source which make a rattle noise.

• 대한산업공학회지
• /
• 제21권1호
• /
• pp.119-135
• /
• 1995

We consider problems of tool loading and scheduling in a flexible manufacturing system (FMS) in which tool transportation constitutes the major portion of material flows. In this type of FMSs, parts are initially assigned to machines and released to the machines according to input sequencing rules. Operations for the parts released to the machines are performed by tools initially loaded onto the machines or provided by an automatic tool transport robot when needed. For an efficient operation of such systems, therefore, we may have to consider loading and scheduling problems for tools in addition to those for parts. In this paper, we consider three problems, part loading, tool loading, and tool scheduling problems with the overall objective of minimizing the makespan. The part loading problem is solved by a method similar to that for the bin packing problem and then a heuristic based on the frequency of tool usage is applied for tool loading. Also suggested are part input sequencing and tool scheduling rules. To show the effectiveness of the overall algorithm suggested here, we compare it with an existing algorithm through a series of computational tests on randomly generated test problems.

• 대한기계학회논문집A
• /
• 제24권8호
• /
• pp.2074-2082
• /
• 2000

In this study, to investigate and to predict the crack growth behavior under variable amplitude loading, crack growth tests are conducted on 7075-T6 aluminum alloy. The loading wave forms are generated by normal random number generator. All wave forms have same average and RMS(root mean square) value, but different standard deviation, which is to vary the maximum load in each wave. The modified Forman's equation is used as crack growth equation. Using the retardation coefficient D defined in previous study, the load interaction effect is considered. The variability in crack growth process is described by the random variable Z which was obtained from crack growth tests under constant amplitude loading in previous work. From these, a statistical model is developed. The curves predicted by the proposed model well describe the crack growth behavior under variable amplitude loading and agree with experimental data. In addition, this model well predicts the variability in crack growth process under variable amplitude loading.

• 동력기계공학회지
• /
• 제8권4호
• /
• pp.11-16
• /
• 2004

In this study, to investigate the effects of omitting low-amplitude cycles from a flight-simulation loading, crack growth tests were conducted on 2124-T851 aluminum alloy specimens. Three test spectra were generated by omitting small load ranges as counted by the rain-flow count method. The crack growth test results were compared with the data obtained from the flight-simulation loading. The experimental results show that the ranges equal to or smaller than 5% of the maximum load do not contribute to crack growth behavior because these are below the initial stress intensity factor range. Omitting these from the flight-simulation loading, test time can be reduced by 54%. However, in the case of omitting the load ranges below 15% of the maximum load, crack growth rates decreased, and crack growth curve deviated from the crack growth data under the flight-simulation loading because loading cycles above fatigue fracture toughness were omitted.

• 한국정밀공학회지
• /
• 제20권11호
• /
• pp.188-193
• /
• 2003

To predict changes in biomechanical parameters such as intradiscal pressure, and the shock absorbing mechanism in the spinal motion segment under different impact duration/loading rates, a three dimensional L3/L4 motion segment finite element model was modified to incorporate the poroelastic properties of the motion segment. The results were analyzed under variable impact duration for normal and degenerated discs. For short impact duration and a given maximum compressive force, relatively high cancellous pore pressure was generated as compared with a case of long impact duration, although the amount of impulse was increased. In contrast relatively constant pore pressure was generated in the nucleus. Disc degeneration increased pore pressure in the disc and decreased pore pressure in the cancellous core, which is more vulnerable to compressive fracture compared with intact case.

• Wind and Structures
• /
• 제15권2호
• /
• pp.177-188
• /
• 2012

The meteorological events that cause most strong winds in Brazil are extra-tropical cyclones, downbursts and tornadoes. However, one hurricane formed off the coastline of southern Brazil in 2005, a tropical storm formed in 2010 and there are predictions that others may form again. Events such as those described in the paper and which have occurred before 1987, generate data for the wind map presented in the Brazilian wind loading code NBR-6123. This wind map presents the reference wind speeds based on 3-second gust wind speed at 10 m height in open terrain, with 50-year return period, varying from 30 m/s (north half of country) to 50 m/s (extreme south). There is not a separation of the type of climatological event which generated each registered velocity. Therefore, a thunderstorm (TS), an extra-tropical pressure system (EPS) or even a tropical cyclone (TC) are treated the same and its resulting velocities absorbed without differentiation. Since the flow fields generated by each type of meteorological event may be distinct, the indiscriminate combination of the highest wind velocities with aerodynamic coefficients from boundary layer wind tunnels may lead to erroneous loading in buildings.

• Structural Engineering and Mechanics
• /
• 제30권6호
• /
• pp.665-678
• /
• 2008

The beams components subjected to the loading such as axial, bending and cyclic thermal loads were studied in this research. The used constitutive equations are those of elasto-plasticity coupled to ductile and/or creep damage. The nonlinear kinematic hardening behavior was considered in elastoplasticity modeling. The unified damage law proposed for ductile failure and fatigue by the author of Sermage et al. (2000) and Kachanov's creep damage model applied to cyclic creep and low cycle fatigue of beams. Based on the results of the analysis, the shakedown limit loads were determined through the calculation of the residual strains developed in the beam analysis. The iterative technique determines the shakedown limit load in an iterative manner by performing a series of full coupled elastic-plastic and continuum damage cyclic loading modeling. The maximum load carrying capacity of the beam can withstand, were determined and imposed on the Bree's interaction diagram. Comparison between the shakedown diagrams generated by or without creep and/or ductile damage for the loading patterns was presented.

• 한국기계가공학회지
• /
• 제12권4호
• /
• pp.3-9
• /
• 2013

Falling related injuries are categorized as the most serious and common medical problems experienced by the elderly. Hip joint fracture, one of the most serious consequences of falling in the elderly, occurs in only about 1% of falling. In this study, according to the loading conditions, the analysis is the behavior of the femur. The CT images using the commercial program "Mimics" the bones of three-dimensional CAD data generated, and we will analyze the results of finite element analysis. The boundary conditions on the basis of existing research has been simplified. In this paper, the whole femur was assumed to be isotropic linear elastic material. Predicted the behavior of the femur according to the loading condition, it can be help the development of high-precision artificial bones and joints can be treated with surgery and will be able to perform efficiently.