• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.38-47
• /
• 2005

In this paper, a regenerative braking algorithm is proposed to make the maximum use of the regenerative braking energy for an independent front and rear motor drive parallel HEV. In the regenerative braking algorithm, the regenerative torque is determined by considering the motor capacity, motor efficiency, battery SOC, gear ratio, clutch state, engine speed and vehicle velocity. To implement the regenerative braking algorithm, HEV powertrain models including the internal combustion engine, electric motor, battery, manual transmission and the regenerative braking system are developed using MATLAB, and the regenerative braking performance is investigated by the simulator. Simulation results show that the proposed regenerative braking algorithm contributes to increasing the battery SOC, which recuperates 60 percent of the total braking energy while satisfying the design specification of the control logic. In addition, a control algorithm which limits the regenerative braking is suggested by considering the battery power capacity and dynamic response characteristics of the hydraulic control module.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.8
• /
• pp.63-72
• /
• 1995

Closed-die forging of spur gears with hollow cylindrical billet has been analysed by using the upper-bound method. A kinematically admissible velocity field has been developed, wherein, an involute curve has been introduced to represent the forging die profile. In the analysis, the deformation region has been divided into nine zones. A constant frictional stress has been assumed on the contacting surfaces. Utilizing the formulated velocity field, numerical calculations have been carried out to investigate the effects of various parameters, such as module, number of teeth and friction factor, on the forging of spur gears. Hardness and accuracy of forged gears are measured. The following results have been obtained: (1) It is verified that an axisymmetric deformation zone exists between root circle and center of gear through forged gears. (2) The average relative forging pressure is predominantly dependent on the number of teeth and increases near the final filling stage as the addendum modification coefficient increases. (3) Close agreement was found between the predicted values of forging load and those obtained from experimental results.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.9 no.5
• /
• pp.147-154
• /
• 2009

Lately, superhigh speed network infra is developing with the fast speed, is evolved by step that existent appliances are digitalised and appliances are become remote control by being gear to network. Also, gearing in Home network and superhigh speed network infra, control appliances in Internet and research that do monitering is proceed. Therefore, describe about indoor environment automatic control system that use Wireless sensor and Microcontroler in this paper. Because using that electric power, Zigbee sensor and Wireless module, embodied system that measured in the room temperature and use ATmega128 Microcontroler and use each device (temperature, illumination, humidity) back in house and control humidifier, electric fan etc. Can use variously in Home network field by this Wireless sensor and Microcontroler base, and also can apply variously to several industry fields as well as Home network field.

• Journal of Advanced Navigation Technology
• /
• v.24 no.2
• /
• pp.61-66
• /
• 2020

Since the ocean accounts for 70.8 percent of the earth's surface, the success of IoT technology in the marine industry is to collect information from devices placed in a wider range. LPWA is a feature with a wide range of communication and is very suitable for deployment in the ocean. In this paper, the real-sea performance distance experiment was carried out based on Private LoRa, a key technology for executing the electronic phrase real-name system. A private LoRa module based on sx1276 was developed, and Gateway was developed to transfer data received by private LoRa to the server using SKT Cat. M1. After installing gateways at 599 meters above sea level and experimenting with data transmission and reception at 25 km, 40 km and 60 km, we were able to see that the communication success rate was obtained to be 96.1%. 97.1% and 96.2% respectively.

• Tribology and Lubricants
• /
• v.34 no.2
• /
• pp.43-48
• /
• 2018

This paper presents the thermohydrodynamic analysis of tilting journal pad bearings supporting a power turbine rotor applied to a 250 kW super-critical $CO_2$ cycle. In the analysis, the generalized Reynolds equation and 3D energy equation are solved to predict oil film temperature and the 3D heat conduction equation is solved for pad temperature. The power turbine rotor is supported by two tilting pad bearings consisting of five pads with an oil supply block between the pads. Copper backing pads with higher thermal conductivity compared to steel backing pads are adopted to improve thermal management. The predicted maximum pad temperature is around $55^{\circ}C$ which is approximately $15^{\circ}C$ higher than oil supply temperature. In addition, the predicted minimum film thickness is 50 mm at a rotating speed of 5,000 rpm. These results indicate that there is no issue in the thermal behavior of the bearing. An operation test is performed with a power turbine module consisting of a power turbine, a reduction gear and a generator. Thermocouples are installed at the 75% position from the leading edge of the pad to monitor pad temperature. The power turbine uses compressed air at a temperature of $250^{\circ}C$ in its operation. The steady state pad temperatures measured in the test show good agreement with the predicted temperatures.

• Journal of Advanced Navigation Technology
• /
• v.19 no.4
• /
• pp.288-298
• /
• 2015

For the commercialization of unmanned aircraft, we must validate the safety of the air/ground collision alert systems (CAS). The validation procedure of CAS requires the flight test which is not only expensive but also dangerous. To alleviate this problem, we need the simulation based validation process for the CAS. We developed an integrated UAV simulation (IUS) environment which interconnect the flight simulator, the Matlab/Simulink, and a target avionics simulation model. We developed the collision warning module of the TCAS and tested using IUS and flight encounter models. Using IUS, we can evaluate the performance and reliability of a target avionic system at the preliminary design stage of a development life cycle.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.9
• /
• pp.1228-1236
• /
• 2018

Recently, the maritime environment contaminated by the abandoned fishing gears. To solve this problem, there requires systematic management techniques for the fishing gears based on ICT technologies. The existed systems are optionally used by owners, but the systems need to adopt the monitoring and control architecture for integrated national surveillance. To do this, we designed an architecture for effective monitoring and management which collects position and state information using automatic identification buoy (AIB) device, to send the fishing ship, administrator ship, and shore side control center based on the IoT networks. Especially, in this paper, we developed the ENC-based integrated control system for efficient management which provides functions for position indication, state information display and loss alarm of fishing gears. Also, we conduct performance tests for data processing and visualization functions of the system to use a virtual buoy generation module.