• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.11
• /
• pp.2742-2748
• /
• 2000

In this study, the quantitative evaluation was performed by examination for gatigue crack origin in two prepared ductile irons specimens which have different microstructures using rotary bending fatigue tester, Series A has mixed microstructure. ferrite plus pearlite, and series B has bainitic microstructure. Obtained main results are as follows. The scatterings of fatigue strength were observed on σ(sub)α-Ν diagram of both specimen series, and it is observed that scatterings of series A were more serious. It is reasonable to evaluate the size of mesocrack range by means of √A(원문참조), where A means the area of mesocrack range including globular graphite nodule. As a result of reconsideration for the fatigue data by introduction of K(sub)α-Ν diagram, the scattrings of fatigue life were, remarkably. reduced. Therefore, it is more reasonable to evaluate of mesocrack range on fatigue life by parameter K(sub)α rather than σ(sub)α.

• Korean Journal of Materials Research
• /
• v.12 no.11
• /
• pp.835-839
• /
• 2002

Metal-Ferroelectric-Metal(MFM) capacitors were prepared using $Bi_{3.3}$ $La_{0.7}$ $Ti_3$$O_{12}$ (BLT) ferroelectric thin films which were spin coated on $Pt/Ti/SiO_2$/Si substrates by the Sol-Gel method. BLT thin films annealed at above $650^{\circ}C$ showed polycrystalline structures with typical c-axis preferred orientation. The grain size and surface roughness were increased as the annealing temperature increased from $650^{\circ}C$ to $700^{\circ}C$. In addition, the full width at half maximum (FWHM) values were decreased with increasing annealing temperatures, indicating the improvement of crystallinity. The remanent polarization (2Pr= $Pr^{+}$ $+Pr^{-) }$ and leakage current of the BLT film annealed at $650^{\circ}C$ were about 29.3 $\mu$C/cm$^2$ and $2.3$\times$10^{-8}$$ A/cm^2$ at 3V. There were no distinct changes in the retention charges after $10^{10}$ polarization switching cycles, showing good fatigue property of the annealed BLT films.

• Journal of Ocean Engineering and Technology
• /
• v.5 no.1
• /
• pp.97-105
• /
• 1991

In this paper, the fatigue strength and the fatigue crack propagation behaviors of the round bar specimens which were spirally built up by welding and subsequently hardened by quenching were investigated. The material used was SF60 which was whdely employed in mechanical components, especially shafts. Fatigue tests were conducted at the fully reversed condition(R=-1) and axial and load control in the room temperature ahd air environment. The experimental results were expressed by both the range of stress intensity factor ($\Delta{K}$) and the effective range of stress intensity factor ($\Delta{K}_{eff}$). It was clarified that applying of quenching after the building up welding process improved the fatigue strength and the gatigue crack propagation property in the low range of $\Delta{K}$ of the built up round bar specimen.

• Journal of Welding and Joining
• /
• v.5 no.3
• /
• pp.53-61
• /
• 1987

Post weld heat treatment(PWHT) is usually carried out to remove the residual stress and to improve the microstructure and mechanical properties of welded joints. By the way, welding structure transformed owing to PWHT and reheating for repair loads the random cycles fatigue as offshore welding structure of constant low cycle fatigue as pressure vessel, and then, pre-existing flaws or cracks exist in a structural component and those cracks grow under cyclic loading. Therefore, the effects of PWHT and stress ratio on fatigue crack growth behaviors were studied on the three regions such as HAZ, sub-critical HAZ and deposit metal of welded joints in SM53 steel. Fatigue crack growth behavior of as-weld depended on microstructure and fatigue crack growth rate of HAZ was the lowest at eac region, but after PWHT it was somewhat higher than that of as-wel. In case of applying the stress($10kg/mm^2$) during PWHT, fatigue crack growth resistance tended to increase in the overall range of .DELTA.K.