• 한국자동차공학회논문집
• /
• 제14권5호
• /
• pp.25-31
• /
• 2006

Controlled Auto Ignition(CAI) combustion has great potential in achieving significant increase in engine efficiency, while simultaneously reducing exhaust emissions. The process itself involves the auto ignition and subsequent simultaneous combustion of a premixed charge. In this study, NVO(Negative Valve Overlap) system was applied to a CAI engine in order to use residual gas. The fuel was injected directly to the cylinder under the high temperature condition resulting from heating the intake port to initiate CAI combustion. This paper introduced the valve timing strategy and experimental set-up. From this study, the effect of engine speed and valve timing on CAI combustion and exhaust emissions was clarified. In addition, stratified charge method was used to extend CAI operating region.

• 에너지공학
• /
• 제25권4호
• /
• pp.159-169
• /
• 2016

본 연구에서는 함산소기재 중 MTBE를 휘발유에 첨가하여 산소함량(0, 1.0, 2.3 및 2.7 wt %)의 변화에 따라 MPI 및 GDi 차량에서 배출되는 유해한 배출가스와 연비를 분석하였다. 국내 및 미국의 연비시험방법인 FTP-75 mode와 HWFET mode를 적용하였다. CO, NMHC, NOx 배출량은 산소함량의 변화에 따라 미미한 차이는 있었지만 상관관계는 없었다. FTP-75 mode에서 CO2 배출량은 산소함량의 변화에 따라 증감의 경향성은 없었다. 하지만 차량이 예열된 상태이고 고속 운전영역이 포함된 FTP-75 mode의 phase-3와 HWFET mode에서는 산소를 함유한 연료의 CO2 배출량이 적었다. 입자개수 배출량은 산소함량과 음의 상관관계를 보였으며 산소함량 2.3 wt %에서 가장 적었다. 카본발란스법에 의해 계산된 연비는 산소를 함유한 연료가 높았으며 2.3 wt %에서 가장 높았다.

• 한국소음진동공학회논문집
• /
• 제22권10호
• /
• pp.985-993
• /
• 2012

In this paper, a new method is proposed to estimate the sound pressure generated from gasoline direct injection (GDI) engine. There are many noise sources as much as components in GDI engine. Among these components, fuel pump, fuel injector, fuel rail, pressure pump and intake/exhaust manifolds are major components generated from top of the engine. In order to estimate the contribution of these components to engine noise, the total sound pressure at the front of the engine is estimated by using airborne source quantification (ASQ) method. Airborne source quantification method requires the acoustic source volume velocity of each component. The volume velocity has been calculated by using the inverse method. The inverse method requires many tests and has ill-condition problem. This paper suggested a method to obtain volume velocity directly based on the direct measurement of sound intensity and particle velocity. The method is validated by using two known monopole sources installed at the anechoic chamber. Finally the proposed method is applied to the identification and contribution of noise sources caused by the GDI components of the test engine.

• 대한기계학회논문집B
• /
• 제26권5호
• /
• pp.724-732
• /
• 2002

Although the demands for diesel engine is increased, our world is faced with very serious problems related to the air pollution due to the exhaust emissions of the diesel engine. In this study, the potential possibility of oxygenated fuel such as Methyl tertiary butyl ether (MTBE) was investigated for the sake of exhausted smoke reduction from diesel engine. MTBE has been used as a fuel additive blended into unleaded gasoline to improve octane number, but the study of application for diesel engine was incomplete. Because MTBE includes oxygen content approximately 18%, it is a kind of oxygenated fuel that the smoke emission of MTBE is reduced remarkably compared with commercial diesel fuel, that is, it can supply oxygen component sufficiently at high load and speed in diesel engine. But, the NOx emission of MTBE blended fuel is increased compared with commercial diesel fuel. And. it was tried to analyze not only total hydrocarbon but individual hydrocarbon components from $C_1$to $C_{6}$ in exhaust gas using gas chromatography to seek the reason for remarkable reduction of smoke emission. The results of this study show three conclusions. 1. The smoke omission of the MTBE blended fuel is lower than that of the diesel fuel at all experimental region in direct injection diesel engine. 2. Individual hydrocarbons(C$_1$~ $C_{6}$) as well as total hydrocarbon of oxygenated fuel are reduced remarkably compared with diesel fuel. 3. Smoke emission from diesel engines was strongly depended on oxygen content in fuel regardless of operating condition.

• 대한기계학회논문집B
• /
• 제25권10호
• /
• pp.1303-1310
• /
• 2001

In order to be applicable to the combustion modelling of stratified charged combustion like that of - lean burn and GDI engine, the correlations of laminar burring velocities fur several hydrocarbon fuels and methanol are needed over a wide range of equivalence ratio, pressure and temperature. In this study, these correlations are modeled in the 1311owing form based on the experimental and Muller\`s modeling results for several fuels, where $\alpha$, ξ, and ξ are functions of pressure and temperature, $S_{L}$ =$\alpha$ exp[-ξ($\Phi$-$\Phi$$_{m}$)$^{2}$ -exp {-ζ($\Phi$-$\Phi$$_{m}$)}-ζ($\Phi$-$\Phi$$_{m}$)]. By using the results calculated by PREMIX code with Sloane\`s detailed chemical reaction mechanism for propane, it is verified that the coefficients of the abode modeling can be determined by considering laminar burning velocity data only in a range of equivalence ratio less than $\Phi$$_{m}$. Therefore, Muller\`s modeling results can be adopted leer modeling of the pressure and temperature dependency. Compared with the results of the existing Keck'and Gulder's models, those of the present one showed the good agreement of the recent experimental data, especially in the range of lean and rich sides.s.des.s.

• 한국자동차공학회논문집
• /
• 제14권2호
• /
• pp.100-106
• /
• 2006

The behavior of spray impinging on the inclined constant temperature flat plate was experimentally investigated. To clarify the wall effect of a high pressure DISI injector, a relative angle of the inclined wall to a spray axis was varied. Spray penetration along the wall was observed optically and it was compared with that of a Fan spray type and Swirl type spray. To evaluate various spray motion quantitatively, a spray path penetration which describe the development of a spray tip along the wall was newly introduced. To observe the structure of an impinging spray, it was visualized by a controlled stroboscope light and its visualized image was captured on an CCD camera. Using the digital image of impinging spray $H_x$ and $R_x$ was extracted to clarify the structure of impinging spray. The main parameter of the relative position of the wall was the inclined angle which was defined as the angle was varied from $0^{\circ}$ (vertical impingement) to $60^{\circ}$ at the same condition.

• 한국분무공학회지
• /
• 제25권4호
• /
• pp.162-169
• /
• 2020

The worldwide focus on reducing the emissions, fuel and lubricant consumption in T-GDI engines is leading engineers to consider the crankcase ventilation and oil mist separation system as an important means of control. In today's passenger cars, the oil mist separation systems mainly use the inertia effect (e.g. labyrinth, cyclone etc.). Therefore, this study has investigated high efficiency cylinder head-integrated oil-mist separator by using a compact multi-impactor type oil mist separator system to ensure adequate oil mist separation performance. For this purpose, engine dynamometer testing with oil particle efficiency measurement equipment and 3D two-phase flow simulation have been performed for various engine operating conditions. Tests with an actual engine on a dynamometer showed oil aerosol particle size distributions varied depending on operating conditions. For instance, high rpm and load increases bot only blow-by gases but the amount of small size oil droplets. Submicron-sized particles (less than 0.5 ㎛) were also observed. It is also found that the impactor type separator is able to separate nearly no droplets of diameter lower than 3 ㎛. CFD results showed that the complex aerodynamics processes that lead to strong impingement and break-up can strip out large droplets and generate more small size droplets.

• 한국가스학회지
• /
• 제27권3호
• /
• pp.52-58
• /
• 2023

지구 기상이변에 대해 탄소중립의 중요성이 대두됨에 따라 무탄소 연료인 수소의 에너지원으로서의 활용도 역시 증대되고 있다. 일반적으로 수소는 연료전지(FC, Fuel Cell)에 활용되고 있으나, 이는 연소를 기반으로 하는 내연기관(ICE, Internal Combustion Engine)에도 활용될 수 있다. 특히 연료전지만으로 수소 활용 및 인프라 확장이 어려운 때에 이미 생산 측면이나 공급 측면에서 인프라가 기 구축되어 있는 내연기관은 수소 에너지 저변 확대에 큰 도움을 줄 수 있다. 다만 수소를 연소기반으로 활용할 경우 고온에서 공기 중 질소가 산소와 반응하여 유해배기물질인 질소산화물(NOx, Nitrogen Oxides)이 생성될 수 있는 단점은 존재한다. 특히 냉간 (Cold Start) 운전 영역시 포함될 EURO-7 배기규제의 경우 워밍업(Warm-up) 과정에서 발생하는 배기배출물의 저감을 위한 노력도 필요하다. 따라서 본 연구에서는 2 L급 수소 직접분사방식 전기점화 (SI, Spark Ignition) 엔진을 활용하여 냉각수를 상온에서 88 ℃로 워밍업하는 과정에서 질소산화물 및 연료소모율의 변화 특성을 살펴보았다. 특히 수소는 기존의 가솔린, 천연가스, 액화석유가스(LPG, Liquified Petroleum Gas)와 달리 가연범위(Flammable range)가 넓기 때문에 공기과잉률(Excessive air ratio)을 희박하게 조절할 수 있다는 장점이 있다. 이에 본 연구에서는 워밍업하는 과정에 있어서 공기과잉률을 1.6/1.8/2.0으로 변화하여 그 결과를 분석하였다. 본 실험의 결과는 워밍업 시 공기과잉률이 희박해질수록 시간당 질소산화물의 배출이 적고, 열효율도 상대적으로 높으나 최종 온도까지 도달 시간이 길어짐에 따라 누적 배출량 및 연료소모율은 악화될 수도 있음을 시사한다.