• 한국지하수토양환경학회지:지하수토양환경
• /
• 제12권6호
• /
• pp.60-69
• /
• 2007

토양에서 휘발성 유기화합물(VOC, volatile organic compound)의 유동특성을 이해하는 것은 오염물질의 확산을 예측하고 오염의 정도를 평가하며 대책을 수립하는 데 있어서 매우 중요하다. 토양과 같은 다공성매질에서 유동하는 물질의 출현곡선에 대한 모멘트의 분석을 통하여 화학물질의 유동속도, 플룸의 폭 및 비대칭정도를 평가할 수 있다. 본 연구에서는 실험실 규모의 토양 컬럼실험을 사용하여 VOC의 가스상 유동실험을 실시하였으며, 모두 네 가지의 VOC에 대하여 포화도(water saturation)범위 0.04-0.46에서 출현곡선을 측정하였다. 또한 포화도 0.21에서 열한가지의 VOC에 대하여 출현곡선을 측정하였다. 측정된 출현곡선의 중심 2차(central second)및 중심 3차(central third)모멘트는 포화도와 1차 모멘트(또는 지체상수)와 비교 분석되었다. VOC 출현곡선의 모멘트분석 결과 2차 및 3차 모멘트는 1차 모멘트의 2.23제곱 및 3.16제곱 함수로서 증가하였으며, 3차 모멘트가 2차 모멘트에 대하여 보다 민감하게 반응하였다. 이는 VOC가 토양가스상에서 이동할 때, 지체상수에 비례하여 가스 플룸의 폭과 비대칭성이 증가한다는 사실을 나타낸다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제16권3호
• /
• pp.380-383
• /
• 2003

The gas dilution technique was used to evaluate the possibility of estimating the volume of gaseous phase in the rumen from its composition in sheep given rice whole crop silage (RWS) or dent corn silage (DCS) at a level of maintenance (M) or 2 M, and in the course of fasting. The rumen gas composition was determined at 2 and 7.5 h after morning feeding. Nitrogen gas was injected by using an airtight syringe into the rumen immediately after collecting the rumen gas sample as a control. Then rumen gas samples were collected at 5, 10, 20, 40 and 60 min. after injection. Dry-matter intakes were $42g/kg^{0.75}$ and $57g/kg^{0.75}$ for DCS, and $36g/kg^{0.75}$ and $59g/kg^{0.75}$ for RWS, at 1 M and 2 M levels, respectively. Animals ingested both silages about 20% less than expected at 2 M level. The rumen gas composition did not differ significantly between 2 h and 7.5 h after feeding except for $N_2$. Content of $CO_2$ in gas composition was significantly higher at 2 M level than at 1 M (p<0.05) for both RWS and DCS, whereas $CH_4$ showed no significant difference between feeding levels. At both feeding levels, $CO_2$ showed a higher (p<0.05) percentage in DCS than RWS. A dilution technique by using $N_2$ injection is not appropriate for the determination of gas production in vivo, unless the rate of rumen gas turnover is considered. Changes in composition at fasting indicate that the rumen fermentation may reach the lowest level after 72 h fasting for sheep given silage as their sole diet.

• Journal of Korean Society for Atmospheric Environment
• /
• 제23권E1호
• /
• pp.16-28
• /
• 2007

An improved method was developed to determine gas-phase hydrogen peroxide($H_2O_2$) and organic hydro-peroxides (ROOH) in real-time, The analytical system for $H_2O_2$ is based on formation of hydroxybenzoic acid (OHBA), a strong fluorescent compound. OHBA is formed by a sequence of reactions, photoreduction of Fe(III)-EDTA to Fe(II)-EDTA, the Fenton reaction of Fe(II)-EDTA with $H_2O_2$, and hydroxylation of benzoic acid. By use of this analytical method rather than a previous similar method, Fenton reaction time was reduced from 2 min. to 30s. Air samples were collected by a surfaceless inlet to prevent inlet line losses. With a special arrangement of the sampling apparatus, sample delivery time was drastically reduced from ${\sim}5\;min\;to\;{\sim}20\;s$. The automated system was found to be sensitive, capable of continuous monitoring, and affordable to operate. A comparison of this method with a well-established one showed an excellent linear correlation, validating applicability of this technique to $H_2O_2$ determination. The system was applied to field measurements conducted during summertime of 2004 in Gwangju, South Korea. $H_2O_2$ was found to be a predominant species of peroxides. The diurnal variation of $H_2O_2$ displayed the maximum in early afternoon and the broad minimum throughout night. $H_2O_2$ was correlated positively with ozone, photochemical age, and temperature, however, negatively with $NO_x$ and relative humidity.

• 한국표면공학회지
• /
• 제43권5호
• /
• pp.238-242
• /
• 2010

In the present work, the influence of oxide on the Cr-Si-N coatings was investigated for the Cr-Si-O-N coatings on AISI 304 and Si wafer deposited by hybrid system, which combines the DC magnetron sputtering technique and arc ion plating (AIP) using Cr and Si target in an $Ar/N_2/O_2$ gaseous mixture. As the O content in the Cr-Si-N coatings increased, the diffraction patterns of the Cr-Si-O-N coatings showed CrN and $Cr_2O_3$ phases. However, as the O content increased to 28.8 at.%, diffraction peak of $Cr_2O_3$ was disappeared in the Cr-Si-O-N coating. The $d_{200}$ value was decreased with increasing of O content. The average grain size increased from about 40 nm to 65 nm as the O content increased. The maximum micro-hardness of the Cr-Si-O-N coating was obtained 4507 Hk at the O content of 24.8 at.%. The average friction coefficient of the Cr-Si-O-N coatings was gradually decreased by increasing the O content and the average friction coefficient decreased from 0.37 to 0.25 by increasing the O content. These results indicated that amorphous phase was increased in the Cr-Si-O-N coatings by increasing of O content.

• 대한화학회지
• /
• 제55권1호
• /
• pp.92-97
• /
• 2011

비닐 아세트산염 합성에 대한 1족 알칼리금속 아세트산염의 촉진 효과를 조사하였다. Pd-Au/$SiO_2$ 촉매를 사용한 경우와 사용하지 않은 경우에 대해 에틸렌과 아세트산 간의 기체상 반응에 대해 생성물 선택성과 에틸렌 전환을 비교하였다. 촉진제가 촉매 표면을 안정화시켰으며, 생성물 선택성과 에틸렌 전환을 촉진하였다. 이 촉매 효과는 1족에서 위에서 아래로 내려갈수록 증가하였다. 이것은 아세트산염의 공통이온효과 때문이다.

• Nuclear Engineering and Technology
• /
• 제45권2호
• /
• pp.203-210
• /
• 2013

The objective of this conducted research is to study the iodine removal efficiency in a self-priming venturi scrubber for submerged and non-submerged operating conditions experimentally and theoretically. The alkaline solution is used as an absorbent, which is prepared by dissolving sodium hydroxide (NaOH) and sodium thiosulphate ($Na2S_2O_3$) in water to remove the gaseous iodine ($I_2$) from the gas. Iodine removal efficiency is examined at various gas flow rates and inlet concentrations of iodine for submerged and non-submerged operating conditions. In the non-submerged venturi scrubber, only the droplets take part in iodine removal efficiency. However, in a submerged venturi scrubber condition, the iodine gas is absorbed from gas to droplets inside the venturi scrubber and from bubbles to surrounding liquid at the outlet of a venturi scrubber. Experimentally, it is observed that the iodine removal efficiency is greater in the submerged venturi scrubber as compare to a non-submerged venturi scrubber condition. The highest iodine removal efficiency of $0.99{\pm}0.001$ has been achieved in a submerged self-priming venturi scrubber condition. A mathematical correlation is used to predict the theoretical iodine removal efficiency in submerged and non-submerged conditions, and it is compared against the experimental results. The Wilkinson et al. correlation is used to predict the bubble diameter theoretically whereas the Nukiyama and Tanasawa correlation is used for droplet diameter. The mass transfer coefficient for the gas phase is calculated from the Steinberger and Treybal correlation. The calculated results for a submerged venturi scrubber agree well with experimental results but underpredicts in the case of the non-submerged venturi scrubber.

• 한국수소및신에너지학회논문집
• /
• 제23권5호
• /
• pp.559-571
• /
• 2012

Dimethyl ether (DME) is a new clean fuel as an environmentally-benign energy resource. DME can be manufactured from various energy sources including natural gas, coal, and biomass. In addition to its environmentally friendly properties, DME has similar characteristics to those of LPG. The aim of this article is to represent the development of new DME process with KOGAS's own technologies. KOGAS has investigated and developed new innovative DME synthesis process from synthesis gas in gaseous phase fixed bed reactor. DME has been traditionally produced by the dehydration of methanol which is produced from syngas, a product of natural gas reforming. This traditional process is thus called the two-step method of preparing DME. However, DME can also be manufactured directly from syngas (single-step). The single-step method needs only one reactor for the synthesis of DME, instead of two for the two-step process. It can also alleviate the thermodynamic limitations associated with the synthesis of methanol, by converting the produced methanol into DME, thereby potentially enhancing the overall conversion of syngas into DME. KOGAS had launched the 10 ton/day DME demonstration plant project in 2004 at Incheon KOGAS LNG terminal. In the mid of 2008, KOGAS had finished the construction of this plant and has successively finished the demonstration plant operation. And since 2008, we have established the basic design of commercial plant which can produce 3,000 ton/day DME.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 Techno-Fair 및 추계학술대회 논문집 전기물성,응용부문
• /
• pp.124-125
• /
• 2007

The composites were fabricated $\beta$-SiC and $TiB_2$ powders with the liquid forming additives of 8, 12, 16[wt%] $Al_2O_3+Y_2O_3$ as a sintering aid by pressureless annealing at $1,650[^{\circ}C]$ for 4 hours. Reactions between SiC and transition metal $TiB_2$ were not observed in the microstructure and the phase analysis of the pressureless annealed SiC-$TiB_2$ electroconductive ceramic composites. The relative density, the flexural strength, the Young's modulus and the Vicker's hardness showed the highest value of 82.29[%], 189.5[MPa], 54.60 [GPa] and 2.84[GPa] for SiC-$TiB_2$ composites added with 16[wt%] $Al_2O_3+Y_2O_3$ additives at room temperature. The relative density of SiC-$TiB_2$ composites was lowered due to gaseous products of the result of reaction between SiC and $Al_2O_3+Y_2O_3$. The electrical resistivity showed the lowest value of 0.012[${\Omega}{\cdot}cm$] for 16[wt%] at 25[$^{\circ}C$]. The electrical resistivity was all negative temperature coefficient resistance (NTCR) in the temperature ranges from 25[$^{\circ}C$] to 700[$^{\circ}C$].

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.383-383
• /
• 2010

Gas-phase hydrogen atoms create a variety of chemical and physical phenomena on Si surfaces: adsorption, abstraction of pre-adsorbed H, Si etching, Si amorphization, and penetration into the bulk lattice. Thermal desorption/evolution analyses exhibited three distinct peaks, including one from the crystalline bulk. It was previously found that thermal-energy gaseous H(g) atoms penetrate into the Si(100) crystalline bulk within a narrow substrate temperature window(centered at ~460K) and remain trapped in the bulk lattice before evolving out at a temperature as high as ~900K. Developing and sustaining atomic-scale surface roughness, by H-induced silicon etching, is a prerequisite for H absorption and determines the $T_s$ windows. Issues on the H(g) absorption to be further clarified are: (1) the role of the detailed atomic surface structure, together with other experimental conditions, (2) the particular physical lattice sites occupied by, and (3) the chemical nature of, absorbed H(g) atoms. This work has investigated and compared the thermal H(g) atom absorptivity of Si(100), Si(111) and Si(110) samples in detail by using the temperature programmed desorption mass spectrometry (TPD-MS). Due to the differences in the atomic structures of, and in the facility of creating atom-scale etch pits on, Si(100), (100) and (110) surfaces, the H-absorption efficiency was found to be larger in the order of Si(100) > Si(111) > Si(110) with a relative ratio of 1 : 0.22 : 0.045. This intriguing result was interpreted in terms of the atomic-scale surface roughening and kinetic competition among H(g) adsorption, H(a)-by-H(g) abstraction, $SiH_3(a)$-by-H(g) etching, and H(g) penetraion into the crystalline silicon bulk.

• 한국응용과학기술학회지
• /
• 제34권4호
• /
• pp.892-898
• /
• 2017

본 연구에서는 자원내 포함된 역청의 경질화 과정에서 배출 및 회수되는 가스상 물질 및 고체상 물질을 활용하기 위한 기초 성상이 조사되었다. 이를 위하여 열분해 온도 별 역청성 오일의 전환에 대한 열분해반응 기초특성이 조사되었다. 또한 실험실 규모의 고정층 반응기를 이용하여 반응온도에 따른 가스 및 고체상 분산물의 특성을 조사하였다. 그 결과 $550^{\circ}C$에서 약 17%의 오일 수율을 얻었으며, 부산물로는 $CH_4$, $CaCO_3$ 및 CaO를 회수할 수 있음을 확인하였다.