• 대한기계학회논문집
• /
• 제11권5호
• /
• pp.828-836
• /
• 1987

본 연구에서는 유동장과 입자의 부착율과의 관계에 대해 고찰하기 위하여 부 착되는 고체 벽면의 형상을 원통형으로 하여 비등온 유동에서 열확산에 의한 미소입자 의 원주방향으로의 부착율을 측정하고, 원통 내부의 냉각장치를 이용하여 벽면과 고온 가스와의 온도 차이를 크게하여(약 400∼700˚K), 높은 온도구배 영역에서의 열확산 효과에 대해 실험적인 연구를 확장시킴으로써 폭넓은 온도구배 영역에서의 열확산 이 론의 타당성을 검토한다. 그리고 이러한 실험결과들은, 원통주위의 미소입자 전달에 관한 종래의 Levich 등의 해와 입자의 미소한 관성의 영향을 동시에 고려한 Fernandez de la Mora 등의 점근적인(asymptotic)이론과 비교될 것이다.

• 한국입자에어로졸학회지
• /
• 제13권3호
• /
• pp.119-125
• /
• 2017

A novel two stage cylindrical cyclone was developed for a 3 phase separator in shale oil production industry. The cyclone performance was compared with a cone type cyclone and multi cyclone at the same experimental condition using water and oil mists generated by a humidifier and atomizer at the flow rate 1 to $2m^3/min$. The removal efficiency of total suspended water droplets by the novel cyclone, calculated using inlet and outlet concentrations measured by an optical particle counter, was 99% which is higher than 90% of oil droplet removal efficiency at $2m^3/min$. It might be due to the evaporation of small water droplets during the tests. The water and oil droplet removal performance of the novel cyclone based on the quality factor which is a function of pressure drop and removal efficiency was the highest among three cyclones. The results indicate that the cyclone could be an economical device to remove water and oil mists from shale gas generation processes where a huge three phase separator is commonly used.

• 설비공학논문집
• /
• 제15권4호
• /
• pp.268-273
• /
• 2003

In the present study, the characteristics of upward bubble flow were experimentally investigated in a liquid bath. An electro-conductivity probe was used to measure local volume fraction and bubble frequency. Since the gas is concentrated at the near nozzle, the flow parameters are high near the nozzle. In general their axial and radial values tended to decrease with increasing distance. For visualization of flow characteristics, a Particle Image Velocimetry (P.I..V) and a thermo-vision camera were used in the present study. The experimental results show that heat transfer from bubble surface to water is largely completed within z=10mm from the nozzle, and then the temperature of bubble surface reaches that of water rapidly. Due to the centrifugal force, the flow was more developed near the wall than at bubble-water plume. Vortex flow in the bottom region was relatively weaker than that in the upper region.

• 항공우주기술
• /
• 제9권1호
• /
• pp.17-27
• /
• 2010

알루미나 입자가 포함된 KSLV-I KM 고공 플룸 유동을 연소실에서 노즐 출구의 고공 팽창과정을 해석하였다. 알루미나 입자 및 플룸 가스의 물성치 및 분포를 달리하여 해석한 결과 연소가스 비열비를 1.2로 알루미나 입자의 직경 분포를 7가지로 가정하면 노즐 내부 유동 특성이 평형유동 해석 결과와 비교적 일치하였다. 입자의 팽창각은 가스유동보다 작으며 입자 직경이 클수록 팽창각은 더 작았다. 알루미나 입자의 광학 열물성을 변화시키며 KM TVC 분배기 위치의 복사열을 계산한 결과 알루미나 입자의 방사율이 0.1일 때 비행시험 결과와 비슷한 수준을 예측하였다.

• 대한기계학회논문집B
• /
• 제23권6호
• /
• pp.778-787
• /
• 1999

In this study, the autoignition process of liquid fuel, injected into hot and stagnant air in a 2-D axisymmetric confined cylindrical combustor, has been investigated. Eulerian-Lagrangian scheme was adopted to analyze the two-phase flow and combustion. The unsteady conservation equations were used to solve the transition of the gas field. Interactions between two phases were accounted by using the particle source in cell (PSI-Cell) model, which was used for detailed consideration of the finite rates of transports between phases. And infinite conduction model was adopted for the vaporization of droplets. The results have shown that the process of the autoignition consists of heating up of droplets, vaporization, mixing and ignition. The ignition criteria could be determined by the temporal variations of temperature, reaction rate and species mass fraction. And the effects of various parameters on ignition phenomena are examined. These have shown that the increasing the reaction rate and/or the vaporization rate can reduce the ignition delay time.

• 한국분말재료학회지
• /
• 제11권6호
• /
• pp.515-521
• /
• 2004

Fe(C) nanocapsules were prepared by the chemical vapor condensation(CVC) process using the pyrolysis of iron pentacarbonyl $(Fe(CO)_5)$. Their characterizations were studied by means of X-ray diffraction, X-ray photoelectron spectrometer and transmission electron microscopy. The long-chained Fe(C) nanocapsules hav-ing the mean size of under 70 nm could be obtained below $1100^{\circ}C$ in different gas flow rates. The particle size of the powders was increased with increasing decomposition temperature, but it was decreased with increasing CO gas flow rate. The Fe powders produced at $500^{\circ}C$ consisted of three layers of ${\alpha}$-Fe/$Fe_3C$/amorphous phases, but it had two phase core-shell structure which consited of $Fe_3C$ phase of core and graphite of shell at $1100^{\circ}C$.

• 대한조선학회논문집
• /
• 제54권6호
• /
• pp.470-475
• /
• 2017

Since the intake air of gas turbine engine of marine purpose contains water particles, inertial separator for separating the air and water particles are provided. Saw type and wave type separator are now used to separate inflow water particle from the gas. In this paper, the design parameters of saw type separator are studied by numerical simulations. Using the commercial CFD program, Star-CCM+, Lagrangian-Eulerian method was used to perform the analysis of two phase flow of the mist in the air. This method solves Reynolds-Averaged Navier-Stokes equations in Eulerian framework for the continuous phase, while solves equation of motion for individual particles in Lagrangian framework. Lagrangian multiphase method was applied to monitor the particles of different sizes and shapes and to verify collision between particles by chasing particles. Water particles were injected through injectors located at the inlet of the separator and escape mode was used which assumes that the particles attached on the surface of inertial separator were removed from the simulation, effectively escaping the solution domain. Through the numerical computations with the inlet condition of constant water particle size in the wetness fraction of 85%, efficiency of eliminating the water particle and the pressure drop between the inlet and outlet were examined.

• 열처리공학회지
• /
• 제10권4호
• /
• pp.232-236
• /
• 1997

A rectangular type circulating fluidized bed (CFB) with an internal nozzle and two partition walls was proposed. In this modified CFB, an internal nozzle and two slanted partition walls were additionally set in the riser. This cold mode apparatus was made of acrylic resin; the riser was 1500mm high and $1000{\times}1000mm^2$ in the cross sectional area, the internal nozzle was 200mm high and 10mm in the inner diameter, and the partition wall was 7mm thick. Glass beads of $91{\mu}m$ in the mean diameter were employed as bed materials. In the cold mode by using the proposed CFB with an internal nozzle, it was possible to change the particle hold up by changing the gas flow ratio of the nozzle to the total(Qn/Qt). It was found that the inflection point which devided the bed structure between the dense and the dilute phase in the riser varied with Qn/Qt.

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.2073-2082
• /
• 1991

본 연구에서는 선회유동과 재순환영역이 있는 제한된 동축 분류유동(confined coaxial jet flow)을 갖는 연소기에 대하여 노즐을 통하여 분사된 연료액적의 증발 및 연소, 그리고 주위기체유동에 관한 제반현상을 정상상태 하에서 모사하고자 하는데 그 목적이 있으며 수치계산에 의한 이론적 해석방법으로 기상은 오일러 방식, 액상은 라 그란지 방식을 채택하였고 후술될 증발 및 연소모델을 적용하였다.

• 한국분무공학회지
• /
• 제25권4호
• /
• pp.162-169
• /
• 2020

The worldwide focus on reducing the emissions, fuel and lubricant consumption in T-GDI engines is leading engineers to consider the crankcase ventilation and oil mist separation system as an important means of control. In today's passenger cars, the oil mist separation systems mainly use the inertia effect (e.g. labyrinth, cyclone etc.). Therefore, this study has investigated high efficiency cylinder head-integrated oil-mist separator by using a compact multi-impactor type oil mist separator system to ensure adequate oil mist separation performance. For this purpose, engine dynamometer testing with oil particle efficiency measurement equipment and 3D two-phase flow simulation have been performed for various engine operating conditions. Tests with an actual engine on a dynamometer showed oil aerosol particle size distributions varied depending on operating conditions. For instance, high rpm and load increases bot only blow-by gases but the amount of small size oil droplets. Submicron-sized particles (less than 0.5 ㎛) were also observed. It is also found that the impactor type separator is able to separate nearly no droplets of diameter lower than 3 ㎛. CFD results showed that the complex aerodynamics processes that lead to strong impingement and break-up can strip out large droplets and generate more small size droplets.