• 한국컴퓨터정보학회논문지
• /
• 제22권1호
• /
• pp.63-69
• /
• 2017

In this paper, we propose a method to optimize the geometry and installation position of the mixer in the selective catalytic reduction (SCR) system by computational fluid dynamic(CFD). Using the commercial CFD software of CFD-ACE+, the flow dynamics of the flue gas was numerically analyzed for improving the injection uniformity of the reduction agent. Numerical analysis of the mixed gas heat flow into the upstream side of the primary SCR catalyst layer was performed when the denitrification facility was operated. The characteristics such as the flow rate, temperature, pressure loss and ammonia concentration of the mixed gas consisting of the flue gas and the ammonia reducing gas were examined at the upstream of the catalyst layer of SCR. The temperature difference on the surface of the catalyst layer is very small compared to the flow rate of the exhaust gas, and the temperature difference caused by the reducing gas hardly occurs because the flow rate of the reducing gas is very small. When the mixed gas is introduced into the SCR reactor, there is a slight tendency toward one wall. When the gas passes through the catalyst layer having a large pressure loss, the flow angle of the exhaust gas changes because the direction of the exhaust gas changes toward a smaller flow. Based on the uniformity of the flow rate of the mixed gas calculated at the SCR, it is judged that the position of the test port reflected in the design is proper.

• Composites Research
• /
• 제35권3호
• /
• pp.121-126
• /
• 2022

Owing to advantages of polymeric materials for hydrogen tank liner like light-weight property and high specific strength, polymer based composites have gained much attention. Despite of many benefits, polymeric materials for fuel cell tank cause problems which is critical to applications as low gas barrier property, and poor processability when adding fillers. For these reasons, improving gas barrier property of polymer composites is required to study for expanding application fields. This work presents impermeable polymer nanocomposites by introducing thin barrier coating using layer by layer (LBL) deposition method. Also, bi-layered and quad-layered nanocomposites were fabricated and compared for identifying relationship between deposition step and gas barrier property. Reduction in gas permeability was observed without interrupting mechanical property and processability. It is discussed that proper coating conditions were suggested when different coating materials and deposition steps were applied. We investigated morphology, gas barrier property and mechanical properties of fabricated nanocomposites by FE-SEM, Oxygen permeation analyzer, UTM, respectively. In addition, we revealed the mechanism of barrier performance of LBL coating using materials which have high aspect ratio.

• 한국군사과학기술학회지
• /
• 제21권2호
• /
• pp.195-203
• /
• 2018

Among the techniques of reducing the drag to increase the speed of underwater moving bodies, we studied on the drag reduction method by gas injection. Researches on gas injection method have been paid much attention to reduce the drag of vessels or pipe inner walls. In this study, we used a sintered metal mesh that can uniformly distribute fine bubbles by gas injection method, and applied it to a cylindrical underwater moving body. Using the KRISO medium-sized cavitation tunnel, we measured both the bubble size on the surface of the sintered mesh and the bubble distribution in the boundary layer. Then, drag reduction tests were performed on the cylinder type underwater moving models with cylindrical or round type tail shape. Experiments were carried out based on the presence or absence of tail jet injection. In the experiments, we changed the gas injection amount using the sintered mesh gas injector, and changed flow rate accordingly. As a result of the test, we observed increased bubbles around the body and confirmed the drag reduction as air injection flow rate increased.

• Journal of Magnetics
• /
• 제11권3호
• /
• pp.103-107
• /
• 2006

In grain oriented electrical steel process, hot band annealing has thought to be essential for obtaining good magnetic properties. New hot rolling method of heavy reduction in early hot rolling stage was applied to obtain good magnetic properties in GO process without hot band annealing. Hot rolling was carried out by varyinghot rolling reduction distribution along hot rolling pass. The heavy hot rolling reduction in rear stand improves the magnetic flux density in the case of no hot band annealing. The hot band specimens of the heavy reduction in front stand shows the elongated hot deformed microstructures in the center layer and strong {001}<110> texture.On the contrary, the heavily reduced specimens in rear stand shows the recrystallization in the center layer of hot band and strong {111}<112> and {110}<001> textures.

• 대한조선학회논문집
• /
• 제58권3호
• /
• pp.144-157
• /
• 2021

Brake Horse Power (BHP) reduction ratios by air injection to the underside of the hull surface in an actual ship are predicted using an unstructured finite-volume CFD solver and compared with the sea trial results. In addition, air lubrication system installed on the existing vessel is investigated to find a good solution for additional drag reduction. As a results, it is found that the thickness of the air layer should be minimized within a stable range while securing the area covered by the air layer as much as possible. Furthermore, the amount of frictional drag reduced by air injection is found to be independent of surface roughness and still effective on rough surface. Based on the results of this study, it is expected that systematic and reliable air lubrication system can be designed and evaluated using the proposed method.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.407-409
• /
• 2006

Geochemical analyses carried out on samples collected from cores on and near the southern smit of Hydrate Ridge have advanced understanding by providing a clear contrast of the two major modes of marine gas hydrate occurrence. High concentrations (15%-40% of pore space) of gas hydrate occurring at shallow depths (0-40 mbsf) on and near the southern summit are fed by gas migrating from depths of as much as 2km within the accretionary prism. This gas carries a characteristic minor component of C2-C5 thermogenic hydrocarbons that enable tracing of migration pathways and may stabilize the occurrence of some structure II gas hydrate. A structure II wet gas hydrate that is stable to greater depths and temperatures than structure I methane hydrate may account for the deeper, faint second bottom simulating reflection (BSR2) that occurs on the seaward side of the ridge. The wet gas is migrating In an ash/turbidite layer that intersects the base of gas hydrate stability on the seaward side of and directly beneath the southern summit of Hydrate Ridge. The high gas saturation (>65%) of the pore space within this layer could create a two-phase (gas + solid) system that would enable free gas to move vertically upward through the gas hydrate stability zone. Away from the summit of the ridge there is no apparent influx of the gas seeping from depth and sediments are characterized by the normal sequence of early diagenetic processes involving anaerobic oxidation of sedimentary organic matter, initially linked to the reduction of sulfate and later continued by means of carbonate reduction leading to the formation of microbial methane.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.287-292
• /
• 2001

The objective of this study is to verify the secondary flow and the total pressure loss distribution in the boundary layer fence installed linear turbine cascade passage and to propose an appropriate height of the boundary layer fence which shows the best loss reduction among the simulated fences. In this study three different boundary layer fence was installed which have different height. This study was performed by numerical method and the result showed the boundary layer fence which has the height of one third of the inlet boundary layer thickness showed the best loss reduction rate.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.188-191
• /
• 2008

There have been many methods for producing natural gas from gas hydrate reservoirs in permafrost and sea floor sediments. It is well knownthat the depressurization should be a best option for Class 1 gas hydrate deposit, which is composed of tow layers: hydrate bearing layer and an underlying free gas. However many of gas hydrate reservoirs in sea floor sediments are classified as Class 2 that is composed of gas hydrate layer and mobile water, and Class 3 that is a single gas hydrate layer. The most appropriate production methods among the present methods such as thermal stimulation, inhibitor injection, and controlled oxidation are still under development with considering the gas hydrate reservoir characteristics. In East Sea of Korea, it is presumed that the thick fractured shale deposits could be Class 2 or 3, which is similar to the gas hydrate discovered offshore India. Therefore it is needed to evaluate the possible production methods for economic production of natural gas from gas hydrate reservoir. Here we would like to present the production of natural gas from gas hydrate deposit in East Sea with industrial flue gases from steel company, refineries, and other sources. The existing industrial complex in Gyeongbuk province is not far from gas hydrate reservoir of East Sea, thus the carbon dioxide in flue gas could be used to replace methane in gas hydrate. This approach is attractive due to the suggestion of natural gas productionby use of industrial flue gas, which contribute to the reduction of carbon dioxide emission in industrial complex. As a feasibility study, we did the NMR experiments to study the replacement reaction of carbon dioxide with methane in gas hydrate cages. The in-situ NMR measurement suggeststhat 42% of methane in hydrate cages have been replaced by carbon dioxide and nitrogen in preliminary test. Further studies are presented to evaluate the replacement ratio of methane hydrate at corresponding flue gas concentration.

• 한국분말재료학회지
• /
• 제4권2호
• /
• pp.106-112
• /
• 1997

$Cu-Al_20_3 $ composite powders were prepared by hydrogen reduction of $Cu^{2+}$ from ammoniacal copper sulfate solution on alumina core using autoclave. The copper reduction rate and the properties of copper layer were investigated using Scanning Electron Microscope(SEM), X-ray diffractometer, size and chemical analyzers. The reduction rate of $Cu^{2+}$ showed the maximum value when the molar ratio of [$NH_3$]/[$Cu^{2+}$] was 2. In order to prevent the agglomeration of Cu powder and ethane reduction rate, $Fe^{2+}$ and anthraquinone which act as catalysis were added in the solution. Catalysis was effectively chanced with the addition of two elemerts at a time. Optimum conditions obtained in this study were hydrogen reduction temperature of 205$^{\cire}C$, stirring speed of 500 rpm and hydrogen partial pressure of 300 psi. Obtained $Cu-Al_20_3 $ composite Powders were found to have the uniform and continuous copper coating layer of nodule shape with 3~5 $\mu$m thickness.

• 한국결정성장학회지
• /
• 제22권2호
• /
• pp.84-91
• /
• 2012

Single and few-layer graphene nanosheets (GNs) have successfully synthesized by a modified Hummer's method followed by chemical reduction of exfoliated graphene oxide (GO) in the presence of hydrazine monohydrate. GO and GNs were characterized by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), X-ray diffractions (XRD), Raman spectroscopy, Transmission electron microscopy (TEM), Atomic force microscopy (AFM), Optical microscopy (OM) and by electrical conductivity measurements. The result showed that electrical conductivity of GNs was significantly improved, from $4.2{\times}10^{-4}$ S/m for GO to 12 S/m for GNs, possibly due to the removal of oxygen-containing functional group during chemical reduction. In addition, the $NO_2$ gas sensing characteristics of GNs are also discussed.