• Advances in Energy Research
• /
• 제3권1호
• /
• pp.31-43
• /
• 2015

This paper compares the performance of JP-8(Jet Propellant) fuel and liquefied petroleum gas (LPG) and natural gas in the F110 GE100 jet engine. The cost of natural gas usage in gas turbine engines is lower than JP-8 and LPG. LPG cost is more than JP-8. LPG volume is bigger than JP-8 in the same flight conditions. Fuel tank should be cryogenic for using natural gas in the aircraft. Cost and weight of the cryogenic tanks are bigger. Cryogenic tanks decrease the move capability of the aircraft. The use of jet propellant (JP) is the best in available application for F110 GE 100 jet engine.

• 센서학회지
• /
• 제26권2호
• /
• pp.114-121
• /
• 2017

This paper describes the design and fabrication of a three-axis force sensor with parallel plate beams (PPSs) for measuring the calf force while a patient with a walking assist robot is walking. Current walking assist robots can't measure the weight of the patient's leg and the robot's leg which required for robot control. So, the three-axis force sensor in the calf link is designed and manufactured, it is composed of a Fx force sensor, a Fy force sensor and a Fz force sensor. The three-axis force sensor was designed using by FEM(Finite Element Method), and fabricated using strain-gages. The characteristics experiment of the three-axis force sensor was carried out respectively. The test results indicated that the repeatability error and the non-linearity error of three-axis force sensor was less than 0.04% respectively. Therefore, the fabricated three-axis force sensor in the calf link can be used to measure the patient's calf force in the walking assist robot.

• 한국정밀공학회지
• /
• 제27권1호
• /
• pp.33-40
• /
• 2010

In this research, the effects for surface Improvement of plasma ion implanted carbide endmill tools were observed by measuring cutting forces and tools wear affecting surface roughness in high speed cutting. From the 2nd ion mass analysis, the oxidation layer was found to be built up by sputtering. The residual gas contamination of oxygen was found to be contained impurities in nitrogen gas. The plasma implanted ion was found to be spreaded, especially the nitrogen was implanted up to 150nm depth as impressed voltage and ion implanting time. It is analyzed as bring surface improvement by spreading deeply forming oxidation on surface. The factors in Analysis of Variance(ANOVA) about mutuality cause reference of cutting force. The cutting force Fx is affected by the interaction of spindle rpm and federate, the cutting force Fy is influenced by spindle rpm and time injected ion, and cutting force Fz is affected by the interaction of impressed voltage and feedrate. Also, it was found that the cutting forces of implanted tools become lower and the surface roughness is improved by the effect of nitrogen according to the implantation.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.425-428
• /
• 2006

Natural gas hydrate has been a major problem for its plugging nature in the pipeline. With the demand of deep-water production, the importance of flow assurance technology, preventing hydrate, asphaltene and wax in the pipeline becomes bigger Kinetic models combined with the flow simulator are being developed to explain the nature of hydrate plug formation in the pipeline. To simulate the hydrate plug formation, each stage including the nucleation, growth and agglomeration should be considered. The hydrate nucleation is known to be stochastic and is believed hard to be predicted. Recent publications showed hydrate growth and agglomeration can be observed rigorously using a particle size analyzer. However properties of the hydrate should be investigated to model the growth and agglomeration. The attractive force between hydrate particles, supposed to be the capillary force, was revealed to be stochastic. Alternative way to model the hydrate agglomeration is to simulate by the discrete element method. Those parameters, particle size distribution, attractive force, and growth rate are embedded into the kinetic model which is combined Into the flow simulator. When compared with the flowloop experimental data, hydrate kinetic model combined into a flow simulator showed good results. With the early results, the hydrate kinetic model is promising but needs more efforts to improve it.

• Journal of Welding and Joining
• /
• 제27권1호
• /
• pp.59-64
• /
• 2009

In order to determine the One-Drop One-Pulse(ODOP) condition of the pulsed gas metal arc(GMA) welding, the drop detaching phenomenon during the peak time is investigated using the force-displacement model. The drop detaching criterion is established based on the displacement of the pendant drop, and the forces exerted on the drop are calculated using the Modified Force Balance Model(MFBM). The effects of wire melting on the drop size and force are included in the force-displacement model. While the peak current has most significant effects on the drop detaching time, the initial drop mass prior to the peak time also influences drop transfer. The calculated results show good agreements with the experimental data, which implies that the ODOP condition can be predicted using the force-displacement method.

• 한국생산제조학회지
• /
• 제24권6호
• /
• pp.632-638
• /
• 2015

Many failures have been reported in gas turbine facilities owing to repeated startups and prolonged use of the turbines. In this study, the causes and mechanism of fatigue failure in the first blade of a gas turbine were analyzed using a finite element method to calculate the centrifugal force, bending force, and a modal analysis based on the stress-stiffening effect and harmonic response under the operating conditions. The results show that, fatigue damage was caused by the resonance conditions encountered, in which the first natural frequency declined along with an increase in the metal temperature of the blade. The position of the expected fatigue damage was shown to match the actual position of the cracking at the root area of the blade, which was on the concave side. In addition, the equivalence fatigue stress was observed to approach the fatigue limit.

• Ocean Systems Engineering
• /
• 제6권1호
• /
• pp.99-115
• /
• 2016

In meeting the technical needs for deepwater conditions and overcoming the shortfalls of single-layer pipes for deepwater applications, pipe-in-pipe (PIP) systems have been developed. While, for PIP pipelines directly laid on the seabed or with partial embedment, one of the primary service risks is lateral buckling. The critical axial force is a key factor governing the global lateral buckling response that has been paid much more attention. It is influenced by global imperfections, submerged weight, stiffness, pipe-soil interaction characteristics, et al. In this study, Finite Element Models for imperfect PIP systems are established on the basis of 3D beam element and tube-to-tube element in Abaqus. A parameter study was conducted to investigate the effects of these parameters on the critical axial force and post-buckling forms. These parameters include structural parameters such as imperfections, clearance, and bulkhead spacing, pipe/soil interaction parameter, for instance, axial and lateral friction properties between pipeline and seabed, and load parameter submerged weight. Python as a programming language is been used to realize parametric modeling in Abaqus. Some conclusions are obtained which can provide a guide for the design of PIP pipelines.

• 한국군사과학기술학회지
• /
• 제13권6호
• /
• pp.998-1005
• /
• 2010

Rifling force has a torsion impulse effect on the gun tube and thus generates undesirable vibration of the gun tube about its bore axis, putting additional stress on the projectile. High rifling force at the muzzle of the gun tube may adversely influence the trajectory of the projectile. And, the service life of rifled gun barrels is known to depend on the rifling force. Rifling force along the path of the projectile in the longitudinal direction of the gun tube can be described with projectile mass, projectile velocity, gas pressure curve and rifling angle. Under the same conditions, the character of the rifling of the gun barrel decisively influences the rifling force curve. To reduce the above mentioned harmful effect, locally distinct maximum of rifling force has to be avoided and maximum rifling force needs to be minimized. The best way to minimize the maximum rifling force is to design a rifling angle function so that the rifling force curve has a near trapezoidal shape. In this paper a new approach to make the optimal rifling force curve is described. The rifling angle determining the rifling force is developed by combined Fourier series and polynomial function to satisfy both the convergence and boundary condition matching problems.

• 한국수소및신에너지학회논문집
• /
• 제23권5호
• /
• pp.468-475
• /
• 2012

A proper stacking force and assembly are important to the performance of fuel cell. Improper assembly pressure may lead to leakage of fuels and high interfacial contact resistance, excessive assembly pressure may result in damage to the gas diffusion layer and other components. The pressure distribution of gas diffusion layer is important to make interfacial contact resistance less for stack performance. To analyze the influence of design parameter factors for pressure distribution, and to optimize stack design, DOE (Design of Experiment) was used for polymer electrolyte membrane fuel cell stack pressure test. As commonly known, the higher clamping force improves the fuel cell stack performance. However, non-uniformity of stress distribution is also increased. It shows that optimization between clamping force and stress distribution is needed for well designed structure of fuel cell stack. In this study, stack design optimization method is suggested by using FEM (Finite Element Methode) and DOE for light-weighted fuel cell stack.

• 문화기술의 융합
• /
• 제9권1호
• /
• pp.545-550
• /
• 2023

차량 충돌 시 벨트를 잡아당겨 탑승자의 상해 가능성을 최소화하기 위한 안전장치인 프리텐셔너는 화약 폭발 방식으로 구동되므로 화재나 파편이 튀는 2차 사고의 위험이 있으며 사고 발생 후 프리텐셔너 내부의 가스 발생기 뿐만 아니라 매니폴더를 포함한 연결 부품 모두를 교체해야 하는 단점이 있다. 따라서 본 논문에서는 안전하고 반영구적으로 사용이 가능한 탄성력 기반 프리텐셔너를 제안한다. 기존 프리텐셔너의 작동 원리를 열역학적/동역학적 관점으로 분석한 후 프리텐셔너 전개를 위해 필요한 가스 폭발에너지를 탄성에너지로 변환하였다. 또한 비감쇠 진동해석을 통해 프리텐셔너 작동시간을 확인하였으며 폭발 압력과 전개 시간 조건을 모두 만족하는 스프링 강성을 선정하였다. 스프링 부착 위치에 따른 차량 내부 설치 규격을 고려하여 코일 스프링 형상 및 고정부를 설계하였으며 제작을 통해 탄성력 기반 프리텐셔너의 성능 검증을 수행하였다.