• 한국분무공학회지
• /
• 제10권4호
• /
• pp.32-46
• /
• 2005

The breakup characteristics of liquid sheets formed by the impinging and swirl type injectors were studied as increasing the Weber number (or injection condition) and the ambient gas pressure to 4.0.MPa. In the case of impinging type injector. we compared the changes of breakup lengths between laminar and turbulent sheets. which are formed by the impingement of laminar and turbulent jets. respectively. The results showed that both sheets expand as increasing the injection velocity irrespective of the ambient gas density when the gas based Weber number is low. When the Weber number is high, however, the breakup of turbulent sheet depends on the hydraulic force of jets as well as the aerodynamic force of ambient gas which determines the breakup of laminar sheet. Using the experimental results. we could suggest empirical models on the breakup lengths of laminar and turbulent sheets. In the case of swirl type injector. as $We_l$, and ambient gas density increased, the disturbances on the annular liquid sheet surface were amplified by the increase of the aerodynamic forces. and thus the liquid sheet disintegrated near from the injector exit. Finally, the measured breakup length of swirl type injector according to the ambient gas density and $We_l$, was compared with the result by the linear instability theory. We found that the corrected breakup length relation derived from linear instability theory considering the attenuation of sheet thickness agrees well with our experimental results.

• 한국가시화정보학회지
• /
• 제22권1호
• /
• pp.68-78
• /
• 2024

The stratification phenomena of still hydrogen (20%) and methane (80%) gas mixture in a vertical urban gas pipe have been investigated by simulating the flows based on a mixture model. The stratification is accompanied with the natural convection by the buoyancy force. The hydrogen volume fraction in the upper sections of the pipe increases with time but the increasing rate gets smaller due to the weaker buoyancy force. The pipe with a smaller diameter exhibits a higher peak of hydrogen concentration. The size of vortices is proportional to the pipe diameter. The slip velocity between hydrogen and methane oscillates with a large amplitude at the earlier stage of stratification and then the amplitude decreases sharply. The slip velocity decreases with the diameter, making the stratification become slower. The length of pipe does not affect the stratification since the pipe is sufficiently long relative to the size of vortices.

• 한국가스학회지
• /
• 제22권1호
• /
• pp.1-8
• /
• 2018

수소연료전지 자동차 압력 용기에는 연료전지 스택으로 수소의 흐름을 제어하기 위해 전자 밸브가 부착되고 있다. 전자 밸브의 솔레노이드는 전기 신호에 의해 유로를 개폐하는 역할을 하며, 전원이 인가되는 시간이 경과함에 따라 온도가 상승하여 일정 온도에서 포화된다. 특히 온도의 상승은 솔레노이드의 흡인력을 감소시키므로 안정적인 수소 공급을 위해서 설계 시 포화 온도와 온도에 따른 흡인력 특성 파악이 요구된다. 본 연구에서는 솔레노이드 설계 변수에 따른 포화 온도 계산식을 제안하고 열 유동 해석을 통해 타당성을 확인하였다. 또한, 온도에 따른 흡인력 변화를 분석하기 위해 전자기장 해석을 수행하였으며 온도 특성 실험을 통해 포화 온도와 흡인력 해석 결과를 검증하였다. 포화온도는 계산식과 해석결과를 비교하였을 때 $5.3^{\circ}C$, 해석 결과와 실험 결과를 비교하였을 때 $5.9^{\circ}C$의 오차가 발생하였으며, 흡인력은 1.0 N, 최대 2.1 N의 오차가 발생하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.18-20
• /
• 2002

In this paper, various forces generated in the Gas Circuit Breaker(GCB) such as operating force, repulsive force, spring force, and dashpot force are analyzed with the fluid properties and the mechanical structure. The operation of GCB can be understood. A stroke curve from the result of simulation is compared with experimental one.

• Journal of Advanced Marine Engineering and Technology
• /
• 제6권2호
• /
• pp.69-91
• /
• 1982

The major factors which affect the crankshaft axial vibration are such items as the axial stiffness and mass of crankshaft, the thrust block stiffness, the propeller's entrained water and the exciting and damping forces of engine, propeller and shafting. Among above mentioned items, the axial stiffness and mass of crankshaft, thrust block stiffness and propeller's entrained water were treated in detail in part I, and so in this paper, the rest of above items will be studied. The exciting forces of crankshaft axial vibration are generated mainly from the gas explosion pressure of cylinder, the thrust fluctuation of propeller, and sometimes the torsional vibration of crankshaft induces the crankshaft axial vibration. As for the propeller thrust fluctuation, its harmonic components can be fairly exactly calculated from the experimental results of propeller in the towing tank, but as the calculation process is rather tedious and laborious, the empirical values are ordinarily used. On the other hand, the table of harmonic components of gas pressure has been already published by major slow speed diesel engine makers, but the axial thrust conversion factor of radial force is not unknown yet, and as its estimated value is unreliable, the axial vibration force of gas pressure is uncertain. As the calculation of damping force is very complicated and it includes some uncertain factors, the thoretically estimated amplitudes of axial vibration are much more incorrect in comparison with those of torsional vibrations. Authors have paid special attentions to deriving the theoretical calculation formula of axial conversion factor of radial force and damping force of crankshaft axial vibration and developed a computer program to calculate resonance amplitudes and additional stresses of crankshaft axial vibrations. Also, to check the reliability of the developed computer program, the axial vibrations of three ships' propulsion shaftings were analyzed and their results were compared with those of measured values and makers' results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2327-2332
• /
• 2007

This study investigates on the inhalation force improvements of hood consisted one of the local ventilation systems attached the new device named as gas-guidance-device for removed a pollution source. The numerical method applying finite element method is calculated the velocity and pressure distributions of a moving fluid at the beginning and the inside of a hood with and without the gas-guidance-device in hood. And, the experimental study is measured the wind velocity using the anemometer at the same condition of numerical study. Also, the optimum shape of gas-guidance-device which is suitable for hood shape derived from the numerical and experimental results. The results of this study is supplied the important data to an industrial field for control of a pollution source in the engineering aspect. Moreover, the introduced technique of hood attached the gas-guidance-device is very useful to remove the harmful materials such as dust and waste happened in the manufacturing factory.

• 공업화학
• /
• 제21권4호
• /
• pp.475-478
• /
• 2010

불소화 반응을 통하여 PDMS을 질소 분위기 하에서 $50{\sim}2000\;{\mu}mol/mol$ 농도의 불소 가스($F_2$)를 사용하여 직접적인 방법으로 복합막 표면개질을 하였고 이를 OM (Optical Microscope), AFM (Atomic Force Microscope), SEM (Scanning electron microscope), FT-IR (Fourier transform infrared spectroscopy)을 측정하여 막 표면을 연구하였고 GC (Gas chromatography)로 혼합 노블가스의 기체 거동을 조사하였다. 다양한 노블 혼합 가스를 사용하여 표면 개질된 PDMS 멤브레인의 선택도가 50% 향상 되었다.

• 한국군사과학기술학회지
• /
• 제15권3호
• /
• pp.241-249
• /
• 2012

Performance analysis of the interior ballistics has been conducted using the 1-D numerical code called IBcode according to the various conditions such as length of ignition-gas injector, amount of ignition-gas, mass of projectile, and drag force of projectile. In case of the length of ignition-gas injector, the 25~100 % of the full-injector length has been considered as well as the mass & mass flow of the ignition-gas. The mass of the projectile 5~70 kg and its drag force of 0~69 MPa have been also considered. Variables such as breech & base pressure, negative differential pressure and muzzle velocity for the performance analysis have been sorted, too. Firing conditions for the optimal performance have been investigated through these variables.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.218-219
• /
• 2008

A gas-liquid centrifugal separator is widely used in industry because of its simple geometry and little maintenance. Also, these separators have considerable advantages over filters, scrubbers or precipitators in term of compact design, low pressure drop and higher capacity. A gas-liquid centrifugal separator is a device that utilizes centrifugal force and low pressure to separate liquid from gas by density difference. Design parameters such as length of separation space, swirl vane exit angle, inlet to outlet pipe diameter ratio, models for separation efficiency and low pressure drop as a function of physical dimension are not available in literature. In present study, length of separation space (from vane to gas exit opening) has been studied using CFD. The 3-D Navier-Stokes equations are numerically solved using a fully implicit finite volume scheme. Based upon the obtained solutions, tangential velocities, centrifugal forces, vortices and total pressure losses are analyzed to find the best design parameters.

• 한국자동차공학회논문집
• /
• 제3권6호
• /
• pp.238-249
• /
• 1995

The gas pressure acting on the rings in internal combustion engine influences the friction and wear characteristics. Inter-ring pressure variation during engine operation results from cylinder gas flow through a piston-ring pack. The flow passages consist of ring end gaps and clearances between the ring and the piston groove. The gas flow in the clearance between the ring and the groove is directly affected by the axial motion of the ring in the groove. In this paper the asperity contact force is newly considered in the prediction of the clearence between the ring and the groove surface. This term must be taken into account physically in case that the clearance get narrow rather than asperity height between the ring and the groove surface. Finally, comparisons of calculated inter-ring gas pressures based on the analytical method are made with the measured ones. The agereement was found to be good below midium engine speed, 3000rpm. In order to obtain accurate analytical results to the extend of high rpm range, it is recommended to include oil ring motion as well as top and second ring in analytical model.