• Journal of Industrial and Engineering Chemistry
• /
• 제67권
• /
• pp.333-346
• /
• 2018

This study presents a mathematical modeling approach for developing models based on non-ideal conditions related to the membrane structure including porous supporting layer and deformation under pressure. Comparison of the findings with experimental data reveal the importance of considering the resistance in porous supporting layer though the effect of concentration polarization in the permeate stream could be neglected. Investigations on deformation of fibers under pressure ascertain that at larger fiber inner radius to outer radius ratios, increasing driving force may lead to an initial increase in permeability. After that, the effects of deformation dominates and thus permeability may be decreased.

• 자동차안전학회지
• /
• 제6권1호
• /
• pp.33-40
• /
• 2014

In this study the cylinder liner deformation which is one of the most influencing factors in a diesel engine oil consumption was performed by the finite element analysis on the basic designed structure consisting of the cylinder block, head and liners under the conditions of assembly, thermal and gas loads. Compared with a large number of other cylinder blocks showing remarkable harmonic orders of the liner distortion, results are excellent. Namely. the higher harmonic order amplitudes of the radial liner deformation amount to 1 ~ 2㎛ maximally. The main reason lies in the relatively large wall thickness of the liner which amounts to 8.2% of the bore diameter. Besides, a very stiff and symmetrical cylinder block design in combination with a bolt force introduction approximately 1.5mm below the block top deck have a further share on these results. Therefore excellent low oil consumption can be expected.

• 열처리공학회지
• /
• 제14권3호
• /
• pp.151-154
• /
• 2001

$TiO_2$ thin film has wide application because of its high capacitanca, reflection, and good transmissivity in visible range. $TiO_2$ thin film can be made by thermal deposition method, reactive evaporation method, activated reactive evaporation(ARE) method. In the case of thermal deposition, the oxygen deficiency can occur because the melting point of Ti is very high. While in the case of reactive evaporation, high density $TiO_2$ can not be made, because reactive gas($O_2$) and evaporated material(Ti) are not fully combined, activated reactive evaporation, $TiO_2$ is easily deposited at lower gas pressure compared with reactive evaporation because the ionized reactive gas is made by plasma. Therefore, activated reactive evaporation is very useful to deposit the material having the high melting point. In this work, we formed $TiO_2$ thin film by activated reactive evaporation method. The surface of $TiO_2$ thin film was analyzed by X-ray photoelectron spectroscopy. The surface morphology which was analyzed by atomic force microscopy(AFM) shows that feature of the film surface is uniform. The dielectric capacitance, withstanding voltage were $600{\mu}F/cm^2$, 0.4V respectively. In further work, we can increase the withstanding voltage by improving the deposition parameter of substrates.

• 한국정밀공학회지
• /
• 제14권12호
• /
• pp.153-159
• /
• 1997

A thermally-driven polysilicon microactuator has been fabricated using surface micromachining techniques. It consists of P-doped polysilicon as a structural layer and TEOS(tetraethylorthosilicate) oxide as a sacrificial layer. The polysilicon was annealed for the relaxation of residual stress which is the main cause to its deformation such as bending and buckling. And newly developed HF GPE(gas-phase etching) process was also employed to eliminate the troublesome stiction problem using anhydrous HF gas and CH$_{3}$OH vapor, and successfully fabricated the microactuators. The actuation is incurred by the thermal expansion due to the current flow in the active polysilicon cantilever, which motion is amplified by lever mechanism. The moving distance of polysilicon microactuator was experimentally conformed as large as 21 .mu. m at the input voltage level of 10V and 50Hz square wave. The actuating characteris- tics are also compared with the simulalted results considering heat transfer and thermal expansion in the polysilicon layer. This microactuator technology can be utilized for the fabrication of MEMS (microelectromechanical system) such as microrelay, which requires large displacement or contact force but relatively slow response.

• 한국정밀공학회지
• /
• 제18권8호
• /
• pp.32-39
• /
• 2001

This paper presents the synchronous vibration control of a rotor system using an Active Air Bearing(AAB). In order to suppress the synchronous vibration, it is necessary to actively control the air film pressure or the air film thickness. In this study, active pads are used to control the air film thickness. Active pads are supported by the pivots containing piezoelectric actuators and their radial positions can be actively controlled by applying voltage to the actuators. Disturbances and various kinds of external force can cause the shaft vibration as well as the change of the air film thickness. The dynamic behaviors of a rotary system supported by two tilting-pad gas bearings and its active stabilization using the tilting-pads as actuators are investigated numerically. The PID controller is applied to the tilting-pad gas bearing system with three pads, two of which contain piezoelectric actuators. To test the vapidity of the theoretical method, the performance of this control method is evaluated through experiments. The experimental results show the effectiveness of the control system for suppressing the unbalanced response of the rigid modes.

• 한국추진공학회지
• /
• 제19권4호
• /
• pp.102-109
• /
• 2015

본 연구에서는 가스 터빈 엔진용 고속 베어링 설계의 첫 단계로 엔진 작동 조건에 따른 베어링 하중을 도출한다. 대상 가스터빈 엔진의 베어링에는 공력 하중, 자중, 가속에 따른 관성력이 부여된다. 이에 3-D 공간상에서의 힘 평형 조건과 자이로스코픽 효과를 고려한 모멘트 평형식을 기반으로 베어링에 부가되는 하중을 예측한다. 최종적으로 합동운용규격지침서(Joint Service Specification Guide)에 제시된 엔진 운용 조건으로부터 과도상태 최대, 최소 베어링 하중 조건 및 정상상태 최대, 최소 베어링 하중 조건을 도출한다. 본 연구를 통해 확보된 베어링 하중 조건은 추후 설계 단계인 베어링의 형상 설계와 성능 검증 시험의 경계 조건으로 활용될 것이다.

• 한국압력기기공학회 논문집
• /
• 제5권2호
• /
• pp.20-26
• /
• 2009

The dominant incidents category for onshore and offshore natural gas transmission pipelines in the world is associated with outside forces. Incidents in the outside forces category embrace acts of nature, which typically cause widespread structural damage, as well as act of man, whose effects tend to cause dents and/or gouges localized at point of contact that are referred to as mechanical damage. Therefore, these damage types must be better addressed to avoid unnecessary and costly repairs and the possibility of catastrophic events. First of all, the characterizing features of mechanical damage in gas pipelines were evaluated by using of excavator or boring machine. There is no reliable method for evaluating the safe operating pressure of pipeline affected by mechanical damage. It is especially important to evaluate the remaining strength of damaged pipelines due to outside force. Therefore, the full scale burst tests were conducted to evaluate the remaining strength of pipe with mechanical damage that combines a dent and a gouge. This paper is supposed to provide information that will assist in developing a criterion to assess serviceability in pipelines with mechanical damage.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.347-352
• /
• 2009

공압시스템은 지상설비 및 발사체 공급시스템에 광범위하게 활용되고 있다. 공압시스템의 목적은 수요처에서 요구되는 유량 및 압력을 요구조건에 맞게 공급하는 것이다. 발사체 관련 가스공급은 타 분야 가스공급과는 달리 대유량의 가스공급이 일반적으로 요구되며, 이때 공급압력이 감소되어 유량을 공급하는 동안 요구되는 압력을 만족시키지 못하는 현상이 흔히 발생한다. 공급시 압력감소는 레귤레이터의 특성과 직접적으로 연관되어 있다. 본 논문은 대유량 가스공급시 공급압력 감소와 관련된 레귤레이터의 특성을 제어이론의 측면에서 검토하였고 이를 개선시킬 수 있는 방법을 이론적으로 제시하였다.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.230-231
• /
• 2005

As environmental problems are important, automotive industries are developing various techniques to prevent air pollution. One of these is Positive Crankcase Ventilation (PCV) system. It removes blowby gas which includes about 30% hydrocarbon of total generated quantity. In this system, a PCV valve is attached in a manifold suction tube to control the flow rate of blowby gas which generates differently according to various operating conditions of an automotive engine. As this valve is very important, designers are feeling to design it because of both small size and high velocity. For this reason, we numerically investigated to understand both spool dynamic motion and internal fluid flow characteristics. As the results, spool dynamic characteristics, i.e. displacement, velocity, acting force, increase in direct proportion to the magnitude of differential pressure and indicate periodic oscillating motions. And, the velocity at the orifice region decreases according to the increase of differential pressure because of energy loss which is caused by the sudden decrease of flow area at the orifice region and the increase of flow volume in the front of spool head. Finally, the mass flow rate at the outlet decreases with the increase of spool displacement. We expect that PCV valve designers can easily understand fluid flow inside a PCV valve with our visual information for their help.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.242.2-242.2
• /
• 2014

Plasma-polymer thin films (PPTF) have been deposited on a Si(100) wafer and glass under several conditions such as different RF power by using plasma-enhanced chemical vapor deposition (PECVD) system. Ethylcyclohexane, ammonia gas, hydrogen and argon were utilized as organic precursor, doping gas, bubbler gas and carrier gases, respectively. PPTFs were grown up with RF (ratio frequency using 13.56 MHz) powers in the range of 20~60 watt. PPTFs were characterized by FT-IR (Fourier Transform Infrared), FE-SEM (Scanning Electron Microscope), AFM (Atomic Force Microscope), Contact angle and Probe station. The result of FT-IR measurement showed that the PPTFs have high cross-link density nitrogen doping ratio was also changed with a RF power increasing. AFM and FE-SEM also showed that the PPTFs have smooth surface and thickness. Impedance analyzer was utilized for the measurements of C-V curves having different dielectric constant as RF power.