• Bulletin of the Korean Chemical Society
• /
• 제31권2호
• /
• pp.397-400
• /
• 2010

Zirconium oxide thin films deposited on the p-type Si(100) substrates by radio-frequency (RF) reactive magnetron sputtering with different plasma gas ratios have been studied by using spectroscopic ellipsometry (SE), atomic force microscopy (AFM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The deposition of the films was monitored by the oxygen gas ratio which has been increased from 0 to 80%. We found that the thickness and roughness of the zirconium oxide thin films are relatively constant. The XRD revealed that the deposited thin films have polycrystalline phases, Zr(101) and monoclinic $ZrO_2$ ($\bar{1}31$). The XPS result showed that the oxidation states of zirconium suboxides were changed to zirconia form with increasing $O_2$ gas ratio.

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권5호
• /
• pp.617-623
• /
• 2003

In the present study, the characteristics of upward bubble flow were experimentally investigated in a liquid bath. The velocity of upward bubble flow was calculated for two different experimental conditions：1) bubble flow without kinetic energy 2) bubble flow with kinetic energy. Bubble flow without kinetic energy starts to undergo the effect of buoyancy l0cm away from the nozzle. Whereas. kinetic energy is dominant before 30 cm away from the nozzle in bubble flow but after this point kinetic energy and inertial force are applied on bubble flow at the same time In addition, as the flow rate increases the maximum velocity point moves to the nozzle. The velocity Profiles near free surface is extremely irregular due to surface flow. Gas volume fraction is high near the nozzle due to gas concentration. but decreases with the increasement of axial position. Gas volume fraction does not vary after the axial position, z=60 in spite of the increasement of flow.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권1호
• /
• pp.1-7
• /
• 2016

The influence of boundary condition of the bodies with gas flows is one of the most important problems in high-altitude aerodynamics. In this paper presents the results of the calculation of aerodynamic characteristics of aerospace vehicle using Monte-Carlo method based on three different gas-surface interaction models - Maxwell model, Cercignani-Lampis-Lord (CLL) model and Lennard-Jones (LJ) potential. These models are very sensitive for force and moment coefficients of aerospace vehicle in the hypersonic free molecular flow. The models, method and results can be used for new generation aerospace vehicle design.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.242.2-242.2
• /
• 2011

Molecularly imprinted polymer thin films were applied to develop a gas sensor based on the surface plasmon resonance phenomenon for small gaseous molecules such as toluene and xylene. The imprinted polymer films were synthesized via photo-polymerization method using various combination of templates, functional monomers and cross-linkers. The temperature of pre-polymerization solutions and the power of UV light were controlled for optimized performance of gas sensing. The morphology and porosity of the polymer films were controlled by varying the mixing ratios of the pre-polymerization solutions and confirmed by atomic force microscopy. By fitting the adsorption/desorption sensorgrams to conventional kinetic models, the effects of different templates and cross-linkers were interpreted in term of the structural differences of the polymer networks formed on the gold film. The sensitivity and selectivity of sensors were estimated for toluene and xylene, and also for humidity and other gaseous molecules such as formaldehyde and ammonia.

• 천문학회보
• /
• 제42권2호
• /
• pp.56.1-56.1
• /
• 2017

The distribution of gas on cosmological scales is vital to our understanding of galaxy formation. Using the RAMSES cosmological hydrodynamical simulation code we have explored the evolution of the gas properties in a cosmological volume. We have identified the effect of the maximum simulation force resolution, and the resolution of the initial conditions, on the gas density power spectrum, as well as artefacts due to the RAMSES algorithm. The RAMSES methodology can add spurious power on small scales, particularly in low resolution simulations. This effect can be expected to have a strong impact on the results of RAMSES simulations, because this additional power appears at specific epochs, implying a sudden change to the system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.785-790
• /
• 2000

The resonant frequency of a gas-filled cylindrical Helmholtz resonator in a liquid is obtained analytically. The equation of motion of the resonator is derived by using the condition of equilibrium of forces acting on the mass in the neck of the resonator. The reaction force on the upper side of the cylinder due to the acceleration of external fluid and sound radiation is obtained by using the analytical results for the baffled circular-piston problem. From the frequency response function of the resonator, a formula to predict the resonant frequency of the resonator is derived. It is shown that the resonant frequency of the Helmholtz resonator significantly decreases due to the cushioning effect of gas inside the cavity. Therefore, when a pressure transducer is to be installed in a pin-hole type mounting method, much care should be paid to remove the gas from the cavity.

• 한국유체기계학회 논문집
• /
• 제5권2호
• /
• pp.43-49
• /
• 2002

In this paper, the steady-state performances analysis of a tilting pad gas bearing(TPGB) we analyzed by using finite element method for compressible Reynolds' equation. TPGB is used in a high-expansion-ratio expander running at a speed of 230,000 rpm. In order to solve the nonlinear finite element equations, the Newton-Raphson method is applied. The variations of the loading capacity, friction force and tilting angle of a single pad v.s. eccentricity direction of eccentricity and bearing number are investigated. The condition for the equilibrium of a pad, which is important for safe working of the bearing, is stated. The performances of the three pad bearing such as loading capacity, friction moment are predicted.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.775-780
• /
• 2004

CWR technology is generally believed to contribute to the increase of train speed and bring a variety of significant advantages, such as the decrease in track works, noise and vibration as well as the improvement of passenger comfort. In CWR technology, welding is considered to be one of the most important element technologies. Among the various welding methods, gas pressure welding is the most frequently used in vicinity of train line station since the operation is simple and the instruments are not heavy. The gas pressure welding is constructed exactly by good manual book on which simple and excellent welding methods is written and has the same performance as raw material. But this can be poor in the variety of the processing of rail end surface to be welded, the control of oxyacetylene flame and axil compressive force. This study tries to describe the characteristics of gas pressure welding, defect-causing factors and preventive counterplan of defects

• Nuclear Engineering and Technology
• /
• 제51권7호
• /
• pp.1866-1870
• /
• 2019

Residual salt separation is an essential step in pyroprocessing because its reaction products, as prepared by electrochemical unit processes, contain frozen residual electrolyte species, which are generally composed of alkali-metal chloride salts (e.g., LiCl, KCl). In this study, a simple technique that utilizes high-temperature gas flux as a driving force to melt and push out the residual salt in the reaction products was developed. This technique is simple as it only requires the use of a heating gun in combination with a gas injection system. Consequently, $LiNO_3-ZrO_2$ and $LiCl-ZrO_2$ mixtures were successfully separated by the high-temperature gas injection (separation efficiency > 93%), thereby demonstrating the viability of this simple technique for residual salt separation.

• 한국토양비료학회지
• /
• 제36권5호
• /
• pp.263-271
• /
• 2003

$CO_2$ 가스 존재여부와 pH가 Pb(II)와 sodium dodecyl sulfonate(SDS, $C_{12}H_{25}SO_3Na$) 흡착에 따른 silca 표면의 특성 변화에 미치는 영향을 contact angle 과 AFM을 이용한 힘 측정을 통하여 살펴보았다. 대기와 접촉하여 $CO_2$가 용해되는 조건에서 Pb와 SDS가 $10^{-4}M$ 씩 들어 있는 혼합용액을 처리하였을 때, fused silica 표면의 contact angle은 $PbCO_3$의 침전 때문에 최대 $46^{\circ}$로 낮았다. 반면에 $N_2$ 개스를 불어넣는 $CO_2$ 부재조건에서는 $PbCO_3$의 침전이 없었기 때문에 contact angle이 최대 $90^{\circ}$로 크게 증가되었다. $CO_2$ 부재조건에서 pH에 따른 contact angle과 AFM에서 측정한 점착력($F_{ad}$) 변화 양상은 $PbOH^+$ 화학종 분포와 유사하였으므로, Pb(II)의 silica 표면 흡착형태는 $PbOH^+$ 로 판단되었다. 한편 contact angle 과 AFM 측정결과 모두 Pb 단독처리에서 소수성을 발현하였다. 이 결과는 현재까지의 알려진 이론으로 설명할 수 없었으며 이를 위하여 원자수준에서의 심도 깊은 연구가 필요하다고 판단되었다.