• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.9
• /
• pp.669-676
• /
• 2013

In this study, we introduce a polymer(polyimide) based pressure sensor to measure real-time heart beat and blood pressure. The sensor have been designed with consideration of skin compatibility of material, cost effectiveness, manufacturability and wireless detection. The designed sensor was composed of inductor coils and an air-gap capacitor which generate self-resonant frequency when electrical source is applied on the system. The sensor was obtained with metalization, etching, photolithography, polymer adhesive bonding and laser cutting. The fabricated sensor was shaped in circular type with 10mm diameter and 0.45 mm thickness to fit radial artery. Resonant frequencies of the fabricated sensors were in the range of 91~96 MHz on 760 mmHg pressurized environment. Also the sensor has good linearity without any pressure-frequency hysteresis. Sensitivity of the sensor was 145.5 kHz/mmHg and accuracy was less than 2 mmHg. Real-time heart beat measurement was executed with a developed hand-held measurement system. Possibility of real-time blood pressure measurement was showed with simulated artery system. After installation of the sensor on skin above radial artery, simple real blood pressure measurement was performed with 64 mmHg blood pressure variation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.9
• /
• pp.912-918
• /
• 2011

In this paper, a composite right-/left-handed(CRLH) rectangular waveguide satisfying a balanced condition above the cut-off frequency is presented. The proposed structure consists of one shorted stub and two twisted H-plane irises which produce an effectively negative permeability and permittivity, respectively. The CRLH structure can independently control the series and shunt resonance frequencies of a CRLH transmission line which determine the left-handed(LH) and right-handed(RH) bands due to a minimized coupling between a shorted stub and twisted H-plane irises. Thus, the design of the CRLH waveguide satisfying a balanced condition is possible. To analyze the CRLH structure, a crossly connected equivalent circuit is derived. The simulated and measured results confirm that the proposed CRLH waveguide has a transmission property without a band gap among the LH and RH bands.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.10
• /
• pp.458-463
• /
• 2003

In order to develope piezoelectric transformer for the ballast of fluorescent lamp, a new shape and electrode pattern of piezoelectric transformer has been investigated in this work. The composition of piezoelectric ceramics was 0.95Pb(Zr$_{0.51}$Ti$_{0.49}$)O$_3$+0.03Pb(Mn$_{1}$3/Nb$_{2}$3/)O$_3$+0.02Pb(Sb$_{1}$2/Nb$_{1}$2/)O$_3$. The sample prepared by this composition system showed the characteristics which has about 1200 of relative dielecric constant, 1100 of the mechanical quality factor, 0.53 of the electromechanical coupling coefficient, 320 pC/N of the piezoelectric constant d$_{33}$, 0.3 % of the dissipation factor. Diameter and thickness of disk-type piezoelectric transformer was 45 mm and 4 mm, respectively. The driving and generating electrode with their gap of 1mm were fabricated on the top surface. But the common electrode was fabricated on the whole bottom surface. The electrode surface ratio of driving and generating part on the top surface ranges from 1.4:1 to 3:1. We investigated the electrical characteristics with the variation of the electrode surface ratio of driving and generating part in the range of load resistance of 100 $\Omega$～70 k$\Omega$. The set-up voltage ratio of this piezoelectric transformer increases with increasing both the electrode surface of driving part and the load resistance. The set-up voltage ratio at no load resistance was more than 60 times. On the other hand, the efficiency decreases with increasing the electrode surface of driving part. In the case of the electrode surface of both 1.4:1 and 2:1, maximum efficiency showed above 97 % at load resistance of 2 k$\Omega$. However, in the case of the electrode surface of 3:1, maximum efficiency showed about 94 % at load resistance of 3 k$\Omega$.>.>.>.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.473-482
• /
• 1998

In this paper, characteristics of the wide band microstrip antennas with parasistic element are analyzed by the Finite Difference Time Domain(FDTD) method, and antenna parameters are optimized to get maximum bandwidth, retern loss, input impedance, and radiation pattern are calculated by Founier transforming the time domain results. The characteristics of the antenna are varied and the bandwidth of the antenna is broaded as a length and a width of the driven element, a gap of the driven element and the parasitic element, a width and a length of parasitic element. So the different patchs are resonating at different frequencies and this multipule resonance increase the bandwidth. The Results of the calculation and measurement, the size of the antenna with parasitic element is about a twice larger than a microstrip antenna, but bandwidth is four times better than a microstrip antenna. And these results were in relatively good accordance with the measured values.

• Journal of electromagnetic engineering and science
• /
• v.11 no.3
• /
• pp.166-173
• /
• 2011

In this paper, we implemented and analyzed a wireless power transfer (WPT) system with a CSPR topology. CSPR refers to constant current source, series resonance circuit topology of a transmitting coil, parallel resonance circuit topology of a receiving coil, and pure resistive loading. The transmitting coil is coupled by a magnetic field to the receiving coil without wire. Although the electromotive force (emf) is small (about 4.5V), the voltage on load resistor is 148V, because a parallel resonance scheme was adopted for the receiving coil. The implemented WPT system is designed to be able to transfer up to 1 kW power and can operate a LED TV. Before the implementation, the EMF reduction mechanism based on the use of ferrite and a metal shield box was confirmed by an EM simulation and we found that the EMF can be suppressed dramatically by using this shield. The operating frequency of the implemented WPT system is 30.7kHz and the air gap between two coils is 150mm. The power transferred to the load resistor is 147W and the real power transfer efficiency is 66.4 %.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.12
• /
• pp.171-176
• /
• 2005

This study designed and fabricated a multi-purpose planar antenna for base stations that are accessible to DCS, WiBro, and ISM. The proposed antenna was designed into an open loop form from the existing monopole structure. The capacitance of the multi-purpose antenna was increased by the coupling of open parts. This makes the use of MMIC and LTCC convenient and the antenna is smaller and has a larger gain than existing antennas. The resonance distance and bandwidth can be adjusted by changing the open gap and the height of the loop of the antenna. The bandwidth of the designed antenna satisfies DCS, IMT-2000, WiBro, Bluetooth, wireless LAN and ISM bands based on VSWR 2. The entire frequency bandwidth is $58.75\%$ of $1.575GHz\~2.985GHz(1.41GHz)$. Also, the radiation pattern of the antenna displayed co-polarization and cross-polarization characteristics at 1.6GHz, 2.3GHz and 2.8GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.5 s.120
• /
• pp.547-552
• /
• 2007

In this paper, the coupled microstrip lines of hairpin type are applied to design a compact microstrip ring hybrid. When the gap decreases, three attenuation poles are created by coupling between the lines. The proposed structure can achieve a significant reduction of size and suppression of the harmonics. And it has the same frequency responses of conventional ring hybrid at 2.55 GHz. The harmonics are suppressed to below -20 dB up to 12 GHz, including the third harmonic. The ring part size of the proposed ring hybrid is reduced to one forth of the conventional ring hybrid. The measured frequency responses agree well with simulated ones.

• Polymer(Korea)
• /
• v.37 no.6
• /
• pp.736-743
• /
• 2013

Novel carbazole based copolymers were synthesized by Suzuki coupling polymerization. (Diphenylene)vinylene and n-octyl was introduced to carbazole as pendants for reducing band gap and improving solubility, respectively. Thermal, photoluminescence and electro-luminescence of copolymers were studied for applying the emitting layer of polymer light emitting diode (PLED). Maximum UV-vis absorption and photoluminescence (PL) emission wavelength of copolymers showed 333~340 nm and 409~464 nm in solution state, respectively. The relative quantum yield using 9,10-diphenylanthracene as a reference was 25.8%. These copolymers exhibited high thermal stability ($T_d$ = $350^{\circ}C$) and good film forming ability. Good luminance was obtained at voltages lower than 8 V and the onset voltage was observed at 4.0 V.

• Journal of Power Electronics
• /
• v.19 no.5
• /
• pp.1303-1314
• /
• 2019

This paper studies the harmonic characteristics of ship electric propulsion systems and their treatment methods. It also adopts effective measures to suppress and prevent ship power systems from affecting ship operation due to the serious damage caused by harmonics. Firstly, the harmonic characteristics of a ship electric propulsion system are reviewed and discussed. Secondly, aiming at problems such as resonant frequency and filter characteristics variations, resonance point migration, and unstable filtering performances in conventional passive filters, a method for fully tuning of a passive dynamic tunable filter (PDTF) is proposed to realize harmonic suppression. Thirdly, to address the problems of the uncontrollable inductance L of traditional air gap iron core reactors and the harmonics of power electronic impedance converters (PEICs), this paper proposes an electromagnetic coupling reactor with impedance transformation and harmonic suppression characteristics (ECRITHS), with the internal filter (IF) designed to suppress the harmonics generated by PEICs. The ECRITHS is characterized by both harmonic suppression and impedance change. Fourthly, the ECRITHS is investigated. This investigation includes the harmonic suppression characteristics and impedance transformation characteristics of the ECRITHS at the fundamental frequency, which shows the good performance of the ECRITHS. Simulation and experimental evaluations of the PDTF are carried out. Multiple PDTFs can be configured to realize multi-order simultaneous dynamic filtering, and can effectively eliminate the current harmonics of ship electric propulsion systems. This is done to reduce the total harmonic distortion (THD) of the supply currents to well below the 5% limit imposed by the IEEE-519 standard. The PDTF also can eliminate harmonic currents in different geographic places by using a low voltage distribution system. Finally, a detailed discussion is presented, with challenges and future implications discussed. The research results are intended to effectively eliminate the harmonics of ship electric power propulsion systems and to improve the power quality of ship power systems. This is of theoretical and practical significance for improving the power quality and power savings of ship power systems.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.1
• /
• pp.55-59
• /
• 2022

In this paper, we compared the electric field and absorptance of nano particles in nanostructures by amplifying the electric field around the nanoparticles through plasmon resonance and comparing the structure that can increase the absorptance with the nanostructure by using the Finite Different Time Domain (FDTD) simulation. In addition, the width of the nanostructure was adjusted to 240 nm ~ 300 nm, and the light absorptance rate was higher as the gap between the particles was short. In addition, a study was conducted on the formation of nanoparticles and nanostructures on the surface through UV imprint. In order to form particles in the structure, the nano particles were first arranged in the mold used for the fabrication of the structure using spray coating, and then fabricated through UV imprinting. The nanostructure and particles were formed together by scanning electron microscopy.