• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1439-1443
• /
• 2007

In this paper, vibration reduction techniques of a voice coil motor (VCM) actuator are presented for AFM imaging system. The damping coefficient of the actuator driven by VCM with a flexure hinge is quite low and it cause the about 30dB peak amplitude response at the resonance frequency. To decrease this peak response, we design and apply elliptical band-stop filters to xy and z axis VCM actuator. Frequency response of each actuator with filter is measured to verify the effect of the filters. As a sensor, capacitive sensor is used. Vibration reduction rate of the xy actuator with the filter is also measured while real AFM scanning condition. As another method, closed loop control with the capacitive sensor is applied to the xy axis actuator to add an electrical damping effect and vibration reduction rate measured. These vibration reduction rates with each method are compared. In the case of z axis actuator, the frequency response of force (gap) control loop is measured. For comparison, the frequency response using a conventional PID controller is also obtained. Finally, the AFM image of a standard grid sample is measured with the designed controller to analyze the effect in the AFM imaging.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.466-469
• /
• 1995

This paper presents a design and performance of the 6 D.O.F linear motion table with a magnetic bearing suspension. The linear positioning of the table with a 150mm stroke is driven by a brushless DC Linear motor and the other attitudes of the stage are controlled by the analog PD controller with magnetic bearing actuators. Each magnetic bearing unit which consists of 3 electromagnets, 3 capacitance probes and 3 backup bearings affords controlled forces by detecting the air gap between the probes and guideways. An integral type capacitance probe amplifier is equipped on the upper plate of the table so that the probe line to the probe amplifier can be shorter therefore the problems due to the stray capacitance and noise can be reduced. Form the pitch-yaw errormeasured by the autocollimator, the vertical and horizont straightness errors of the table are derived that they are maintained below 1.mu. m over 100mm stroke. The positioning accuracy of the linear motion is maintained below 2 .mu. m and the repeatability error is below 1 .mu. m

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.6
• /
• pp.8-14
• /
• 2005

Understanding of the flow past a bluff body close to a moving ground is very important in automobile and aeronautical fields because of aerodynamic characteristic and instability induced by unsteady vortex shedding. The passive control method that mounted the vertical and horizontal plates at the lower surface of the cylinder is studied to suppress the unsteady oscillation motion. When the grounds moves, the diminish of the shear layer on the ground promotes the interaction between the lower and the upper separated shear layers of the cylinder, hence vortex shedding occurs at the lower gap height than the stationary ground.

• Journal of the Korea Society for Simulation
• /
• v.15 no.3
• /
• pp.61-67
• /
• 2006

This paper provides a systematic way of integrating human intelligence and autonomous precision of robots to achieve the highest possible performance of a cooperating robot system. Adjustable autonomy, which deals with the combination of human and robotic skills, has the potential to bridge the gap which leaves many tasks suited to robotics beyond the reach of existing technology. Especially we will show that relevant human assistance or intervention will increase system performance by improving the exception handling capability, simplifying autonomous operation, and boosting speed and reliability. To support the usefulness of our scheme, a series of experiments were conducted with three cooperating robots which work together to dock both ends of a long suspended beam into stanchions.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.7
• /
• pp.753-759
• /
• 2009

As many systems depend on electronics in an intelligent vehicle, concern for fault tolerance is growing rapidly. For example, a car with its braking controlled by electronics and no mechanical linkage from brake pedal to calipers of front tires(brake-by-wire system) should be fault tolerant because a failure can come without any warning and its effect is devastating. In general, fault tolerance is usually designed by placing redundant components that duplicate the functions of the original module. In this way a fault can be isolated, and safe operation is guaranteed by replacing the faulty module with its redundant and normal module within a predefined interval. In order to make in-vehicle network fault tolerant, this paper presents the concept and design methodology of an IEEE 1451 based dual CAN module. In addition, feasibility of the dual CAN network was evaluated by implementing the dual CAN module.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.4
• /
• pp.391-395
• /
• 2010

In our paper, we propose an asymmetric single-tracked wheel system, and describe its structure and the method for maintaining the length of a transformable track system. And the method is reducing the gap of lengths. Therefore, we propose an efficient structure for transforming and explain motions with kinematics. Our transformable shape single-tracked mobile system has an advantage to overcome an obstacle or stairs by the variable arms in the single unity track system. But we will make the variable shape of tracked system get a drive that has a force to stand against a wall. In this case, we can consider this system to a rigid body and have a notice that this single tracked system is able to get vary shape with the variable arm angle. Considering forces balance along x-axis and y-axis, and moments balance around the center of the mass we have. If this rigid body is standing against a wall and doesn't put in motion, the force of flat ground and the rigid body sets an equal by a friction. In the same way, the force of a wall and the rigid sets an equal by a friction.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.12
• /
• pp.10-17
• /
• 2009

Nano-Electro-Mechanical MOSFET (NEMFET) using Double-Gate MOSFET (DGMOS) structure can efficiently control the short channel effect. Espatially, subthreshold current of depletion-mode Double-Gate NEMFET (Dep-DGNEMFET) decreases in the off-state due to the thin equivalent-oxide thickness. Analytical $t_gap$ vs. $V_g$ equation for Dep-DGNEMFET is derived and characteristics for different device structures are analyzed. Dep-DGNEMFET structure is optimized to satisfy ITRS criteria.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.10
• /
• pp.1018-1023
• /
• 2010

The CAN (Controller Area Network) system is the most dominant protocol for in-vehicle networking system because it provides bounded transmission delay among ECUs (Electronic Control Units) at data rates between 125Kbps and 1Mbps. And, many automotive companies have chosen the CAN protocol for their in-vehicle networking system such as chassis network system because of its excellent communication characteristics. However, the increasing number of ECUs and the need for more intelligent functions such as ADASs (Advanced Driver Assistance Systems) or IVISs (In-Vehicle Information Systems) require a network with more network capacity and the real-time QoS (Quality-of-Service). As one approach to enhancing the network capacity of a CAN system, this paper introduces a CAN system with dual communication channel. And, this paper presents a distributed message allocation method that allocates messages to the more appropriate channel using forecast traffic of each channel. Finally, an experimental testbed using commercial off-the-shelf microcontrollers with two CAN protocol controllers was used to demonstrate the feasibility of the CAN system with dual communication channel using the distributed message allocation method.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1057-1058
• /
• 2008

철도차량용 선형추진시스템에 있어서, 지상레일에 설치되는 선형유도전동기의 2차측의 리액션플레이트의 시공 공차에 의해서 발생되는 1차측과의 공극의 변화는 추진 시스템의 운행 시 승차감과 기기효율을 떨어뜨리는 결과를 초래하기 때문에 선형유도전동기의 균일 공극 운전은 추진 시스템의 효율을 증가시킬 수 있는 중요한 사항이다. 또한 경사구간에서의 선형유도전동기의 공극길이 조절을 통해서 선형유도 전동기의 용량 변경 없이 추력을 증가시키는 것이 가능하다. 따라서 본 논문에서는 선형유도전동기의 공극 길이를 제어할 수 있으며, 공극 길이제어를 통하여 추진 시스템의 성능 변화를 살펴볼 수 있는 축소 모델선형유도전동기 성능시험기의 공극조절 시스템의 동적 모델링 및 특성 해석을 통하여 시스템을 구성하는 파라미터들의 특성 변화 분석 및 시스템 구현 가능성에 대한 연구를 수행하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.2
• /
• pp.119-125
• /
• 2001

This paper presents an experimental study on active control of self-excited vibration for a high speed turbomachinery. In order to suppress the self-excited vibration, it is necessary to actively control the air film pressure or the air film thickness. In this study, active pads are used to control the air film thickness. Active pads are supported by pivots containing piezoelectric actuators and their radial position can be actively controlled by applying voltage to the actuators. The transfer characteristics from actuator inputs to shaft vibration outputs are experimentally investigated. In a tilting-pad gas bearing (TPGB), a shaft is supported by the pressurized air film. Four gap sensors were used to measure the vibration of the shaft and PID was used in the feedback control of the shaft vibration. The experimental results show that the self-excited vibration of the rotor can be effectively suppressed if the PID controller gains are properly chosen. As a result we find that the feedback control is effective for suppressing the self-excited vibration of a rotor system using stack-type PZT actuators.