• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.652-656
• /
• 2002

The HDM(Hole Drilling Method) is a relatively simple and accurate method in measuring residual stress of welded metal. Various methods of evaluating residual stress are studied in welding field. The method of cutting holes on the plate much affects the accuracy of result. Especially for the hard material like stainless steel difficult to cut preciously is difficult to measure residual stress on welded metal. Because heat conduction of stainless steel is lower than other general steel, the magnitude of residual stress might be different as to changing of welding conditions. Therefore, The distribution of residual stress on the STS304 steel after welding using HDM is evaluated in this paper.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.155-161
• /
• 2001

Currently knowledge of strain in welds has mainly been obtained from strain gaging method; that is directly attaching most of the material to the gage. The very few non-contact method are still in the early stage. One of the non-contact methods is by the use of the laser that has high-level of the accuracy for the measurement, and this laser also has excellent characteristics on which many studies for its applications are focused throughout the many fields. The dissertation is on the measurement of the strain caused by the characteristics and the temperature changes of the TIG welded zone which is used with 3D ESPI system that is functionally modified through the laser ESPI system. This system employed the aluminum sheet-metal which are mainly used for the steel plate such as for the electronics, chemistry, food instrument and electronic appliances.

• 한국생산제조학회지
• /
• 제5권3호
• /
• pp.31-39
• /
• 1996

The objective of this study is to investigate the influence of welding residual stresses on the fatigue crack growth behavior of cracks located transverse to the weld bead. For this purpose, G. T. A (Gas Tungsten Arc) welding was performed on hte Al alloy 1100-O plate and the same initial crack is made on HAZ(Heat Affected Zone), weld metal and base meta respectively. Specimens were used CT(Compact Tension) specimens. Initial welding residual stresses were measured by using strai gage sectioning method. All specimens were tested under constant amplitude load with stress ratio R=0.1, It is possible to predict fatigue crack growth behaviors and the fatigue life, using numerical analysis together with distribution of initial residual stress and the values of C and m obtained from $da/dN-{\Delta}K$

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1996년도 춘계학술대회 논문집
• /
• pp.177-182
• /
• 1996

The objective of this thesis is to investigate the influence of welding residual stresses on the fatigue growth behavior of welding residual stresses on the fatigue growth behavior of cracks located transverse to the weld bead. For this purpose, G.T.A. (Gas Tungsten Arc) welding was performed on the Al. Alloy 1100-0 plate and the same initial crack is made on HAZ(Heat Affected Zone), weld metal and base metal respectively. C.T.(Compact Tension) specimens were used as experimental material. Initial welding residual stresses were measured by using strain gage sectioning method. All specimens were tested under constant amplitude load with stress ratio R=0.1

• 한국항공우주학회지
• /
• 제30권2호
• /
• pp.46-51
• /
• 2002

홀 확장법은 홀 주위에 압축 잔류응력 층을 생성시킴으로서 균열 발생을 지연시키는 방법으로 항공산업 분야에서 널리 사용되고 있다. 홀 확장잔류응력의 분포는 홀 확장률, 맨드럴 삽입방향, 재료 물성치 등 여러 가지 홀 확장 파라미터에 따라 달리진다. 홀 확장 잔류응력 층의 정확한 파악이 항공사업의 실제 설계에 있어서 매우 중요함에도 불구하고 이에 대한 연구는 상대적으로 부족하였다. 본 연구에서는 3차원 유한요소해석을 통하여 알루미늄 평판에 홀 확장법을 적용하는 경우의 잔류응력 분포를 예측하고자 하였다. 유한요소해석의 타당성을 검증하기 위하여 스트레인 게이지를 이용한 홀 확장 잔류변형률을 측정하였으며, 홀 확장률과 2단 홀 확장이 잔류응력 분포에 미치는 영향을 파악하였다. 2단 홀 확장을 적용함으로써 최대 압축 잔류응력의 크기가 약 7% 향상됨을 알 수 있었다.

• 한국정밀공학회지
• /
• 제18권2호
• /
• pp.214-221
• /
• 2001

This paper describes the design of 3-component force/moment sensor with the force and moment ratio of wide range. It can measure the x-direction force Fx, y-direction force Fy and z-direction moment Mz simultaneously. In order to accurately measure forces and moment using 3-component force/moment sensor, it should get suitable force and moment ratio(the ratio of force Fx=200 N and moment Mz=20 Nm is ten to one), and small interference error. In this paper, in order to design the 3-component force/moment sensor with the force and moment ratio of wide range, the procedures are performed as follow : 1) the derivation of the equations to predict the bending strains on the surfaces of the plate-beams under the force or the moments, 2) the determination of the size of the sensing elements of the force/moment sensor by using the derived equations, 3) the Finite Element Method(FEM) analysis and the characteristic test for confirming the strains from the theory analysis, 4) the selection of the attachment locations of the strain gages of each sensor, 5) the analysis of the rated strain and the interference error at the attachment location of strain gages. It reveals that the rated strains calculated from the derived equations make a good agreement with the results from the Finite Element Method analysis and the characteristic test.

• 한국추진공학회지
• /
• 제11권6호
• /
• pp.42-49
• /
• 2007

본 연구에서는 마이크로 추진장치의 개발을 위한 기초연구로 마이크로 노즐의 유동 특성을 분석하였다. 냉가스 추진원리를 이용하였으며, 추진 장치의 노즐 목 직경이 1.0, 0.5, 0.25 mm 인 마이크로 노즐을 방전가공을 이용하여 제작하였다. 판스프링과 스트레인 게이지를 이용한 추력측정장치를 이용하여 추력을 측정하였으며, 대기압 환경과 진공환경에서 마이크로 노즐의 유동특성을 분석하였다. 추진제는 아르곤과 질소를 사용하였으며, 실험 결과를 CFD 결과와 비교하였다. 연구 결과 노즐의 소형화로 인해 점성과 배압에 의한 유동손실이 발생함을 확인할 수 있었다.

• 센서학회지
• /
• 제26권2호
• /
• pp.114-121
• /
• 2017

This paper describes the design and fabrication of a three-axis force sensor with parallel plate beams (PPSs) for measuring the calf force while a patient with a walking assist robot is walking. Current walking assist robots can't measure the weight of the patient's leg and the robot's leg which required for robot control. So, the three-axis force sensor in the calf link is designed and manufactured, it is composed of a Fx force sensor, a Fy force sensor and a Fz force sensor. The three-axis force sensor was designed using by FEM(Finite Element Method), and fabricated using strain-gages. The characteristics experiment of the three-axis force sensor was carried out respectively. The test results indicated that the repeatability error and the non-linearity error of three-axis force sensor was less than 0.04% respectively. Therefore, the fabricated three-axis force sensor in the calf link can be used to measure the patient's calf force in the walking assist robot.

• 대한기계학회논문집A
• /
• 제32권7호
• /
• pp.597-601
• /
• 2008

Currently knowledge of strain in welds has mainly been obtained from strain gaging method: that is directly attaching most of the material to the gage. The very few non-contact methods are still in the early stage. One of the non-contact methods is by the use of the laser that has high-level of the accuracy for the measurement, and this laser also has excellent characteristics on which many studies for its applications are focused throughout the many fields. A method of study is on the measurement of the strain caused by the characteristics of the spot welded zone which is used with 3-D ESPI system that is functionally modified through the laser ESPI(Electronic Speckle Pattern Interferometry) system. This system employed the SGCC 1.2t which are mainly used for the steel plate such as automobile, structure, building material and electronic appliances.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1521-1524
• /
• 2003

Currently the plates used for the various structures has a tendency to being slim to the degree of the sheet metal vis-a-vis the overall measurements of the structure, and the conditions of their usage and load have been getting diverse. As the structure material has been used more and more under the various conditions, the necessity of the strength analysis is to be required. While most of these methods are simply based on the strain gaging method; that is, directly attaching most of the material to the gage, using the non-contact method is still in the early stage. One of the non-contact methods is by the use of the laser that has high-level of the accuracy for the measurement, and this laser also has excellent characteristics on which many studies for its applications are focused throughout the many fields. Therefore, this dissertation is on the measurement of the strain caused by the characteristics of the TIG welded zone which is used with 3D ESPI system that is functionally modified through the laser ESPI system.