• Korean Journal of Materials Research
• /
• v.9 no.10
• /
• pp.1012-1017
• /
• 1999

Low resistance ohmic contacts to the Si-doped $\textrm{In}_{0.17}\textrm{Ga}_{0.83}\textrm{N}$(~$\times10^{19}\textrm{cm}^{-3}$) were obtained using the W metallization schemes. Specific contact resistance decreased with increasing annealing temperature. The lowest resistance is obtained after a nitrogen ambient annealing at $950^{\circ}C$ for 90 s, which results in a specific contact resistance of $2.75\times10^{-8}\Omega\textrm{cm}^{-3}$. Interfacial reactions and surface are analyzed using x-ray diffraction and scanning electron microscopy (SEM). The X-ray diffraction results show that the reactions between the W film and the $\textrm{In}_{0.17}\textrm{Ga}_{0.83}\textrm{N}$ produce a $\beta$-$W_2N$ phase at the interface. The SEM result shows that the morphology of the contacts is stable up to a temperature as high as $850^{\circ}C$. Possible mechanisms are proposed to describe the annealing temperature dependence of the specific contact resistance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.422-422
• /
• 2012

투명전극 산화막은 태양전지, 평판 디스플레이 등의 투명전극과 같은 광전자 소자에 사용되고 있다. 투명 전도성 산화막으로서 ITO (Indium tin oxide)는 높은 투과도, 낮은 비저항, 높은 일함수 등의 장점을 가지고 있어서 그동안 널리 사용되어 왔다. 그러나 In의 희소성으로 인한 고가격 문제 때문에 이를 대체하기 위해 불순물을 도핑한 ZnO (Zinc oxide)에 관한 연구가 활발히 진행되어 왔다. ZnO의 전기전도도를 높이기 위해 일반적으로 Al, Ga, B와 같은 3족 원소가 ZnO의 n형 도펀트로 널리 사용된다. 그 중에서 Al은 반응성이 커서 박막 증착 중에 산화되기 쉬운 반면 낮은 생산단가, 우수한 전기적 및 광학적 특성을 보이기 때문에 투명 전극으로서 Al-doped ZnO (AZO)가 많이 이용되고 있다. 본 연구에서는 rf 마그네트론 스퍼터링 공정을 이용하여 glass 기판 위에 Al-doped ZnO (AZO) 투명 전도막을 증착하였고, 수명 및 신뢰성에 영향에 미치는 주요 인자로서 온도, 온도 사이클 및 습도에 따른 AZO 박막의 열화 특성에 대한 연구를 진행하였다. 또한, 온도 사이클, 고온 및 고온고습 환경에 장시간 노출된 AZO 박막들의 성능 저하 원인들을 미세구조 관찰, 전기적 및 광학적 특성 변화들을 연계하여 규명하고자 하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.7
• /
• pp.589-593
• /
• 2005

The electronic states of ZnO doped with Al, Ga and In, which belong to III family elements in periodic table, were calculated using the density functional theory. In this study, the calculation was performed by two Programs; the discrete variational Xa (DV-Xa) method, which is a sort of molecular orbital full potential method; Vienna Ab-initio Simulation Package (VASP), which is a sort of pseudo potential method. The fundamental mixed orbital structure in each energy level near the Fermi level was investigated with simple model using DV-Xa. The optimized crystal structures calculated by VASP were compared to the measured structures. The density of state and the energy levels of dopant elements were shown and discussed in association with properties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.17-18
• /
• 2008

In this paper, 1%-nitrogen doped Nickel was used for improvement of thermal stability of Ni-Germanide. Proposed Ni-N(1%)/TiN structure has shown better thermal stability, sheet resistance and less agglomeration characteristic than pure Ni/TiN structure. During the germanidation process, it is believed that the nitrogen atoms in the deposited nickel layer can suppress the agglomeration of Ni germanide by retarding the diffusion of Ni atoms toward silicon layer, hence improve the thermal stability of Ni-germanide.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.11
• /
• pp.1000-1004
• /
• 2006

In this paper, thermal stability of Ni-silicide formed on the SOI substrate with $B_{11}$ has been characterized. The sheet resistance of Ni-silicide on un-doped SOI and $B_{11}$ implanted bulk substrate was increased after the post-silicidation annealing at $700^{\circ}C$ for 30 min. However, in case of $B_{11}$ implanted SOI substrate, the sheet resistance showed stable characteristics after the post-silicidation annealing up to $700^{\circ}C$ for 30 min. The main reason of the excellent property of $B_{11}$ sample is believed to be the retardation of Ni diffusion by the boron and bottom oxide layer of SOI. Therefore, retardation of Ni diffusion is highly desirable lot high performance Ni silicide technology.

• Korean Journal of Materials Research
• /
• v.31 no.12
• /
• pp.727-731
• /
• 2021

In this study, we have investigated a selective emitter using a UV laser on BBr₃ diffusion doping layer. The selective emitter has two regions of high and low doping concentration alternatively and this structure can remove the disadvantages of homogeneous emitter doping. The selective emitters were fabricated by using UV laser of 355 nm on the homogeneous emitters which were formed on n-type Si by BBr₃ diffusion in the furnace and the heavy boron doping regions were formed on the laser regions. In the optimized laser doping process, we are able to achieve a highly concentrated emitter with a surface resistance of up to 43 Ω/□ from 105 ± 6 Ω/□ borosilicate glass (BSG) layer on Si. In order to compare the characteristics and confirm the passivation effect, the annealing is performed after Al₂O₃ deposition using an ALD. After the annealing, the selective emitter shows a better effect than the high concentration doped emitter and a level equivalent to that of the low concentration doped emitter.

• Journal of the Korean Ceramic Society
• /
• v.39 no.10
• /
• pp.935-942
• /
• 2002

Gallium-doped ZnO (GZO) films were deposited on soda-lime glass substrate without heating using Ne, Ar, or Kr gas. Electrical properties of GZO films deposited at various total gas pressures were investigated for the film positions corresponding to the erosion region (region B) and outside the erosion region (region A) of the target. Region B showed high resistivity, which was attributed to the decrease in carrier density and Hall mobility, compared to region A. GZO films deposited using Ne gas showed the degradation in resistivity and crystallinity, whereas, GZO films deposited using Kr gas showed the improvement in resistivity and crystallinity. This degradation in film properties could be attributed to the film damage caused by the bombardment of high-energy particles. Especially, the energies of recoiled neutral atoms ($Ne^0,\;Ar^0,\;Kr^0$) calculated by Monte Carlo simulation corresponded to experimental results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.5
• /
• pp.291-294
• /
• 2015

Recently, ZnO based oxide TFTs used in the flexible and transparent display devices are widely studied. To apply to OLED display switching devices, electrical performance and stability are important issues. In this study, to improve these electrical properties, we fabricated TFTs having Al doped Zinc Oxide (AZO) layer inserted between the gate insulator and ZnO layer. The AZO and ZnO layers are deposited by Atomic layer deposition (ALD) method. I-V transfer characteristics and stability of the suggested devices are investigated under the positive gate bias condition while the channel defects are also analyzed by the photoluminescence spectrum. The TFTs with AZO layer show lower threshold voltage ($V_{th}$) and superior sub-threshold slop. In the case of $V_{th}$ shift after positive gate bias stress, the stability is also better than that of ZnO channel TFTs. This improvement is thought to be caused by the reduced defect density in AZO/ZnO stack devices, which can be confirmed by the photoluminescence spectrum analysis results where the defect related deep level emission of AZO is lower than that of ZnO layer.

• Journal of the Korean Ceramic Society
• /
• v.48 no.4
• /
• pp.328-333
• /
• 2011

The influence of Al-doped ZnO (AZO) thin films degraded under high temperature and damp heat on the performance deterioration of Cu(In,Ga)$Se_2$ (CIGS) solar cells was investigated. CIGS solar cells with AZO/CdS/CIGS/Mo structure were prepared on glass substrate and exposed to high temperature ($85^{\circ}C$) and damp heat ($85^{\circ}C$/85% RH) for 1000 h. As-prepared CIGS solar cells had 64.91% in fill factor (FF) and 12.04% in conversion efficiency. After exposed to high temperature, CIGS solar cell had 59.14% in FF and 9.78% in efficiency, while after exposed to damp heat, it had 54.00% in FF and 8.78% in efficiency. AZO thin films in the deteriorated CIGS solar cells showed increases in resistivity up to 3.1 times and 4.4 times compared to their initial resistivity after 1000 h of high temperature and damp heat exposure, respectively. These results can be explained by the decreases in carrier concentration and mobility due to diffusion or adsorption of oxygen and moisture in AZO thin films. It can be inferred that decreases in FF and conversion efficiency were caused by an increase in series resistance, which resulted from an increase in resistivity of AZO thin films degraded under high temperature and damp heat.

• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.781-786
• /
• 2000

An Er-doped sulfide fiber was drawn, and its spectroscopic properties were analyzed. Compositions of a 1000 ppmwt Er3+-doped core and an undoped clad were Ge30-Ga1-Asg-S61 and Ge30-As8-S62, in at.%, respectively. Refractive index of the core composition was approximately 0.01 high than that of the clad. In order to enhance the mechanical stability as well as to prevent infiltration of impurity ions such as OH-, an UV-curable polymer was used for the coating. The optical loss of a fiber formed directly from a polymer coated core rod without cladding was ∼15 dB/m at 1.06$\mu\textrm{m}$. In the case of a fiber with core/clad structure, the optical loss was so high that the stimulated emission of erbium fluorescence was not evident. It is believed that presence of inhomogeneous core/clad interface and crystalline aggregates precipitated in the clad region were responsible for the high optical loss. On the other hand, fluorescence characteristics of Er3+ embedded in the core region were more or loss deteriorate compared to fiber preform, which is attributed to the redistribution of the Er ions along with the partial crystallization of the core glass during the fiberization process.