• Journal of Navigation and Port Research
• /
• v.27 no.4
• /
• pp.443-447
• /
• 2003

In this work. using 0.2 GaAs modulation doped FET(MODFET), a high performance DBS downconverter MMIC was developed for direct broadcasting satellite (DBS) application. Without LNA, the downconverter MMIC showed a very low noise of 4.8 dB, which is lower by 3 dB than conventional ones. A low LO power of -10 dBm was required for the normal DBS operation of the downconverter MMIC. which reduced the power consumption via a removal of LO amplifier on MMIC. It required only a low power consumption of 175 mW, which is lower than 70 percent of conventional ones. The LO leakage power at IF output was suppressed to a lower level than 30 dBm, which removes a bulky LO rejection filter on a board. The fabricated chip, which include a mixer, If amplifiers. LO rejection filter, and active balun, exhibited a small size of $0.84{\times}0.9\textrm{mm}^2$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.4
• /
• pp.109-116
• /
• 2024

β-Ga₂O₃ is a representative ultra-wide bandgap (UWBG) semiconductor that has attracted much attention for power device applications due to its wide-bandgap of 4.9 eV and high-breakdown voltage of 8 MV/cm. In addition, because solution growth is possible, it has advantages such as fast growth rate and lower production cost compared to SiC and GaN [1-2]. In this study, we have successfully grown Si-doped 10 mm thick Si-doped β-Ga₂O₃ single crystals by the EFG (Edge-defined Film-fed Growth) method. The growth direction and growth principal plane were set to [010] / (010), respectively, and the growth speed was 7~20 mm/h. The as-grown β-Ga₂O₃ single crystal was cut into various crystal planes (001, 100, ${\bar{2}}01$) and off-angles (1^o, 3^o, 4^o), and then surface processed. After processed, the homoepitaxial layer was grown on the epi-ready substrate using the HVPE (Halide vapor phase epitaxy) method. The processed samples and the epi-layer grown samples were analyzed by XRD, AFM, OM, and Etching to compare the surface properties according to the crystal plane and off-angle.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.6
• /
• pp.1393-1398
• /
• 2015

In this study, the electrical and optical properties of GZO (Ga-doped ZnO) thin films prepared on PES substrates by RF magnetron sputtering method with various working pressures (5 to 20 mTorr) were investigated. All GZO thin films exhibited c-axis preferential growth regardless of working pressure, the GZO thin film deposited at 5 mTorr showed the most excellent crystallinity having 0.44˚ of FWHM. In AFM observations, surface roughness exhibited the lowest value of 0.20 nm in a thin film produced by the working pressure 5 mTorr. Figure of merits of GZO thin film deposited at 5 mTorr showed the highest value of 6652, in this case resistivity and average transmittance in the visible light region were 6.93×10^-4Ω-cm and 81.4%, respectively. We could observed the Burstein-Moss effect that carrier concentration decrease with the increase of working pressure and thus the energy band gap is narrowed.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.6
• /
• pp.321-323
• /
• 2013

100 nm thick Ga doped ZnO (GZO) thin films were deposited with DC and RF magnetron sputtering at room temperature on glass substrate and Al coated glass substrate, respectively. and the effect of the Al underlayer on the optical and electrical properties of the GZO films was investigated. As-deposited GZO single layer films had an optical transmittance of 80% in the visible wavelength region, and sheet resistance of 1,516 ${\Omega}/{\Box}$, while the optical and electrical properties of GZO/Al bi-layered films were influenced by the thickness of the Al buffer layer. GZO films with 2 nm thick Al film show a lower sheet resistance of 990 ${\Omega}/{\Box}$, and an optical transmittance of 78%. Based on the figure of merit (FOM), it can be concluded that the thin Al buffer layer effectively increases the performance of GZO films as a transparent and conducting electrode without intentional substrate heating or a post deposition annealing process.

• Journal of the Optical Society of Korea
• /
• v.20 no.1
• /
• pp.130-134
• /
• 2016

The influence of Au/Ni-based contact formed on a lightly-doped (7.3×1017cm−3, Zn-doped) InGaAsP layer for electrical compensation of surface plasmon polariton (SPP) propagation under various rapid thermal annealing (RTA) conditions has been studied. The active control of SPP propagation is realized by electrically pumping the InGaAsP multiple quantum wells (MQWs) beneath the metal planar waveguide. The metal planar film acts as the electric contact layer and SPP waveguide, simultaneously. The RTA process can lower the metal-semiconductor electric contact resistance. Nevertheless, it inevitably increases the contact interface morphological roughness, which is detrimental to SPP propagation. Based on this dilemma, in this work we focus on studying the influence of RTA conditions on electrical control of SPPs. The experimental results indicate that there is obvious degradation of electrical pumping compensation for SPP propagation loss in the devices annealed at 400℃ compared to those with no annealing treatment. With increasing annealing duration time, more significant degradation of the active performance is observed even under sufficient current injection. When the annealing temperature is set at 400℃ and the duration time approaches 60s, the SPP propagation is nearly no longer supported as the waveguide surface morphology is severely changed. It seems that eutectic mixture stemming from the RTA process significantly increases the metal film roughness and interferes with the SPP signal propagation.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.59-59
• /
• 2010

ZnO는 II-VI 족 화합물 반도체로써 상온에서 큰 엑시톤 결합에너지 (~60 meV) 를 가지며 밴드갭이 3.37 eV인 직접 천이형 반도체로 잘 알려진 물질이다. 이러한 ZnO의 물리적 특성은 광학소자로 상용화된 GaN와 유사하기 때문에 LED나 LD등의 광 소자 재료로 주목 받고 있다. 또한 ZnO는 3족 원소 (In, Ga, Al)를 도핑 함으로써 전기적 특성 제어가 가능한 장점을 가지고 있다. 본 연구는 펄스레이저 증착법 (Pulsed Laser Deposition)을 이용하여 Si (111) 기판 위에 ZnO:In 박막을 성장 시켰으며, 도핑된 indium 양에 따른 ZnO 박막의 배향성 변화를 관찰 하였다. X-선 회절 분석법 (X-ray diffraction), 탐침형 원자현미경 (Atomic Force Microscope) 그리고 투과전자 현미경 (Transmission Electron Microscope)을 측정하였다. XRD 측정 결과 un-doped ZnO 박막은 (002) 방향으로 c-축 우선성장 하였다. 그러나 ZnO 박막내의 Indium 양이 증가 할수록 (002) 방향에서 (101), (102), (103) 등의 (101) 방향으로 성장이 변화 하였으며 5 at.% 이상에서는 (100) 방향의 성장이 관찰 되었다. TEM 측정 결과 un-doped ZnO 박막은 columnar 구조로 성장 되었으나, Indium 양이 증가할수록 column의 size가 감소하며, 5 at.% 이상에서 columnar 구조 성장이 거의 관찰되지 않는다. AFM 결과에서는 Indium 양이 증가 할수록 박막의 표면거칠기와 결정립 크기가 감소하였다.

• Journal of Adhesion and Interface
• /
• v.14 no.1
• /
• pp.28-35
• /
• 2013

In this study, we produced heat-shield coating materials using surface-treated Ga-doped ZnO (GZO) and investigated the dispersity of particle, visible light transmittance, ultraviolet light cut off, infrared light cut-off, heat-shielding property by surface-treating compounds and treatment conditions. In the case of using IPA or acryl binder for heat-shield coating, the dispersity of inorganic oxide particles was poor but in the case of using surface-treated inorganic oxide particles by hybrid compound having urethane (urea) group, acryl group and silica, dispersity of particle, visible light transmittance and haze were improved. We used the measurement kit and sunlamp for measuring heat-shielding property and confirmed that the internal temperature of the measurement kit using heat-shield film was lower more than $4.8^{\circ}C$ in comparison with using PET film for itself.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.1
• /
• pp.1-7
• /
• 2024

β-Ga₂O₃ is a material with a wide band gap of ~4.8 eV and a high breakdown-voltage of 8 MV/cm, and is attracting much attention in the field of power device applications. In addition, compared to representative WBG semiconductor materials such as SiC, GaN and Diamond, it has the advantage of enabling single crystal growth with high growth rate and low manufacturing cost [1-4]. In this study, we succeeded in growing a 10 mm thick β-Ga₂O₃ single crystal doped with 0.3 mol% SnO₂ through the EFG (Edge-defined Film-fed Growth) method using multi-slit structure. The growth direction and growth plane were set to [010]/(010), respectively, and the growth speed was about 12 mm/h. The grown β-Ga₂O₃ single crystal was cut into various crystal planes (010, 001, 100, ${\bar{2}}01$) and surface processed. The processed samples were compared for characteristics according to crystal plane through analysis such as XRD, UV/VIS/NIR/Spec., Mercury Probe, AFM and Etching. This research is expected to contribute to the development of power semiconductor technology in high-voltage and high-temperature applications, and selecting a substrate with better characteristics will play an important role in improving device performance and reliability.

• New Physics: Sae Mulli
• /
• v.68 no.12
• /
• pp.1308-1314
• /
• 2018

$Er^{3+}$ and $Yb^{3+}$ co-doped $Y_3Ga_5O_{12}$ polycrystalline powders were prepared by using a solid-state reaction method, and their crystallinities were measured using X-ray diffraction. According to the results of X-ray diffraction, the powders showed a polycrystalline tetragonal structure. The photoluminescence and the upconversion luminescence properties of the $(Y_{0.85-x}Yb_{0.15})_3Ga_5O_{12}:Er^{3+}_x$ (x = 0.03, 0.06, 0.09, 0.12 and 0.15) phosphors were investigated in detail. Green and red upconversion emissions were observed for the phosphors excited by 980 nm radiation from a semiconductor laser. The powders exhibited strong green and weak red upconversion emission peaks at 553 and 660 nm, respectively. Also, their upconversion processes were explained using an energy-diagram analysis and the strongest upconversion intensity was emitted by the powder with a 0.12 mol $Er^{3+}$ ion concentration.

• Current Photovoltaic Research
• /
• v.8 no.3
• /
• pp.102-106
• /
• 2020

In this paper, the effect of MoSe₂ on the contact resistance (R_C) of the transparent conducting oxide (TCO) and Mo junction in the scribed P2 region of the Cu(In,Ga)Se₂ (CIGS) solar module was analyzed. The CIGS/Mo junction becomes ohmic-contact by MoSe₂, so the formation of the MoSe₂ layer is essential. However, the CIGS solar module has a TCO/MoSe₂/Mo junction in the P2 region due to structural differences from the cell. The contact resistance (R_C) of the P2 region was calculated using the transmission line method, and MoSe₂ was confirmed to increase R_C of the TCO/Mo junction. B doped ZnO (BZO) was used as TCO, and when BZO/MoSe₂ junction was formed, conduction band offset (CBO) of 0.6 eV was generated due to the difference in their electron affinities. It is expected that this CBO acts as a carrier transport barrier that disturbs the flow of current, resulting in increased R_C. In order to reduce the R_C caused by CBO, MoSe₂ must be made thin in a CIGS solar module.