• Structural Engineering and Mechanics
• /
• 제89권6호
• /
• pp.589-599
• /
• 2024

This study presents the usability of the high-rate single-frequency Precise Point Positioning (SF-PPP) technique based on 20 Hz Global Positioning Systems (GPS)-only observations in detecting dynamic motions. SF-PPP solutions were obtained from post-mission and real-time GNSS corrections. These include the International GNSS Service (IGS)-Final, IGS real-time (RT), real-time MADOCA (Multi-GNSS Advanced Demonstration tool for Orbit and Clock Analysis), and real-time products from the Australian/New Zealand satellite-based augmentation systems (SBAS, known as SouthPAN). SF-PPP results were compared with LVDT (Linear Variable Differential Transformer) sensor and single-frequency relative positioning (SF-RP) solutions. The findings show that the SF-PPP technique successfully detects the harmonic motions, and the real-time products-based PPP solutions were as accurate as the final post-mission products. In the frequency domain, all GNSS-based methods evaluated in this contribution correctly detect the dominant frequency of short-term harmonic oscillations, while the differences in the amplitude values corresponding to the peak frequency do not exceed 1.1 mm. However, evaluations in the time domain show that SF-PPP needs high-pass filtering to detect accurate displacement since SF-PPP solutions include trends and low-frequency fluctuations, mainly due to atmospheric effects. Findings obtained in the time domain indicate that final, real-time, and MADOCA-based PPP results capture short-term dynamic behaviors with an accuracy ranging from 3.4 mm to 8.5 mm, and SBAS-based PPP solutions have several times higher RMSE values compared to other methods. However, after high-pass filtering, the accuracies obtained from PPP methods decreased to a few mm. The outcomes demonstrate the potential of the high-rate SF-PPP method to reliably monitor structural and earthquake-induced ground motions and vibration frequencies of structures.

• 방송공학회논문지
• /
• 제19권4호
• /
• pp.439-452
• /
• 2014

본 논문에서는 지상파 DMB 단일 주파수 망(SFN) 설계에서 GPS를 기준 시각으로 모든 사이트의 송출 동기를 일치시키는 기존의 운용방식과 병행하여, 각 사이트의 지형적 특징을 반영한 송신 offset delay를 추가 적용함으로써 동일한 송신 제원으로 기존 대비 서비스 영역을 확장시키는 방법을 연구하였다. 실험결과 미약한 수신 전계강도 지역에서 송신 offset delay가 수신 신호품질을 개선시켰으며 방송 통신위원회가 권고하는 최소 수신 전계강도($45dB{\mu}V/m$) 지점을 기준으로 4~8 km 서비스 영역이 확장됨을 확인하였다. 각 사이트 별 고유한 송신 offset delay를 계산하기 위해서 서비스 영역 내 지리적 특징, 인접 사이트 간 전계강도 분포, 그리고 사이트별 서비스 목표 영역 등 여러 사항을 고려하였으며 본 연구에 대한 검증 실험은 수도권 DMB 서비스 영역으로 한정하였다. 또한 산출된 송신 offset delay가 단일 주파수망에 미치는 영향을 분석하기위해 수신 전계강도와 delay 간의 상관관계를 실험을 통해 분석함으로써, 송신 offset delay의 적용이 서비스 영역을 얼마나 확장시킬 수 있는지 확인하였다.

• 한국통신학회논문지
• /
• 제34권11A호
• /
• pp.882-890
• /
• 2009

본 논문에서는 Loran 신호를 이용하여 원거리통신망 및 전력 분배망과 같은 국가 기반 산업에 대한 망동기를 이루고자 할 때에 Loran 수신기에서 수신한 신호에 대한 위상 동기를 잃어 버렸을 때 이를 보상하기 위한 방안에 대해서 논한다. Loran 수신기에서 위상 동기를 잃었을 때에는 수신기 내에 있는 오실레이터가 자유구동을 하게되고, 따라서 이를 기준으로 출력되는 타이밍 동기신호의 성능이 크게 떨어지게 되며, 이때에 ITU G.811 표준에서 요구하는 PRC에 대한 1 us 이하의 요구 성능을 만족시킬 수 없게 된다. 따라서 본 논문에서는 Loran 수신기가 위상 동기를 잃었을 때 이를 보상하기 위해 보상 알고리즘을 사용하여 위상 점프를 보상하는 방법에 대해 제안했으며, 이에 대해 실측한 데이터에 대한 MTIE 성능을 분석하였다. 성능 분석 결과 제안된 방법을 사용하면 1시간 간격으로 동기를 잃었을 경우에 30 분 평균 이하의 스무딩 값을 사용할 경우 대략 0.6 us 이하의 MTIE 값을 보여서 산업체 표준에서 요구하는 1 us 이내의 PRC 성능을 충분히 만족시킬 수 있음을 확인하였다.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2006년도 International Symposium on GPS/GNSS Vol.2
• /
• pp.385-390
• /
• 2006

This paper examines the sampling and jitter specifications and considerations for Global Navigation Satellite Systems (GNSS) software receivers. Software radio (SWR) technologies are being used in the implementation of communication receivers in general and GNSS receivers in particular. With the advent of new GPS signals, and a range of new Galileo and GLONASS signals soon becoming available, GNSS is an application where SWR and software-defined radio (SDR) are likely to have an impact. The sampling process is critical for SWR receivers, where it occurs as close to the antenna as possible. One way to achieve this is by BandPass Sampling (BPS), which is an undersampling technique that exploits aliasing to perform downconversion. BPS enables removal of the IF stage in the radio receiver. The sampling frequency is a very important factor since it influences both receiver performance and implementation efficiency. However, the design of BPS can result in degradation of Signal-to-Noise Ratio (SNR) due to the out-of-band noise being aliased. Important to the specification of both the ADC and its clocking Phase- Locked Loop (PLL) is jitter. Contributing to the system jitter are the aperture jitter of the sample-and-hold switch at the input of ADC and the sampling-clock jitter. Aperture jitter effects have usually been modeled as additive noise, based on a sinusoidal input signal, and limits the achievable Signal-to-Noise Ratio (SNR). Jitter in the sampled signal has several sources: phase noise in the Voltage-Controlled Oscillator (VCO) within the sampling PLL, jitter introduced by variations in the period of the frequency divider used in the sampling PLL and cross-talk from the lock line running parallel to signal lines. Jitter in the sampling process directly acts to degrade the noise floor and selectivity of receiver. Choosing an appropriate VCO for a SWR system is not as simple as finding one with right oscillator frequency. Similarly, it is important to specify the right jitter performance for the ADC. In this paper, the allowable sampling frequencies are calculated and analyzed for the multiple frequency BPS software radio GNSS receivers. The SNR degradation due to jitter in a BPSK system is calculated and required jitter standard deviation allowable for each GNSS band of interest is evaluated. Furthermore, in this paper we have investigated the sources of jitter and a basic jitter budget is calculated that could assist in the design of multiple frequency SWR GNSS receivers. We examine different ADCs and PLLs available in the market and compare known performance with the calculated budget. The results obtained are therefore directly applicable to SWR GNSS receiver design.