• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.12
• /
• pp.1048-1054
• /
• 2012

This paper presents a Carrier phase fault detection (FD) method for GPS RTK (Global Positioning System Real Time Kinematic) in dynamic environment. There are various error sources in dynamic environment and these errors decrease the reliability of FD results. Due to the reason, Carrier phase measurements are separated into satellite induced signal, user induced signal and other remaining errors. Especially the user-induced signal is computed by user dynamic which is estimated by time-differenced Carrier phase (TDCP) and Doppler shift. TDCP makes it possible to avoid integer ambiguity resolution. Computer simulation is conducted to verify the suggested method. By applying impulse, step and ramp faults, the FD performance is analyzed.

• Journal of the Korea Convergence Society
• /
• v.10 no.11
• /
• pp.327-333
• /
• 2019

The Fuel-cut driving is started when the acceleration pedal released with transmission gear engaged. Fuel economy of the vehicle improves by active fuel-cut driving. A deep-learning technique is proposed to predict fuel-cut driving with vehicle speed, acceleration and road gradient data in the study. It's 3~10 of hidden layers and 10~20 of variables and is applied to the 9600 data obtained in the test driving of a vehicle in the road of 12km. Its accuracy is about 84.5% with 10 variables, 7 hidden layers and Relu as activation function. Its error is regarded from the fact that the change rate of input data is higher than the rate of fuel consumption data. Therefore the accuracy can be better by the normalizing process of input data. It's unnecessary to get the signal of vehicle injector or OBD, and a deep-learning technique applied to the data to be got easily, like GPS. It can contribute to eco-drive for the computing time small.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.19 no.2
• /
• pp.155-161
• /
• 2001

When determining a three dimensional position for engineering purposes, we can use the GPS survey to find position. According to the enhancement of precision for domestic Geoid model, the positional accuracy of GPS about precise method of vertical position has been also increased. But by considering Geoid undulation, it is difficult to measure GPS-derived elevations. Because Geoid undulation has changed little in local sites, GPS-derived elevations are similar to orthometric height. By ignoring Geoid undulation, it is possible to measure GLT-derived elevations at the local. small construction sites. GLT(GPS Leveling Technique) provides a method for computing orthometric heights. GLT processes the data more rapidly than conventional measurement devices. We only considered the weight factors affecting accuracy between the points. That is, the GPS procedures to produce satisfactory elevation accuracy depends on the method of observations, receivers and conditions of the local environment. A comparison was performed between the GPS survey using Geoid model and GLT at a part within Pusan National University and construction model sites in South Korea. And the writers proved the GPS surveying is efficient in positioning accuracy, time, and cost on a construction sites.

• Journal of Korean Society of Disaster and Security
• /
• v.13 no.2
• /
• pp.65-75
• /
• 2020

The efficiency of sewage treatment was ananlyzed selecting a sewage treatment plant in Gyeonggi-do where A₂O process was applied. Statistical techniques based on the operation data of the sewage treatment were used. The main factors directly affecting the efficiency of the treatment process were analyzed using a GPS-X model. The correlation analysis and one-way ANOVA were performed. The T-N and NH₄⁺-N values of the effluent did not generate statistically significant level (p-value:>0.05) when compared with C/N ration values. Removel of nitrogen components form sewage treatment plants were affected by temperature, HRT, SRT and DO. In the case of BOD, all operating factors were affected, while COD was affecte by factors of HRT, STR and DO. In simulations using GPS-X, the parameters that greatly influence was included the maximum sedimentation rate, the dependent nutrient microbial yield (anoxic), the phosphorus saturation coefficient, the dependent nutrient microbial killing rate, the dependent nutrient microbial maximum growth rate, and the independent trophic microorganisms. The maximum growth rate and the maximum setting rate were identified.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.9
• /
• pp.907-913
• /
• 2010

In this paper, we have described a development of the external instrumentation system of a fighter aircraft for flight test. The external instrumentation system consists of the instrumentation pod and the image pod. The instrumentation pod measures a flight data(attitude, velocity, altitude, etc) of the fighter aircraft by using GPS/AHRS sensor. The image pod takes high-speed images for the separation trajectory of a smart bomb with 2 high-speed cameras and video signal for it with one general camera. We have verified the performance of the external instrumentation system through the ground test, the environment test and the flight test.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.3
• /
• pp.565-571
• /
• 2016

This study check the construction site and borrow pit location using GIS-based Open Global Map. Construction Equipment (Dump, Grader) utilizes the GPS (Global Positioning System) to gain equipment's real-time position, speed, altitude, using the data such as directions to perform real-time monitoring. The analysis of the productivity is completed through using the data, and the optimal number of equipment is calculated. It was found that the analysis results showed approximately 30% less cost compared to the actual design plan.

• Bulletin of the Korean Space Science Society
• /
• 2010.04a
• /
• pp.29.2-29.2
• /
• 2010

항법분야에 있어서 위성항법시스템의 다양한 오차를 제거한 정밀한 위치 정보를 이용하여 이동체에 활용하는 연구가 진행되고 있다. 실제 환경에서 이동체를 이용한 항법실험을 수행하기 전 실제 환경과 유사한 가상의 실시간 테스트베드를 구축하여 알고리즘 테스트 및 검증 실험을 수행하려 한다. 이를 위해 이동체의 운동을 시뮬레이션하는 운동궤적제어시스템과 실제의 항법신호를 시뮬레이션하는 GNSS 시뮬레이터 사이의 시각동기화는 실시간 시뮬레이션을 구현하기 위해 필수적으로 요구된다. 동기화 되지 않은 시각정보는 이동체 운동궤적제어시스템에 의해 생성된 실제의 궤적과 GNSS 시물레이터로부터 생성된 궤적사이의 오차를 유발하여 항법수신기의 부정확한 항법신호를 유발한다. 이 연구는 GNSS 시뮬레이터를 이용한 실시간 테스트베드의 구축에 있어 필요한 이동체 운동궤적의 시각동기화 기술 개발을 목표로 한다. GNSS 시뮬레이터는 Spirent 사의 GPS 시뮬레이터가 사용되었다. 이동체의 위치, 속도, 가속도와 같은 움직임을 나타내는 운동에 관한 명령은 적용되어야 하는 정확한 시각이 함께 전송되므로, 이는 그 시각 이전에 GPS 시뮬레이터에 도달해야 한다. 따라서 1초(1 Hz) 또는 0.1초(10 Hz) 사이에 원격제어시스템과 GPS 시뮬레이터사이의 시각 동기화를 구현하였다. 시뮬레이터와의 시각정보 동기화를 위해 Amplicon사의 PCI-215 타이머카드를 이용하였고, 그 결과, 이동체 운동궤적제어시스템과 시뮬레이터의 시각정보를 $10^{-3}$ 내의 위치오차를 가지는 정밀도로 동기화됨을 확인할 수 있었다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.90-93
• /
• 2010

Lately, increasing utilization of vehicle blackbox, there is acted research and development of blackbox. But, currently used Blackbox was stored only video, sound and have Limit to know details of an accident. When disappeared mounted blackbox inside the vehicle, there don't know information of blackbox. In this paper, because using video and sound and GPS, blackbox store current location and route and vehicle speed, blackbox increase efficiency and accuracy of accident analysis. and using wareless LAN, smart blackbox implement to transfer external store media.

• Journal of Advanced Navigation Technology
• /
• v.11 no.3
• /
• pp.239-251
• /
• 2007

This thesis is about the reduction of the power consumption in GPS embedded terminals with periodic position fix to improve the time delay of position determination. In order to improve time delay of position determination during the wireless terminal is powered on, it needs to be set such that it can be periodically recalibrated by the GPS and those recalibrated values need to be saved in the terminal's memory so that it can reduce the time delay from the request of location. By using the trace of the information that's been saved in the terminal's memory, it can be set so that it'll be easier to determine whether the wireless terminal has gone into buildings and have the capability of checking if it has gone into a specific building. Likewise, while the terminal is turned on, in order calibrate the location, it needs to continuously work the GPS engine which leads to a rapid decrease in terminal's idle time. This thesis proposes some solutions regarding these issues - reducing 20 ~ 30% of the battery consumption for GPS visible situation that can occur when the wireless terminal periodically calibrates its location to determine the in-building status, and extending the idle time of the terminal by flexibly using the suggested GPS calibration time method according to wireless terminal's mobility.

• Journal of Korea Society of Industrial Information Systems
• /
• v.28 no.1
• /
• pp.17-25
• /
• 2023

As the range of use of urban unmanned aerial vehicles (UAV) expands, it is necessary to operate UAVs efficiently because of its limited battery capacity. For this, it is required to find the optimal flight profile with various simulations. Therefore, it is important to predict the power and energy consumption of the UAV battery. In this paper, we analyzed the relationship between the speed and acceleration of the UAV and power consumption during the flight. Then, we derived a linear model, which is easily utilized. In addition, we also derived an accurate power consumption model based on deep neural network learning. To find the efficient model, we used learning data as 1) the GPS 3-axis velocity and acceleration data, 2) the IMU 3-axis velocity only, and 3) the IMU 3-axis velocity and acceleration data. The final model shows 5.86% error rate for power consumption and 1.50% error rate for the cumulative energy consumption.