• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1114-1118
• /
• 2000

Impulsive sound and vibration signals in gear are often associated with their faults. Thus these impulsive sound and vibration signals can be used as indicators in the diagnosis of gear fault. The early detection of impulsive signal due to gear fault prevents from complete failure in gear. However it is often difficult to make objective measurement of impulsive signals because of background noise signals. In order to ease the detection of impulsive signals embedded in background noise, we enhance the impulsive signals using adaptive signal processing.

• Transactions of Materials Processing
• /
• v.6 no.6
• /
• pp.500-507
• /
• 1997

The conventional closed-die forgings had been applied to the forging of spur gears. But the forgings require high forging-pressure. In this paper, new precision forging technology have been developed. The developed technology is two steps forging process. Good shaped products are forged successfully with lower forging-pressure than those of conventional forging. The accuracy of the forged spur gear obtained by new precision forging technology is set nearly equal to that of cut spur gear of fourth and fifth class in Korean industrial standard.

• Journal of the Korean Society of Safety
• /
• v.11 no.3
• /
• pp.53-58
• /
• 1996

This paper deals with the bending fatigue strength of sintering spur gears. The test specimens are used to sintering spur gear to be consisted of Fe-C-Ni-Mn and SCM415 spur gear. The fatigue test at a constant stress amplitude is performed by using an electrohydraulic servo-controlled pulsating tester. The S-N curves are obtained and the enhancement of fatigue strength due to carburized treatment is clarified, Accordingly, this study presents the fatigue strength of sintering spur gear, SCM415 spur gear and carburized gears of them. The strength enhancement due to the carburized treatment is discussed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.1107-1108
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.521-522
• /
• 2013

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.134-154
• /
• 2000

New engine design changes and ever increasing requirements make the design of gear oils challenging. Proper understanding of fundamental lubrication theory and formulation knowledge is necessary to develop new gear oils. This paper provides an overview on fundamentals of lubrication theory and functions of each additive. Also, key technical issues facing gear oils are discussed.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.36 no.1
• /
• pp.46-55
• /
• 2012

Foot and Mouth Disease (FMD) is highly contagious and highly lethal to cloven-hoofed animals. In the winter of 2010, an outbreak of FMD in Korea caused a great deal of economic damage as well as serious mental and physical damage to people who participated in preventive activities. This study provides preliminary data for designing safe and functional protective clothing and gear for individuals who participate in FMD preventive activities. This study was accomplished with multilateral methods such as a documentary survey, field trips, sample analysis of protective clothing and gear, questionnaire studies and focus interviews. As a result, we found that most workers wore low-priced protective clothing that was low in safety functions and rarely wore extra protective gear. Also pointed out was dissatisfaction with: protective clothing and gear, problems related to damage, discomfort, contamination, problems in protective gear related to waterproof functions, protection against harmful substances, discomfort, coldness, and damage. Safe protective clothing could be developed that protects the actual wearers if these results are reflected in the improvement of protective clothing and gear.

• Journal of Institute of Convergence Technology
• /
• v.10 no.1
• /
• pp.25-29
• /
• 2020

Magnetic gears of non-contact power type have great advantages in terms of maintenance and repair than mechanical gears, and are used in various ways. Harmonic gears can derive a higher gear ratio than conventional gears through power transmission through a unique rotation mechanism. Magnetic harmonic gears, in which the gear teeth of the harmonic gears are replaced with magnets, have the advantages of both gears, but are difficult to implement and practical, so many studies are being conducted. In this study, we check whether the results of various types of magnetic gears can be applied to harmonic gears. By applying the axial type magnetic gear to the harmonic gear, the characteristic analysis is conducted to see if the result comparable to the existing radial type magnetic harmonic gear is obtained.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.1
• /
• pp.134-139
• /
• 2010

In this study, we developed the gear type vane damper replacing the link type through gear design using Finite Element Analysis(FEA). FEA about the pinion and the vane shaft in the boss of gear type damper for quality improvement was accomplished. We analyzed fluid flow according to angular displacement. Catched the problem of the torque and backlash bring to the pinion as structure improvement of the forced draft fan(FD FAN). Finally, we compared the gear driving result with simulation. It is the objective of the present study to identify a nonlinear flow rate control of gear type vane damper and to suggest a damper shape with a linear flow rate control. This study is related to the development of gear type vane damper change link type in forced draft fan.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.8
• /
• pp.1506-1511
• /
• 2002

A computer aided expert system fur spur, helical, bevel and worm gears was newly developed by using AutoiCAD system and its AutoLISP computer language in the present study. Two methods are available for a designer to draw a gear. The first method needs the gear design parameters such as pressure, module, number of tooth, shaft angle, velocity, materials, etc. When the gear design parameters are inputted, a gear is drawn in AutoCAD system and maximum allowable power and shaft diameter are calculated additionally. The second method calculates all dimensions and gear design parameters to draw a gear when the information such as transmission, reduction ratio, nm, materials and pressure are inputted. The system includes four programs. Each program is composed of a data input module, a database module, a strength calculation module, a drawing module, a text module and a drawing edit module. In conclusion, the CAD system would be widely used in companies to find the geometric data and manufacturing course.