• 한국소음진동공학회논문집
• /
• 제24권7호
• /
• pp.549-554
• /
• 2014

In general, there has been a lot of research concerned about the gear noise known to be proportional to gear transmission error for external gears likewise spur, helical gear, and hypoid gears. But, In the case of planetary gear set, gear noise study is insufficient because of the difficulty of designing, manufacturing, and understanding of its mechanical system. This study is aimed to develop the transmission error measurement equipment for the planetary gear sets used in the automatic transmission. By comparing the results of the transmission error and noise objectively, user could select the optimized planetary gear set which has quiet noise level before manufacturing the automatic transmission.

• 수산해양기술연구
• /
• 제46권4호
• /
• pp.313-323
• /
• 2010

Fuel consumption in fisheries is a primary concern due to environmental effects and costs to fishermen. Much research has been carried out to reduce the fuel consumption related to fishing operations. The fuel consumption of fishing gear during fishing operation is generally related to hydrodynamic resistance on the gear. This research demonstrates a new approach using numerical methods to reduce fuel consumption. By designing the fishing gear using drawing software, the whole and partial resistance force on the gear can be calculated as a result of simulations. The simulation results will suggest suitable materials or gear structure for reducing the hydrodynamic forces on the gear while maintaining the performance of the gear. This research will helpful to reduce the $CO_2$ emissions from fishing operations and lead to reduce fishing costs due to fuel savings.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.60-63
• /
• 2009

Manufacturing technologies of micro spur gear and micro mold by micro PIM were studied with stainless steel feedstock. For molding of gears, micro mold with gear cavity of 1.2 mm in diameter was produced by wire EDM. The proper injection pressure was selected to 70bar by observation and measuring of shapes and shrinkage of gears before/after sintering. For fabrication of micro mold, a tiny polymer gear was produced by injection into the mold. Then, 316L feedstock was again injected/compressed on the polymer gear and debinded together with polymer gear followed by sintering. As a result, another metal mold with gear cavity reduced to about 20% was fabricated and through repetition of this process chain, micro gear mold with cavity about below 800 um was finally obtained. In reduction of size by injection/compression molding, height of gear tooth was shrunk more and the effort for decrease of roughness of micro cavity were carried out ultrasonic polishing and as a result, the roughness in cavity decreased from 3-4 um to about 200 nm.

• 수산해양교육연구
• /
• 제28권4호
• /
• pp.1014-1023
• /
• 2016

The purpose of this study is to suggest improvement directions and strategies for the minimization of ex-post damage and prevention of the generation of derelict fishing gear which lead to decreased fisheries resources and deteriorated marine ecosystem through ghost fishing and damaging spawning and growth grounds. Current problems related to derelict fishing gear in Korea are lack of reliable data on the generation amount of derelict fishing gear, absence of life-cycle monitoring and management system, insufficient supports for derelict fishing gear collection programs and R&D investment in environmentally friendly fishing gear, etc. Thus, this study suggests three basic improvement directions to prevent the generation and minimize the damage of derelict fishing gear. Such improvement directions contain more detailed strategies such as establishment of fishing gear management law and life-cycle management system, strengthening entry regulations on fisheries causing serious ghost fishing problems, increased supports for R&D investment and dissemination of bio-degradable fishing nets, and promotion of voluntary agreements among competing fishermen's groups.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.94-99
• /
• 2000

When operating NC lathe, gear box which is equipped with gear train and spindle sometimes generates loud noise and excessive vibrations. In order to identify their causes, In this study, torsional and lateral vibration characteristics including critical speeds of the gear train-spindle system are first analyzed by using torsional and lateral vibration models of the gear train and shafts. Natural frequencies and modes of the gear box structure are also analyzed by impulse hammer test. Furthermore, measured vibration and noise signals are analyzed and compared with theoretical analysis results. At last it is concluded that the cause of the excessive mise and vibration is the resonance between gear meshing frequency including its side bands, shaft bending and torsional vibration frequencies, and the natural frequencies of th gear box structure. Consequently the noise and vibration levels are greatly reduced by avoiding resonance between them through the redesign of the gear module.

• 동력기계공학회지
• /
• 제22권6호
• /
• pp.58-66
• /
• 2018

The use of external gear pumps is an effective way to achieve adequate performance at low cost when composing hydraulic systems. The biggest drawback, on the other hand, is the accompanying noise. Gears of continuous contact shape are actively used for the pump recently. The continuous contact shape must be the helical type due to the nature of the gear pump that is driven only by the drive gear. In this paper the theoretical shape of continuous contact gear is analyzed using simple rack shape of straight lines and two circular arcs. Using such geometry, the theoretical equation will be developed by envelope curves according to the conjugate gear shape rules. After checking the validity of the theory by the shape of gear rules, the grinding shape was also developed. The 3D shapes using equation can be also drawn. It was also shown that contact ratio and radius of curvature are easily developed by the theoretical equations.

• 열처리공학회지
• /
• 제32권6호
• /
• pp.270-274
• /
• 2019

In this study, simulation structure analysis was performed for the differential gear system for passenger cars as a prerequisite for the design of the balancing module. The differential gear system was modeled by using CATIA and simulation structure analysis was performed using ANSYS software. The material of the modeled differential gear system uses the mechanical properties of S45C (Q&T). In the structural analysis of the differential gear, the areas where the maximum stress and the maximum strain occurred can be identified. The maximum stress and maximum strain occurred in the pitch circle of the bevel gear. In evaluating the safety factor, it was found that sufficient safety factor was secured. Based on the analysis results for the differential gear, it is expected that it will be a good reference if we design the balancing module device.

• 한국기계가공학회지
• /
• 제18권9호
• /
• pp.81-87
• /
• 2019

The automatic tool changer of a machining center consists of a tool magazine and a cam box, and the core components of the cam box are a roller gear cam and a turret. Recently, the roller gear cam of a cam box has been replaced by a ball gear cam. In this study, the design and machining method of ball gear cam for an automatic tool changer was studied. Additionally, an algorithm for a 4-axis post processing method was established from an instrumental formula by designing a ball gear cam, thus preventing machining at the bottom of ball end mill and enabling the ball on the turret to be driven at the entrance and exit of a curve without collision due to machining errors. In conclusion, machining using only the 4-axis method including the C-axis on a BC -Type 5-axis machine produced the desired ball gear cam.

• 한국기계가공학회지
• /
• 제19권10호
• /
• pp.36-43
• /
• 2020

A marine turning gear is the main auxiliary machine that enables the disassembly of and maintenance on the main engines. In this study, a marine turning gear based on a helical planetary reducer was developed through analysis of a marine turning gear based on a spur planetary reducer. Nonlinear numerical analysis was performed to determine the ideal contact ratio between the sun gear and the idle gear. Based on this, the surface durability, tooth bending strength, and contact ratio were calculated. In addition, the helix direction was selected to utilize the existing bearings. Gears were manufactured based on the helical gear design values, and the turning gear was evaluated using the FTA standards of MAN Co. Ltd. As a result, a lifetime of 3,000 to 5,000 hours was verified, the maximum torque measured was 105kNm, and the efficiency was measured to be 87.4%.

• 한국정밀공학회지
• /
• 제13권4호
• /
• pp.129-135
• /
• 1996

The area of gear vibration and noise, has recently been the focus of many studies. The proper kinematic and geometric design of gears, the mathematical modeling of gear system are essential for a good design. This work present a gear disign for reducing noise, and practical approaches used for machinery noise reduction slong with the summary of methods available for predicting gear noise in terms of the transmis- sion error, and show a comparative study with other methods. A new tooth profile modification is proposed for reducing vibration and noise of involute gears. The method is based on the use of cubic spline curves. The tooth profile is constrained to assume an involute shape during the loaded operation. Thus the new gear profile assures conjugate motion at all points along the line of action. The new profile is found to result in a more uniform static transmission error compared to not only standard involute profile but also modificated profile therby contributing to the improvement of vibration and noise characteristics of the gear.