• Tribology and Lubricants
• /
• v.38 no.1
• /
• pp.22-26
• /
• 2022

A 1.7-ton grade small excavator is a construction equipment that can perform various functions in limited spaces where heavy equipment cannot enter easily. Owing to the recent acceleration of urbanization, it has been used increasingly in drainage and gas pipes, as well as for road repair works in urban areas. The power train of a traveling reducer for a 1.7-ton grade small excavator utilizes a complex planetary gear system. Complex planetary gears are vital to the power train of a traveling reducer as it mitigates the fatigue strength problem. In the present study, the specifications of a complex planetary gear train are calculated; furthermore, the gear bending and compressive stresses of the complex planetary gears are analyzed to achieve an optimal design of the latter in terms of cost and reliability. In this study, the actual gear bending and compressive stresses of a planetary gear system are analyzed using a self-developed gear design program based on the Lewes and Hertz equation. Subsequently, the calculated specifications of the complex planetary gears are verified by evaluating the results with the data of allowable bending and compressive stress based on curves of stress vs. number of cycles of the gears.

• Journal of the Korean Society of Industry Convergence
• /
• v.9 no.4
• /
• pp.269-276
• /
• 2006

Strength Design method for involute spur gears is developed. The developed gear strength design system can design the optimized gear that minimize the number of pinion teeth with face tooth. Method of optimization is matrix form which is developed from this study. Design variables are transmitted power, gear volume, gear ratio, allowable contact stress and allowable bending stress, etc. Gear design method developed this study can be apply to the gears of plants, machine tools, automobiles.

• 한국기계연구소 소보
• /
• s.15
• /
• pp.25-35
• /
• 1985

During one revolution of a gear, the intensity of the gear-meshing noise or vibration will vary, depending upon the run-out in the pitch diameter of the gear. Here noise can be produced bu excentricity of the shaft with respect to the base circle and by pitch errors. According to the noise generated is clearly dependent on the force and the amount of energy expended in elastically straining the machine member. The purpose of this paper is to discuss the analysis of the noise and technical reduction of gear noise for machine tool.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.698-701
• /
• 1997

In this paper, we developed an automated program for the design and machining of spiroid bevel gear. A computer program employing the theory of gearing between gear and pinion is developed to design gear mechanism. A new method for machining spiro야 bevel gears is proposed, and effectively used for an example.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.5
• /
• pp.28-33
• /
• 1998

In monitoring and diagnosing machinery with gear trains, gear meshing force are the important signature indicating the operating condition. The gear meshing forces, however, are extremely difficult to be measured while gears are rotating. One easy possible way is to measure vibrations which are produced and transferred by the gear meshing forces. While the gear meshing forces are traveling, the force waveforms are shaped by the path transfer function. In the paper, the way to recover the source waveform by eliminating the path effects is discussed using inverse filter.

• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.39-46
• /
• 1997

This study describes a computer aided design system on involute gear for power transmition. Input data for gear design are pressure angle $20^{\circ}$, transmitted power, gear volume, gear ratio, addendum ratio of rack, dedendum ratio of rack, edge radius of rack, allowable contact stress and allowable bending stress etc. Bending strength contact strength and scoring are considered as the design constraints. Method of optimization developed this study. The developed gear design system can design the optimized gear that minimize the number of pinion teeth with face tooth.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.34-46
• /
• 1987

The drive efficiency is investigated with drawbar pull test to provide the basic data in the gradability and acceleration of the wheeled vehicle. As a result, the drive efficiencies are determined from 4*2 drive : Direct gear 0.89 1st gear 0.81 Other gears 0.83-0.87 4*4 high drive : Direct gear 0.85 1st gear 0.77 Other gears 0.79-0.83 4*4 low drive : Direct gear 0.83 1st gear 0.75 Other gears 0.77-0.81

• Journal of the Korean Society of Safety
• /
• v.18 no.4
• /
• pp.44-50
• /
• 2003

Design method for involute bevel gears is developed. The developed gear design system can design the optimized gear that minimize the number of pinion teeth with face tooth. Method of optimization is MS(matrix search) which is developed from this study. Design variables are pressure angle 20., transmitted power, gear volume, gear ratio, allowable contact stress and allowable bending stress. etc. Gears design method developed this study can be applied to the plane, helicopter, printer, machine tools.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.1
• /
• pp.198-205
• /
• 1998

In this paper, the dynamic characteristics of a star type epicyclic gear train have been analyzed. Nonlinear stiffness of a gear pair were obtained considering the bending and shear deformation, Hertz contact deformation, as well as tooth fillet deformation. Nonlinear stiffness coefficients and damping coefficients around the static equilibrium position were obtained by perturbation method. The loci of the planet gears and sun gear were estimated. Tooth meshing forces and bearing reaction forces were calculated. The effects of bearing clearance and oil viscosity on the gear behavior were also analyzed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.5
• /
• pp.96-101
• /
• 1999

This study suggests an algorithm for tooth profile generation of free from curve involute gear, a special gear of which the pitch line is a free curve instead of a circular one. For the first, a methodology for calculation of the tooth curve is developed and formulated Then the formulated algorithm, is programmed for manufacturing and verified by computer graphics. Next the calculated results as changed in to NC codes to apply to wire electric discharge machine(WEDM). Finally, the machined gear is examined in engagement with a standard involute gear.