• Journal of ILASS-Korea
• /
• v.22 no.1
• /
• pp.8-12
• /
• 2017

Recently, manufacture and sales of passenger car with GDI (Gasoline Direct injection) were dramatically increased in Korea. In this study, investigation on the exhaust emission characteristics of GDI vehicles according to mileage were conducted by using chassis dynamometer and emission analyzer. Test cars selected 5 types with G4FD engine (1600 cc) and emissions of total 14 vehicles analyzed. Measurement and evaluation on emissions (CO, NOx, NMOG, $CO_2$) characteristics of GDI vehicles with mileages from 40,000 to 80,000 km in certification driving cycle (CVS-75) were carried out in this study. It is revealed that emission results of all test cars shows below emission standard, NMOG emission value of about 80,000 km doubled that of 40,000 km and emission increased by accumulated mileage. Also, increasing pattern of NOx emissions shows when the vehicle mileages was increased and $CO_2$ emission increasing trend obviously do not show according to mileages.

• Journal of ILASS-Korea
• /
• v.25 no.4
• /
• pp.162-169
• /
• 2020

The worldwide focus on reducing the emissions, fuel and lubricant consumption in T-GDI engines is leading engineers to consider the crankcase ventilation and oil mist separation system as an important means of control. In today's passenger cars, the oil mist separation systems mainly use the inertia effect (e.g. labyrinth, cyclone etc.). Therefore, this study has investigated high efficiency cylinder head-integrated oil-mist separator by using a compact multi-impactor type oil mist separator system to ensure adequate oil mist separation performance. For this purpose, engine dynamometer testing with oil particle efficiency measurement equipment and 3D two-phase flow simulation have been performed for various engine operating conditions. Tests with an actual engine on a dynamometer showed oil aerosol particle size distributions varied depending on operating conditions. For instance, high rpm and load increases bot only blow-by gases but the amount of small size oil droplets. Submicron-sized particles (less than 0.5 ㎛) were also observed. It is also found that the impactor type separator is able to separate nearly no droplets of diameter lower than 3 ㎛. CFD results showed that the complex aerodynamics processes that lead to strong impingement and break-up can strip out large droplets and generate more small size droplets.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.5
• /
• pp.455-461
• /
• 2015

A high-pressure fuel pump is a key component in a gasoline direct injection (GDI) engine; thus, understanding its flow characteristics is essential for improving the engine power and fuel efficiency. In this study, AMESim, which is a hydraulic analysis program, was used to analyze the performance of the high-pressure fuel pump. However, since AMESim uses a one-dimensional model for the system analysis, it does not accurately analyze the complicated flow characteristics. Thus, Fluent, computational fluid dynamics (CFD) software, was used to calculate the flow rates and net forces at the intake and discharge ports of the high-pressure fuel pump where turbulent flow occurs. The CFD analysis results for various pressure conditions and valve lifts were used as look-up tables for the AMEsim model. The CFD analysis results complemented the AMEsim results, and thus, improved the accuracy of the performance analysis results for the high-pressure fuel pump.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.981-987
• /
• 2011

In this study, single cylinder engine experiment was carried out to investigate combustion characteristics spray guided direct injection spark ignition engine. In the result of engine experiment, it was shown that flammable window of injection timing was existed. The combustion efficiency increased with retarding injection timing, reaching a peak value, subsequent to decrease again. These results were likely due to the effect of ambient pressure on stratified-premixed mixture preparation. 150 bar injection pressure condition and retarded injection timing from the best combustion efficiency injection timing showed the highest IMEP value due to the advanced combustion phase of the maximum combustion efficiency condition. HC emission showed same trend of combustion efficiency, and smoke emission was increased as injection timing was retarded due to the increased locally rich area in the high ambient pressure. NOx emission showed decreasing trend as injection timing was retarded. This is likely due to the maximum in-cylinder temperature was decreased with retarded combustion phase.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.704-709
• /
• 2000

Laminar burning velocities of propane- and iso-octane-air mixtures have been numerically modelled over a wide range of equivalence ratio, pressure and temperature. These correlations are applicable to the modelling of stratified charged combustion like that of lean bum and GDI engine combustion. The numerical models are based on the results calculated by PREMIX code with Sloane's detailed chemical reaction mechanism for propane and FlameMaster code with Peters' for iso-octane. Laminar burning velocity for two fuels showed a pressure and temperature dependence in the following form, in the range of $0.1{\sim}4MPa$, and $300{\sim}1000K$, respectively. $S_L={\alpha}\;{\exp}[-\xi({\phi}-{\phi}_m)^2-{\exp}\{-{\xi}({\phi}-{\phi}_m)\}-{\xi}({\phi}-{\phi}_m)]$ where ${\phi}_m=1.07$, and both of ${\alpha}$ and ${\xi}$ are functions of pressure and temperature. Compared with the results of the existing models, those of the present one showed the good agreement of the recent experiment data, especially in the range of lean and rich sides. Judging from the calculated results of the stratified charged combustion by using STAR-CD, the above modelling prove to be more suitable than the other ones.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.10
• /
• pp.1303-1310
• /
• 2001

In order to be applicable to the combustion modelling of stratified charged combustion like that of - lean burn and GDI engine, the correlations of laminar burring velocities fur several hydrocarbon fuels and methanol are needed over a wide range of equivalence ratio, pressure and temperature. In this study, these correlations are modeled in the 1311owing form based on the experimental and Muller\`s modeling results for several fuels, where $\alpha$, ξ, and ξ are functions of pressure and temperature, $S_{L}$ =$\alpha$ exp[-ξ($\Phi$-$\Phi$$_{m}$)$^{2}$ -exp {-ζ($\Phi$-$\Phi$$_{m}$)}-ζ($\Phi$-$\Phi$$_{m}$)]. By using the results calculated by PREMIX code with Sloane\`s detailed chemical reaction mechanism for propane, it is verified that the coefficients of the abode modeling can be determined by considering laminar burning velocity data only in a range of equivalence ratio less than $\Phi$$_{m}$. Therefore, Muller\`s modeling results can be adopted leer modeling of the pressure and temperature dependency. Compared with the results of the existing Keck'and Gulder's models, those of the present one showed the good agreement of the recent experimental data, especially in the range of lean and rich sides.s.des.s.