• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.100-102
• /
• 2003

This system is capable of obtaining quantitative information from images using natural features on the ortho-image maps that correspond with those from topographical maps. However, the qualitative information can also be obtained because because of the excellent visibility of ortho-image maps. There are plenty of promise for the use of ortho-image maps in the next generation topographic technology because of its wider applicability within the field. In keeping with the cutting edge, we produced ortho-image maps by scanning a specified area in narrow sections using the PKNU 2: a multispectral digital aerial photographing system made by ourselves. We evaluated the precision of the ortho-image maps, and performed an evaluation of the PKNU 2 system's capacity to improve the equipment of the PKNU 2. Ortho-image maps were made using Ground Control Points (GCPs) which were obtained from digital maps and aerial photographs of the PKNU 2. Thus, we demonstrated that it was possible to produce the ortho-image maps, which has a good constant level rate of less than 1m. The PKNU 2 system needs to be improving in the sensitivity of level maintenance equipment in the evaluation in terms of performance. It is thus required to survey the GCPs precisely for an accurate study.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.34 no.2
• /
• pp.133-142
• /
• 2016

KOMPSAT-3A (KOrea Multi-Purpose SATellite-3A) was launched in March 25 2015 with specification of 0.5 meters resolution panchromatic and four 2.2 meters resolution multi spectral sensors in 12km swath width at nadir. To better understand KOMPSAT-3A positional accuracy, this paper reports a test result on the accuracy of recently released KOMPSAT-3A beta test images. A number of ground points were acquired from 1:1,000 digital topographic maps over the target area for the accuracy validation. First, the original RPCs (Rational Polynomial Coefficients) were validated without any GCPs (Ground Control Points). Then we continued the test by modeling the errors in the image space using shift-only, shift and drift, and the affine model. Ground restitution accuracy was also analyzed even though the across track image pairs do not have optimal convergence angle. The experimental results showed that the shift and drift-based RPCs correction was optimal showing comparable accuracy of less than 1.5 pixels with less GCPs compared to the affine model.

• Korean Journal of Remote Sensing
• /
• v.14 no.2
• /
• pp.137-148
• /
• 1998

An algorithm developed for the precision correction of high resolution satellite images is introduced in this paper. In general, the polynomial warping algorithm which derives polynomial equations between GCPs extracted from an image and a base map requires many GCPs well-distributed over the image. The precision correction algorithm described in this paper is based on a sensor-orbit-Earth geometry, and therefore, it is capable of correcting a raw image using only 2-3 GCPs. This algorithm estimates the errors on the orbit determination and the attitude of the satellite by using a Kalman filter. This algorithm was implemented, tested and integrated into the KITSAT-3 image preprocessing software.

• Journal of Korean Society for Geospatial Information Science
• /
• v.22 no.4
• /
• pp.127-133
• /
• 2014

The purpose of this study is to evaluate the accuracy of Network-RTK(VRS) survey for applying to Ground Control Points(GCPs) survey required for mapping aerial photographs. Network-RTK has been serviced by National Geographic Information Institute since 2007. On the basis of the global coordinates system(ITRF2000), the coordinates of GCPs determined by Static GNSS survey with relative positioning techniques were regarded as accurate values. The coordinates of GCPs were also determined by Network-RTK survey using two kinds of receivers, and then they were converted into the global coordinates system(ITRF2000) by applying suitable geoid model and coordinate transformation. These coordinates of GCPs were compared with those from Static GNSS survey. The root mean squares error (RMSE) of coordinate differences between Network-RTK and Static GNSS was ${\pm}2.0cm$ in plane and ${\pm}7.0cm$ in height. Therefore, Network-RTK survey that enables single GNSS receiver to measure positions in short time is a practical alternative in positioning GCPs to either RTK survey that uses more than two sets of GNSS receivers or Static GNSS survey that requires longer observation time.

• Journal of Korean Society for Geospatial Information Science
• /
• v.10 no.4 s.22
• /
• pp.41-50
• /
• 2002

RPM is the one of the sensor models which is proposed by Open GIS Consortium (OGC) as image transfer standard. And it is the sensor model for end-users using IKONOS, a commercial pushbroom satellite, imagery which provide about 1m ground resolution. Parameters called RPC which is IKONOS RFM coefficients are serviced to end-users. But if some users try to make additional effort to get rigorous geo-spatial information, it is necessary to apply mathematic or abstract sensor models, because vendors don't offer any ancillary data for physical sensor models such as satellite orbit and navigation. Abstract sensor models such as pushbroom Direct Linear Transform (DLT) require many GCPs well distributed in imagery, and mathematic sensor model such as RFM, polynomials need much more GCPs. Therefore RPC modification using additional a few GCPs is the best solution. In this paper, two methods are proposed to modify RPC. One is method to use pseudo GCPs generated in normalized cubic, and another method uses parameters observations and a few GCPs. Through two methods, we get improvement of accuracy 50% and over.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.36 no.4
• /
• pp.279-286
• /
• 2018

In the civil works, the measurement of earth-volume is one of the important elements in the estimation of the reasonable construction cost. Related studies mainly used GPS (Global Positioning System) or total station to obtain information on civil work areas. However, these methods are difficult to implement in inaccessible areas. Therefore, the aim of this paper is to use the UAV (Unmanned Aerial Vehicle) to measure the earth-volume. The study area is located in a reservoir construction site in Sangju-si, Gyeongsangbuk-do, Republic of Korea. We compared the earth-volume amounts acquired by UAV-based surveying to ones acquired by total station-based and GPS-based surveying, respectively. In the site, the amount of earth-volume acquired by GPS was $147,286.79m^3$. The amount of earth-volume acquired by total station was $147,286.79m^3$, which is the 96.13% accuracy compared to the GPS-based surveying. The earth-volume obtained by UAV was $143,997.05m^3$ when measured without GCPs (Ground Control Points), $147,251.71m^3$ with 4 GCPs measurement, and $146,963.81m^3$ with 7 GCPs measurement. Compared to the GPS-based surveying, 97.77%, 99.98%, and 99.78% accuracies were obtained from the UAV-based surveying without GCP, 4 GCPs, and 7 GCPs, respectively. Therefore, it can be confirmed that the UAV-based surveying can be used for the earth-volume measurement.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2007.04a
• /
• pp.455-458
• /
• 2007

Currently, aortal surveying is getting advanced in the world. New digital equipment for aerial surveying makes improvement of accuracy, economical efficiency and reduces cost. for a result, however, there are required to produce a accurate product. In this study, we used two kinds of data, the one which used only GPS/INS data and the other one which used GPS/INS data added on GCPs from digital maps, and made as a mosaic to compare both of them whether which one is better based on digital maps. the result is that the data which used GPS/INS data added on GCPs from digital maps was a lot better than GPS/INS data.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.30B no.1
• /
• pp.29-37
• /
• 1993

The purpose of this paper is to estimate the attitude and the position of SPOT satellite which are needed in producing DEM(Digital Elevation Model) using SPOT satellite image pairs. DEM extraction is consists of three parts. First part is the modeling of satellite position and atitude, second part is the matching of two images to find corresponding point of them and third part is to calculate the elevation of each point by using the result of the first and second part. For modeling inaccessible area, extended modeling algorithm which removes the GCP(Ground Control Point) most errorneous from the GCPs extracted from map iteratively is proposed According to the experiments using a collinearity equation, the second order polynomials are shown to the optimal for .omega.(pitch), and Zs parameters while the first order ones for .kappa.(yaw) .PHI.(roll), Xs, and Ys parameters. The input images used in this paper are 6000*6000 level 1A panchromatic digital SPOT images of Chungchong-do, Korea. With 30 GCPs, experiments on SPOT images show that the planimetric and altimetric RMS errors are 7.11m and 7.10m, respectively, for test points.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.5
• /
• pp.485-491
• /
• 2008

LiDAR systems are usually incorporated a laser scanner and GPS/INS modules with a digital aerial camera. LiDAR point clouds and digital aerial images acquired by the systems provide complementary spatial information on the ground. In addition, some of laser scanners provide intensity, radiometric information on the surface of the earth. Since the intensity is unnecessary of registration and provides the radiometric information at a certain wavelength on the location of LiDAR point, it can be a valuable ancillary information but it does not deliver sufficient radiometric information compared with digital images. This study utilize the LiDAR points as ground control points (GCPs) to adjust exterior orientations(EOs) of the stereo images. It is difficult to find exact point of LiDAR corresponding to conjugate points in stereo images, but this study used intensity of LiDAR as an ancillary data to find the GCPs. The LiDAR points were successfully used to adjust EOs of stereo aerial images, therefore, successfully provided the prerequisite for the precise registration of the two data sets from the LiDAR systems.

• Proceedings of the KSRS Conference
• /
• 2008.10a
• /
• pp.37-40
• /
• 2008

The purpose of this paper is to extract DEMs from Spot-3 strips using orbit modeling technique. Spot-3 stereo strip images along 420km in distance were used for experiments. The orbit modeling technique has been suggested to establish accurate geometric models for a whole strip taken on the same orbit using only a small number of GCPs on the top area of the strip. This method enables extraction of orientation parameters of the scene along the strip that is needed to generate DEMs. Consequently, we were able to extract DEMs over the areas without accurate GCPs obtained by GPS surveying per each scene. Assessment of accuracy was carried out using USGS DTED. DEMs generated from the orbit modelling technique suggested showed satisfactory performance when quantitative analysis of accuracy assessment was carried out.