• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.2 s.105
• /
• pp.134-138
• /
• 2006

The isolation performance of the S-band single-pole single-throw(SPST) monolithic microwave integrated circuit (MMIC) switch with two different RF-interconnection approaches, microstrip and grounded coplanar waveguide(GCPW) lines, are investigated. On-to-off isolation is improved by 5.8 dB with the GCPW design compared with the microstrip design and additional improvement of 6.9 dB is obtained with the coplanar wire-bond interconnection(CWBI) at a 3.4 GHz. The measured insertion loss and third-order inter-modulation distortion(IMD3) are less than 1.94 dB over $3.2{\sim}3.6\;GHz$ and greater than 64 dBc.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.111-114
• /
• 2005

The isolation performance of the S-band single-pole single-throw (SPST) monolithic microwave integrated circuit (MMIC) switch with two different RF-interconnection approaches, microstrip and grounded coplanar waveguide (GCPW) lines, are investigated. On-to-off isolation is improved by 5.8 dB with the GCPW design compared with the microstrip design and additional improvement of 6.9dB is obtained with the coplanar wire-bond interconnection (CWBI) at 3.4 GHz. The measured insertion loss and third-order inter-modulation distortion (IMD3) are less than 2.43 dB over 2.5 CHz $\sim$ 4 GHz and greater than 64 dBc.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.6
• /
• pp.25-29
• /
• 2017

This paper presents a hetero-integration of electrostatically actuated RF MEMS Switch and step up DC-DC converter on a redistribution layer using commercial PCB process. RF characteristics of Duroid with $56{\Omega}$ impedance GCPW transmission line and that of FR4 with $59{\Omega}$ impedance CPW transmission line were analyzed. From DC to 6GHz, RF characteristics of Duroid were better than that of FR4, insertion loss was 2.08dB lower, return loss was 3.91dB higher, and isolation was 3.33dB higher.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.5
• /
• pp.444-449
• /
• 2003

In this paper, a PCB(Printed Circuit Board) antenna for IMT-2000 is designed and analyzed. The antenna has a helical structure with via-holes and lines on FR-4($\varepsilon$$\sub$${\gamma}$/=4.6 ) PCB, and the type of feeding is GCPW(Grounded Co-Planar Waveguide). Using HFSS of Ansoft, the antenna was designed and the measured results of frequency and radiation characteristic,3 with VSWR<2.0 are satisfied within operating frequency band of 1.920∼2.170 GHz. And it has resonating frequency of 2.045 GHz and a bandwidth of 321 MHz. The radiation gain of the antenna was measured to be -1 dBi.

• Journal of Advanced Navigation Technology
• /
• v.9 no.2
• /
• pp.147-155
• /
• 2005

In this paper, we propose that three uniform coplanar waveguides(CPWs), such as a conventional, finite grounded(FG), and grounded(G) CPWs, can be coupled with a $TE_{01{\delta}}$ mode dielectric resonator(DR) for a parallel resonant characteristic as a microstrip line coupled with the DR. Coupling characteristics have been investigated by placing the DR on a dielectric support above the CPWs and by moving the DR away from the center of a slot of the CPWs to the ground plane. FEM simulation(HFSS) results in terms of S-parameters agree well with measurement results. Finally, unloaded Q values of the DR coupled with the three uniform CPWs are compared with those of the DR coupled with a microstrip line. The comparison shows that the DR coupled with the three CPWs has higher unloaded Qs than that coupled with a microstrip line and that the GCPW case has the highest unloaded Qs.