• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.10
• /
• pp.1384-1392
• /
• 2014

This paper presents a torque ripple reduction algorithm for the switched reluctance motor drives using the fuzzy logic and the sliding mode control. A turn-on angle controller based on the fuzzy logic determines the optimal turn-on angle. In addition, a sliding mode torque control (SMTC) methods reduces torque ripples instantaneously in the commutation region. The proposed algorithm does not require complex system models considering nonlinear magnetizing or demagnetizing periods of the phase current. According to the rotor speed and torque, the proposed controller changes the turn-on angle and reference torque instantaneously until the torque ripples are minimized. The simulation and experimental results verify the validity of minimizing the torque ripple performance.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.78-90
• /
• 2017

This paper presents the design of closed loop controllers operating a single-phase AC-DC three-level converter for improving power quality at AC mains. Closed loop inhibits outer voltage controller and inner current controller. Simulations of three level converter with three different voltage and current controller combinations such as PI-Hysteresis, Fuzzy-Hysteresis and Fuzzy tuned PI-Hysteresis are carried out in MATLAB/Simulink. Performance parameters such as input power factor and source current total harmonic distortion (THD) are considered for comparison of the three controller combinations. The fuzzy-tuned PI voltage controller with hysteresis current controller combination provides a better result, with a source-current THD of 0.93% and unity power factor without any source side filter for the three level converter. For load variations of 25% to 100%, a THD of less than 5% is obtained with a maximum value of only 1.67%. Finally, the fuzzy-tuned PI voltage with hysteresis controller combination is implemented in a Xilinx Spartan-6 XC6SLX25 FPGA board for experimental validation of power quality enhancement. A prototype 100 W, 0-24-48 V as output converter is considered for the testing of controller performance. A source-current THD of 1.351% is obtained in the experimental study with a power factor near unity. For load variations of 25% to 100%, the THD is found to be less than 5%, with a maximum value of only 2.698% in the experimental setup which matches with the simulation results.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.52 no.1
• /
• pp.36-43
• /
• 2003

This paper presents an optimal tuning method for Fuzzy Logic Controller (FLC) of current controller for HVDC using Genetic Algorithm(GA). GA is probabilistic search method based on genetics and evolution theory. The scaling factors of FLC are tuned by using real-time GA. The proposed tuning method is applied to the scaled-down HVDC simulator at Korea Electrotechnology Research Institute(KERI). Experimental result shows that disturbances are well-damped and the dynamic performances of FLC have the better responses than those of PI controller for small and large disturbances such as ULTC tap change, reference DC current change and DC ground fault.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.1
• /
• pp.95-103
• /
• 2008

This paper deals with the problem of autolanding for aircraft under windshear environment for which the landing trajectory is given. It is well known that the landing maneuver in windshear turbulence is very dangerous and hard for the pilot to control because windshear is unpredictable in when and where it happens and its aerodynamic characteristics are complicated. In order to accomplish satisfactory autolanding maneuver in this environment, we propose a gain-scheduled controller. The proposed controller consists of three parts: PID controller, called baseline controller, which is designed to satisfy requirements of stability and performance without considering windshear, gain scheduler based on fuzzy logic, and safety decision logic, which decides if the current autolanding maneuver needs to be aborted or not. The controller is applied to a 6-DOF simulation model of the associated airplane in order to illustrate the effectiveness of the proposed control algorithm. It is noted that a cross wind in the lateral direction is included to the simulation model. From the simulation results it is observed that the proposed gain scheduled controller shows superior performance than the case of controller without gain scheduling even in severe downburst and tailwind region of windshear. In addition, touchdown along centerline of the runway is more precise for the proposed controller than for the controller without gain scheduling in the cross wind and the tailwind.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.10
• /
• pp.100-106
• /
• 2006

This paper proposes a full fuzzy-logic-based vector control for a permanent-magnet synchronous motor (PMSM). The high-performance of the proposed fuzzy logic control (FLC)-based PMSM drive are investigated and compared with the conventional proportional-integral (PI) controller at different conditions, such as step change in command speed and load and etc. In the experimental and simulation the FLC is employed in the speed and current controller. The experimental results show to be a suitable replacement of the conventional PI controller for the high-performance drive system.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.385-387
• /
• 1995

The current mode controlled DC/DC converter using fuzzy logic controller is proposed. With the proposed control method, the robust and safty guaranteed operation are achieved. For comparison with conventional controller, the PI controller is selected. By the computer simulation results, the validities of the proposed control method will be shown.

• Journal of the Korean Society of Safety
• /
• v.14 no.4
• /
• pp.108-113
• /
• 1999

This paper presents a study on fuzzy speed and flux controller used in a vector control of a CRPWM(Current Ragulated PWM) induction motor drive. In this paper, an approach for an easier design of the fuzzy controller is presented in order to obtain the desired value for the response time with minimal overshoot and to improve the steady state performance for speed step commands. The fuzzy controller is constructed only upon the knowledge of the motor behaviour and the desired speed response, and provides fast and robust control by reducing the effects of nonlinearities, parameter changes and load disturbance. The results of applying the fuzzy logic controller to an IM drive system are compared with those obtained by application of a conventional PI controller. The fuzzy controller provided a better response than the PI controller.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.51 no.6
• /
• pp.252-257
• /
• 2002

We designed a neuro-fuzzy controller to improve some problems that are happened when the DC servo motor is controlled by a PID controller or a fuzzy logic controller. Our model proposed in this paper has the stable and accurate responses, and shortened settling time. To prove the capability of the neuro-fuzzy controller designed in this paper, the proposed controller is applied to the speed control of DC servo motor. The results showed that the proposed controller did not produce the overshoot, which happens when PID controller is used, and also it did not produce the steady state error when FLC is used. And also, it reduced the settling time about 10%. In addition, we could by aware that our model was only about 60% of the value of current peak of PID controller.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.708-713
• /
• 2000

A research on the AFC(Auto Feedrate Control) by a fuzzy controller using a tool dynamometer and motor currents was conducted. For simulations, cutting dynamics of end-milling process was modeled by geometric relationship between tool and work-piece. The fuzzy logic controller was employed to track the desired cutting force and showed good performance in simulations and several experiments. The spindle motor currents was modeled to estimate cutting force and successfully used for the AFC.

• Journal of Power Electronics
• /
• v.15 no.5
• /
• pp.1329-1337
• /
• 2015

By placing distributed generation power sources beside a big nonlinear load, these sources can be used as a power quality enhancer, while injecting some active power to the network. In this paper, a new scheme to use the distributed generation power source in both operation modes is presented. In this scheme, a fuzzy controller is added to adjust the optimal set point of inverter between compensating mode and maximum active power injection mode, which works based on the harmonic content of the nonlinear load. As the high order current harmonics can be easily rejected using passive filters, the DG is used to compensate the low order harmonics of the load current. Multilevel transformerless cascade inverters are preferred in such utilization, as they have more flexibility in current/voltage waveform. The proposed scheme is simulated in MATLAB/SIMULINK to evaluate the circuit performance. Then, a 1kw single phase prototype of the circuit is used for experimental evaluation of the paper. Both simulative and experimental results prove that such a circuit can inject a well-controlled current with desired harmonics and THD, while having a smaller switching frequency and better efficiency, related to previous 3-phase inverter schemes in the literature.