• Geomechanics and Engineering
• /
• 제22권1호
• /
• pp.97-108
• /
• 2020

The time-consuming and less objectivity are the main problems of conventional micromechanical parameters calibration method of Particle Flow Code simulations. Thus this study aims to address these two limitation of the conventional "trial-and-error" method. A new calibration method for the linear parallel bond model (CM-LPBM) is proposed. First, numerical simulations are conducted based on the results of the uniaxial compression tests on limestone. The macroscopic response of the numerical model agrees well with the results of the uniaxial compression tests. To reduce the number of the independent micromechanical parameters, numerical simulations are then carried out. Based on the results of the orthogonal experiments and the multi-factor variance analysis, main micromechanical parameters affecting the macro parameters of rocks are proposed. The macro-micro parameter functions are ultimately established using multiple linear regression, and the iteration correction formulas of the micromechanical parameters are obtained. To further verify the validity of the proposed method, a case study is carried out. The error between the macro mechanical response and the numerical results is less than 5%. Hence the calibration method, i.e., the CM-LPBM, is reliable for obtaining the micromechanical parameters quickly and accurately, providing reference for the calibration of micromechanical parameters.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.362-371
• /
• 2006

The behaviour characteristics of Granular Compaction Pile(GCP) are mainly governed by the lateral confining pressure mobilized in the matrix soft soil to restrain the bulging failure of the granular compaction pile. The GCP method is most effective in soft soil with untrained shear strength ranging from $15\sim50\;kPa$. However, the efficiency of this method is falling down in the more compressible soil conditions, which does not provide sufficient lateral confinement. In the present study, the GCP method reinforced with uniformly graded permissible concrete is suggested for the extension of application to the soft ground. Also, large triaxial compression tests are conducted on composite- reinforced soil samples for verification of availability of the suggested method and the settlement estimation method of the reinforced GCP is proposed. Further, for the verification of a validity of the proposed method, predicted settlements are compared with results of numerical analyses. Tn addition, parametric studies are performed together with detailed analyses of relevant design parameters.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권1호
• /
• pp.44-57
• /
• 2016

Rectification is used as a preprocessing to reduce the computation complexity of disparity estimation. However, rectification also requires a complex computation. To minimize the computing complexity, rectification using a lookup-table (R-LUT) has been introduced. However, since, the R-LUT consumes large amount of memory, rectification with compressed LUT (R-CLUT) has been introduced. However, the more we reduce the memory consumption, the more we need decoding overhead. Therefore, we need to attain an acceptable trade-off between the size of LUT and decoding overhead. In this paper, we present such a trade-off by adaptively combining simple coding methods, such as differential coding, modified run-length coding (MRLE), and Huffman coding. Differential coding is applied to transform coordinate data into a differential form in order to further improve the coding efficiency along with Huffman coding for better stability and MRLE for better performance. Our experimental results verified that our coding scheme yields high performance with maintaining robustness. Our method showed about ranging from 1 % to 16 % lower average inverse of compression ratio than the existing methods. Moreover, we maintained low latency with tolerable hardware overhead for real-time implementation.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1997년도 특별강연 및 추계학술발표 개요집
• /
• pp.184-193
• /
• 1997

Aluminium and aluminium alloys have the high electrical and heat conductivity. It gives rise to difficulties for a choice of electrodes material for their contact electric welding. This paper describes the investigations performed to solve the above problem. The purpose of this investigation was to obtain dispersion-hardening alloys by the internal oxidation method, to optimize their contents and treatment modes, to produce electrodes of these alloys and to test them. The strengthing effect of alloys with oxide particles depends on their size stability at high temperatures. Despite of the fact, that oxides are the most stable of all the non-metallic phases their coagulation takes place. Based on the early results, we chose two types of alloys, first No. 1 Cu - 0,4%Al and second No. 2 Cu - 0,2%Be for production of electrodes. These alloys had not additional alloying elements. These alloys were prepared as 1 mm plates and flake-formed 200 m thick, and also No. 1 as a powder of size 100 mkm (received from Korea). The large samples for electrodes were produced by three methods : explosive welding method, dynamic one including the explosion compression of electrode blank and the quasi-dynamic method including the high-speed compression of dense briquest and the further hot extrusion of a rod.

• 한국재료학회지
• /
• 제28권1호
• /
• pp.1-5
• /
• 2018

Gas detection is necessary for various reasons, including the prevention of gas leakages and the creation of necessary environmental conditions. Among the gas detection methods, leakage of gas can be confirmed using materials that undergo color changes that are easily distinguished by the naked eye. Metal nanoparticles (NPs) experience variations in their absorption wavelengths under the localized surface plasmon effect (LSPR) with mechanical stresses, which change the distance between NPs. In this study, we attempted to detect the presence of gas utilizing the LSPR-related color change of a chain of Au NPs. The assembly of Au NPs, arranged in a chain shape, experienced a color change from dark blue to purple with a change in the distance between the NPs by applying a physical force, i.e., compression, stretching, and gas pressure. As the force of compression and the degree of stretching increased, the absorption wavelength shifted from doublet peaks at 650 and 550 nm to a singlet peak at 550 nm. Further, applying gas pressure caused an identical color change. With this result, we propose a method that could be applied to all gases that require detection based on gas pressure.

• Journal of the Korean Wood Science and Technology
• /
• 제37권5호
• /
• pp.465-473
• /
• 2009

Three failure theories were studied to evaluate the wood strength variation with grain slope. Maximum stress theory, Tsai-Hill theory and Hankinson formula were presented to hypothesize the failure of wood according to grain slope to loading direction. Red pine and Japanese larch were used as materials to simulate failure strength prediction with grain slope. Calculation of strength results was that the strength of wood drops rapidly between parallel to grain orientation (0 degree) and 15 degree grain orientation. The strength of wood with grain orientation were somewhat different at small grain angles among failure theories, and this tendency was due to tension and compression distinction, and shear accounting in each theories. For the above 45 degree grain orientation, the predicted failure strength of wood with grain variation were very close in each failure theories and were useful in assessing failure strength of wood. The applicable these theories should be considered that the wood has different behavior in tension and compression, and this lead to different strength at small grain angles in each theories. Furthermore, reconsideration is needed to assess the failure strength of wood at small grain angles in Hankinson formula and further studies are necessary to accounting for shear behavior at small grain angles.

• 한국자동차공학회논문집
• /
• 제16권5호
• /
• pp.157-163
• /
• 2008

The HCCI combustion mode poses its own set of narrow engine operating by knocking. In order to solve this, inhomogeneity method of mixture and temperature is suggested. The purpose of this research is to get fundamental knowledge about the effect of thermal stratification on HCCI combustion of PRF -Air mixture. The temperature stratification is made by buoyancy effect in combustion chamber of RCM. The analysis items are pressure, temperature of in-cylinder gas and combustion duration. In addition, the structure of flames using the two dimensional chemiluminescence's images by a framing camera are analyzed. Under stratification, the LTR starting time and the HTR starting time are advanced than that of homogeneous. Further, the LTR period of homogeneous conditions became shorter than that of the stratified conditions. With the case of homogeneous condition, the luminosity duration becomes shorter than the case of stratified condition. Additionally, under stratified condition, the brightest luminosity intensity is delayed longer than at homogeneous condition.

• ETRI Journal
• /
• 제37권3호
• /
• pp.595-605
• /
• 2015

This paper proposes a robust, imperceptible block-based digital video watermarking algorithm that makes use of the Speeded Up Robust Feature (SURF) technique. The SURF technique is used to extract the most important features of a video. A discrete multiwavelet transform (DMWT) domain in conjunction with a discrete cosine transform is used for embedding a watermark into feature blocks. The watermark used is a binary image. The proposed algorithm is further improved for robustness by an error-correction code to protect the watermark against bit errors. The same watermark is embedded temporally for every set of frames of an input video to improve the decoded watermark correlation. Extensive experimental results demonstrate that the proposed DMWT domain video watermarking using SURF features is robust against common image processing attacks, motion JPEG2000 compression, frame averaging, and frame swapping attacks. The quality of a watermarked video under the proposed algorithm is high, demonstrating the imperceptibility of an embedded watermark.

• Structural Engineering and Mechanics
• /
• 제24권2호
• /
• pp.137-154
• /
• 2006

The reliable pushover analysis of RC structures requires a realistic prediction of moment-curvature relations, which can be obtained by utilizing proper constitutive models for the stress-strain relationships of laterally confined concrete members. Theoretical approach of Mander is still a single stress-strain model, which employs a multiaxial failure surface for the determination of the ultimate strength of confined concrete. Alternatively, this paper introduces a simple and practical failure criterion for confined concrete with emphasis on introduction of significant modifications into the two-parameter Drucker-Prager model. The new criterion is only applicable to triaxial compression stress state which is exactly the case in the RC columns. Unlike many existing multi-parameter criteria proposed for the concrete fracture, the model needs only the compressive strength of concrete as an independent parameter and also implies for the influence of the Lode angle on the material strength. Adopting Saenz equation for stress-strain plots, satisfactory agreement between the measured and predicted results for the available experimental test data of confined normal and high strength concrete specimens is obtained. Moreover, it is found that further work involving the confinement pressure is still encouraging since the confinement model of Mander overestimates the ultimate strength of some RC columns.

• Design & Manufacturing
• /
• 제10권2호
• /
• pp.6-11
• /
• 2016

Designed patterns of slit are introduced to the uni-directional (UD) prepreg in order to enhance the formability of the carbon/epoxy composites without wrinkling and laddering. Three different types of the slit alignment along the thickness direction are applied to analyse the deformation behavior during the compression moulding process of laminates. Degrees of the slit open and the mechanical strength are evaluated based on the level of the compaction pressure in the course of forming process. Results have shown that the mechanical strength of laminates having slits could attain at least 80% of the conventional ones without slits. However, further studies are required to identify the direct relevance of the slit alignment in laminate to the mechanical properties.